journal article·2002-03

Mechanical properties of a spray deposited bearing steel

Rainer Tinscher, Hubert Bomas, Peter Mayr

Publisher page

Abstract

Typical features of spray deposited steels are a homogeneous isotropic microstructure without any segregation, a porous region at the billet border and coarse grains in the core of the billet. To overcome coarse grain and porosity, a subsequent hot rolling and a following heat treatment is necessary. For the present work, the bearing steel SAE 52100 was used as a master material. By hot rolling, the initial microstructure was transformed to a homogeneous equiaxed fine-grained pearlitic microstructure without any remaining porosity. To get use of the characteristic properties of this high-strength steel, an isothermal bainitic hardening was carried out which again leads to a very homogeneous and isotropic microstructure. Information about the mechanical properties of this material was gained by tension and fatigue tests. Due to the isotropy of the microstructure, high fatigue resistance is not only observed for axial, but also for loads perpendicular to the rolling direction.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Powder Metallurgy Techniques and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Spray forming of low alloy steels
2. V. Uhlenwinkel, M. Buchholz, R. Tinscher, A. Schulz, J. Fischer, R. Schröder, Investigation of spray formed billets from bearing steel AISI 52100, in: Proceedings of the International Conference on Spray Forming IV, Baltimore, MD, USA, 13–15 September, 1999.
3. Annavarapu · Process Anal. Metall. Trans. · 1990 · A21 · 3077
4. B. Hribernik, H.P. Fauland, G. Hackl, B. Kriszt, Properties of spray formed high speed steel grade S11-2-5-8, in: Proceedings of the International Conference on Spray Forming I, Swansea, UK, September 17–19, 1990, pp. 27.01–27.15.
5. R. Kopp, G. Hirt, H. Beyer-Steinhauer, Umformtechnische Untersuchungen an sprühkompaktiertem Material, Stahl und Eisen 111 (1991) 10, 45–50.
6. R.L. Kozarek, M.G. Chu, S.J. Pien, An approach to minimize porosity in spray formed deposits through a model based designed experiment, in: Proceedings of the TMS Fall Meeting, 15–17 September 1997, Indianapolis, IN, USA; Solidification 1 (1998) 461–471.
7. Payne · Scrip. Metall. Mater. · 1993 · 29 · 90710.1016/0956-716X(93)90380-B ↗
8. K. Hummert, PM-Hochleistungsaluminium im industriellen Maßstab, Kolloquiums-band 4 (1998) SFB 372, Universität Bremen.
9. Igharo · Powder Metall. · 1989 · 32 · 12410.1179/pom.1989.32.2.124 ↗
10. Lee · Metall. Mater. Trans. A · 1998 · 29 · 139510.1007/s11661-998-0354-0 ↗
11. H.R. Müller, Eigenschaften und Einsatzpotential sprühkompaktierter Kupferlegierungen, Kolloquium des SFB 372, Band 1 (1996), Universität Bremen, 33–56.
12. Shaw · Int. J. Powder Metall. · 1997 · 33 · 31
13. Yabuuchi · Int. J. Japan Soc. Prec. Eng. · 1993 · 27 · 327
14. Th. Linkewitz, Berechnung der Wechselfestigkeit von gekerbten und mehrachsig beanspruchten Proben des Stahls 100Cr6 im bainitischen Zustand, Fortschritt-Berichte VDI, Reihe 18, Nr. 233, 1998.
15. F. Stahl, Ermüdungsverhalten von Wälzlagerkugeln aus Blockguss und Strangguss, Dissertation, Universität Bremen, 1996.
16. Murakami · JSME Ser. I · 1989 · 32 · 167
17. C. Krä, Beschreibung des Lebensdauerverhaltens gekerbter Proben unter Betriebsbelastung auf der Basis des statistischen Größeneinflusses, Dissertation, Universität der Bundeswehr München, 1988.