Influence of the green density on the dewaxing behaviour of uniaxially pressed powder compacts
Source abstract
Abstract
The effect of the green density on the dewaxing behaviour of two different uniaxially pressed iron based powder metallurgy alloys has been characterised by means of non-destructive mechanical and microstructural techniques, i.e. impulse excitation technique and synchrotron tomography. The elastic and damping properties of the green and dewaxed specimens pressed to two different densities have been evaluated. It was found that the as-pressed green specimens with lower density possessed higher stiffness and lower damping than the high density ones. This behaviour has been explained on a microstructural basis, considering the damage generated in the green specimens during the ejection step. The elastic and damping properties of the specimens after dewaxing strongly depended on their initial green density. Increased elastic properties (and lower damping) were observed for the low density specimens with respect to their green counterparts, while the opposite behaviour was observed for the specimens with higher green density (i.e. decreased stiffness and slightly higher damping after dewaxing). “In situ” monitoring of the evolution of the elastic and damping properties of the materials has been carried out by means of the high temperature impulse excitation technique to better understand the behaviour observed. Additionally, thermogravimetric analysis has been carried out to correlate the mass loss events with the relevant features of the HT-IET curves. It was demonstrated that the damage generated in the green specimens during ejection is amplified during dewaxing for the high density compacts, while some degree of pre-sintering is responsible for the increased properties of the lower density specimens.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Powder Metallurgy Techniques and Materials · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. P. Lindskog, Met. Powder Rep. 59(2) (2004) 10–11.10.1016/S0026-0657(04)00070-0 ↗
2. Warm compaction, in: Höganäs Handbook, vol. 4, Höganäs AB, Höganäs, Sweden, 1998.
3. Skoglund · Powder Metall. · 2001 · 44 · 199
4. S. Andersson, A. Ahlqvist. Proceedings of the 1998 PM World Congress on Powder Metallurgy, vol. 2, October 18–22, Granada, Spain, EPMA, pp. 261–265. ISBN 1-899072-09-8.
5. H. Danninger, C. Xu, L. Blanco, M. Campos, J.M. Torralba. Proceedings of the 2004 World Congress on Powder Metallurgy, October 17–21, vol. 2, Vienna, Austria, EPMA, pp. 19–24. ISBN 1899072 15 2.
6. ASTM E 1876-99, Standard test method for dynamic Young's modulus, shear modulus and Poisson's ratio by impulse excitation of vibration, 2000. ASTM committee E-28 on mechanical testing, subcommittee E2803 on elastic properties.
7. ENV 843-2, Advanced technical ceramics—monolithic ceramics, mechanical properties at room temperature. Part 2. Determination of elastic moduli, CEN, 1996.
8. Roebben · J. Alloys Compd. · 2000 · 310 · 28410.1016/S0925-8388(00)00966-X ↗
9. Firstov · Mater. Sci. Eng. A · 2004 · 378 · 210.1016/j.msea.2003.10.324 ↗
10. Cloetens · Appl. Phys. · 1997 · 81 · 587810.1063/1.364374 ↗
11. Bernard · J. Etourneau. Acta Mater. · 2005 · 53 · 12110.1016/j.actamat.2004.09.027 ↗
12. M. Nöthe, K. Pischang, P. Ponizil, B. Kieback, J. Ohser. Proceedings of the 2004 World Congress on Powder Metallurgy, vol. 2, October 17–21, Vienna, Austria, EPMA, pp. 229–234. ISBN 1899072 15 2.
13. Lame · Acta Mater. · 2004 · 52 · 97710.1016/j.actamat.2003.10.032 ↗
14. Vagnon · Acta Mater. · 2006 · 54 · 51310.1016/j.actamat.2005.09.030 ↗
15. Roebben · Rev. Sci. Instrum. · 1997 · 68 · 451110.1063/1.1148422 ↗
16. S. Giménez, T. Lauwagie, G. Roebben, W. Heylen, O. Van der Biest, J. Alloys Compd. (in press).
17. Nowick · 1972
18. Degnan · Powder Metall. · 2003 · 46 · 36510.1179/003258903225010785 ↗
19. Simchi · Powder Metall. · 2000 · 43 · 20910.1179/003258900665961 ↗
20. Simchi · Powder Metall. · 2000 · 43 · 21910.1179/003258900665970 ↗
21. Kuroki · Key Eng. Mater. · 1989 · 29 · 36510.4028/www.scientific.net/KEM.29-31.365 ↗
22. Kuroki · 1989
23. C. Binet, R. Zauner, D. Heaney. Proceedings of the 2004 World Congress on Powder Metallurgy, vol. 5, October 17–21, Vienna, Austria, EPMA, pp. 191–196. ISBN 1899072 15 2.
24. S. Giménez, G. Roebben, J. Vleugels, O. Van der Biest, Proceedings of the 2004 World Congress on Powder Metallurgy, vol. 5, October 17–21, Vienna, Austria, EPMA, pp. 423–428. ISBN 1899072 15 2.