journal article·2004-12

Influence of high pressure normalizing heat treatment on microstructure and creep strength of high Cr steels

K. Kimura, S. Yamaoka

Publisher page

Abstract

Abstract Chromium is an effective element for improvement in the oxidation resistance of steels. However, chromium addition to ferritic creep resistant steel is restricted to around 9–10 wt.%, since excess addition of chromium results in formation of delta-ferrite which decreases creep strength and toughness. In this study, influence of normalizing heat treatment under high pressure on microstructure and creep strength has been investigated in a steel containing 15 wt.% of chromium, since austenite single phase region is extended up to about 20 wt.% of chromium under high pressure of about 4 GPa. In contrast to a ferritic microstructure of the steel normalized under atmospheric pressure of 100 kPa, the martensitic one was found in steel normalized under high pressure of 4 GPa. Hardness in the as tempered condition of the steels subjected to normalizing heat treatment at 1273 and 1173 K under 4 GPa was 290 and 289 HV, respectively. This is significantly higher than the value of 182 HV for the steel normalized at 1273 K under atmospheric pressure of 100 kPa. Creep rate of the steel normalized under high pressure of 4 GPa was significantly smaller than that of the steel normalized under pressure of 100 kPa. It has been concluded that high pressure normalizing heat treatment is effective to suppress a formation of delta-ferrite and to improve both creep strength and oxidation resistance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Metal Alloys Wear and Properties · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. Masuyama · ISIJ Int · 2001 · 41 · 61210.2355/isijinternational.41.612 ↗
2. P.J. Ennis, W.J. Quadakkers, in: Proceedings of the Fifth International Charles Parsons Turbine Conference, PARSONS 2000, Advanced Materials for 21st Century Turbines and Power Plant, The Institute of Materials, London, 2000, pp. 265–275.
3. Binary Alloy Phase Diagrams, vol. 2, 2nd ed., ASM International, 1990, pp. 1273.
4. Iseda · Therm. Nucl. Power · 1994 · 45 · 900
5. T. Itagaki, H. Kutsumi, M. Igarashi, F. Abe, in: Proceedings of the Seventh Liege Conference on Materials for Advanced Power Engineering, 2002, pp. 1639–1648.
6. C. Cheng, G.H. Meier, R.A. Perkins, W.T. Bekker, in: R.W. Bekker et al. (Eds.), Materials for Coal Gasification, ASM International, Metals Park, OH, 1988, p. 159.
7. Sundararajan · ISIJ Int · 2003 · 43 · 9510.2355/isijinternational.43.95 ↗
8. Sundararajan · ISIJ Int · 2003 · 43 · 10410.2355/isijinternational.43.104 ↗
9. Pascover · Acta Metall · 1969 · 17 · 32110.1016/0001-6160(69)90072-8 ↗
10. NRIM Creep Data Sheet, No. 43, National Research Institute for Metals, Tsukuba, Japan, 1996.
11. NIMS Creep Data Sheet, No. 48, National Institute for Materials Science, Tsukuba, Japan, 2002.
12. Kimura · Key Eng. Mater · 2000 · 171–174 · 48310.4028/www.scientific.net/KEM.171-174.483 ↗
13. Suzuki · Tetsu-to-Hagane · 2000 · 86 · 55010.2355/tetsutohagane1955.86.8_550 ↗
14. Ennis · Acta Mater · 1997 · 45 · 490110.1016/S1359-6454(97)00176-6 ↗
15. Hald · ISIJ Int · 2003 · 43 · 42010.2355/isijinternational.43.420 ↗
16. Toda · ISIJ Int · 2003 · 43 · 11210.2355/isijinternational.43.112 ↗