journal article·2025-06Open access

Characterization of the milling-induced hardness gradient in the near-surface material volume of high manganese TWIP steel 1.7401 by nanoindentation

S. Wolke, M. Smaga, T. Beck

Abstract

The hardness gradient induced by up and down milling in the near-surface material volume of high-manganese TWIP steel 1.7401 was characterised up to a surface distance of 50 μm using nanoindentation. Hereby, even the influence of various small indentation depths was such pronounced that the indentation size effect influenced the measured hardness significantly and was, hence, studied. In a first step, the effect of uniaxial, quasi-static deformation on hardness was investigated, which serves as a comparison to hardening by milling which is associated with a complex, multiaxial deformation. Subsequently, suitable parameters for characterization of the milling induced hardness gradient were identified through variation of indentation depths and indentation depth-to-indent spacing ratios. Additionally, the near-surface hardness gradient was examined transversely and longitudinally to the feed direction to analyse whether possible process-induced differences occur due to intermittent cutting. Furthermore, the hardness in the nanocrystalline layer was examined in detail and correlated with the respective microstructures, observed through FIB cutting and ion beam imaging. Finally, the hardness gradients after up and down milling were compared, the effect of electrolytic polishing on the near surface hardness gradient was analysed and the hardness in the rolling skin, representing the initial state, was studied. Milling results in a maximum increase in hardness of approximately 50 % in comparison with the base material, and the hardness decreases degressively with increasing distance to the surface up to a depth of approximately 20 μm. Hardness increases in the milling-induced near-surface material which can be attributed to higher dislocation density. The near-surface layer, measuring 1–2 μm in depth, consists of fine-grained material, and the transition to coarser grains corresponds with a change in hardness slope. No significant hardness gradient was detected along the feed direction, and up and down milling results in similar hardness gradients. • Hardness in the near surface material volume after milling decreases degressively with increasing surface distance and transitions asymptotically the base material’s hardness at a surface distance of approximately 20 μm • Indentation size effect is affected by the uniaxial quasi-static deformation which provides indications about dislocation density after quasi-static deformation and milling • The locally discontinuous transition from the nanocrystalline near surface material volume to the coarser grained material volume exhibits a continuous hardness change • Both up and down milling result in comparable hardness gradients in the near surface material volume
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. DIN Deutsches Institut für Normung e.V., ISO 25178-2:2021: Geometrical Product Specifications (GPS) – Surface Texture: Areal – Part 2: Terms, Definitions and Surface Texture Parameters.
2. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
3. High cycle fatigue behavior of high-Mn TWIP steel with different surface morphologies10.1016/j.ijfatigue.2020.105499 ↗
4. Influences of up-milling and down-milling on surface integrity and fatigue strength of X160CrMoV12 steel10.1007/s00170-019-04280-2 ↗
5. Surface integrity evolution and fatigue evaluation after milling mode, shot-peening and polishing mode for TB6 titanium alloy10.1016/j.apsusc.2016.06.162 ↗
6. M. Smaga, T. Beck, M. Kopnarski, R. Merz, K.M. de Payrebrune, S. Wolke, Influence of Surface Morphology on Fatigue and Tribological Behavior of TRIP/TWIP Steels 289–312. https://doi.org/10.1007/978-3-031-35575-2_12.10.1007/978-3-031-35575-2_12 ↗
7. A. Boemke, Einfluss kryogen gedrehter Randschichten auf das Ermüdungsverhalten des metastabilen austenitischen Stahls X6CrNiNb1810 und des stabilen austenitischen Stahls X1NiCrMoCu25205 bis in den VHCF-Bereich. PhD thesis.
8. Influence of surface morphology on the fatigue behavior of metastable austenitic steel
9. On the evolution of residual stresses, microstructure and cyclic performance of high-manganese austenitic TWIP-steel after deep rolling10.3390/met9080825 ↗
10. Influence of surface morphology on fatigue behavior of metastable austenitic stainless steel AISI 347 at ambient temperature and 300°C10.1016/j.prostr.2017.07.150 ↗
11. 2024
12. Machining of austenitic stainless steels - a review10.1504/IJMMM.2012.048564 ↗
13. Hot machining of austenitic manganese steel by shaping10.1016/0020-7357(71)90046-1 ↗
14. Twinning-induced plasticity (TWIP) steels10.1016/j.actamat.2017.06.046 ↗
15. High manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships10.1016/j.cossms.2011.04.002 ↗
16. State of the art in finite element approaches for milling process: a review10.1007/s40436-022-00417-x ↗
17. Cyclic hardness test PHYBALCHT – short-time procedure to evaluate fatigue properties of metallic materials10.1016/j.ijfatigue.2014.01.009 ↗
18. The correlation of indentation experiments10.1016/0022-5096(70)90029-3 ↗
19. Deformation induced surface hardening when turning metastable austenitic steel AISI 347 with different cryogenic cooling strategies10.1016/j.procir.2014.03.097 ↗
20. A comparative study of hard turned and cylindrically ground white layers10.1016/j.ijmachtools.2003.10.009 ↗
21. The effect of machining on the surface integrity and fatigue life10.1016/j.ijfatigue.2008.01.005 ↗
22. The indentation size effect: a critical examination of experimental observations and mechanistic interpretations10.1146/annurev-matsci-070909-104456 ↗
23. Review of nanoindentation size effect: experiments and atomistic simulation10.3390/cryst7100321 ↗
24. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
25. A review of nanoindentation continuous stiffness measurement technique and its applications10.1016/S1044-5803(02)00192-4 ↗
26. Thermodynamic modeling of the stacking fault energy of austenitic steels10.1016/j.actamat.2010.10.037 ↗
27. DIN Deutsches Institut für Normung e.V., DIN EN ISO 6892-1:2014: Metallic Materials - Tensile Testing - Part 1: Method of Test at Room Temperature (ISO/DIS 6892-1:2014), accessed 2014.
28. A critical assessment of the effect of indentation spacing on the measurement of hardness and modulus using instrumented indentation testing10.1016/j.matdes.2018.107563 ↗
29. Indentation size effect in metallic materials: modeling strength from pop-in to macroscopic hardness using geometrically necessary dislocations10.1016/j.actamat.2006.01.036 ↗
30. Indentation size effect in metallic materials: correcting for the size of the plastic zone10.1016/j.scriptamat.2005.02.009 ↗
31. Orientation dependent twinning behavior in a twinning-induced plasticity steel investigated by nanoindentation10.1007/s12540-022-01180-1 ↗
32. On the stacking fault energy of Fe-18 Pct Mn-0.6 Pct C-1.5 Pct Al twinning-induced plasticity steel10.1007/s11661-011-0610-6 ↗
33. Influence of the surface morphology on the cyclic deformation behavior of HSD® 600 steel10.1051/matecconf/201816506010 ↗
34. Single crystal elastic constants of high-manganese transformation- and twinning-induced plasticity steels determined by a new method utilizing nanoindentation10.1016/j.msea.2013.04.049 ↗
35. The respective hardening contributions of dislocations and twins to the flow stress of a twinning-induced plasticity steel10.1016/j.scriptamat.2015.09.003 ↗
36. TEM study on the surface white layer in two turned hardened steels10.1016/S0921-5093(01)01447-2 ↗
37. Analysis of white layers formed in hard turning of AISI 52100 steel10.1016/j.msea.2004.08.052 ↗
38. Quantitative microstructural analysis of nanocrystalline surface layer induced by a modified cutting process
39. Modeling nanostructural surface modifications in metal cutting by an approach of thermodynamic irreversibility: derivation and experimental validation10.1007/s00161-016-0533-y ↗
40. Thermodynamics-based interpretation of white layer formation in metal cutting10.1016/j.procir.2017.03.328 ↗
41. The state of the art for numerical simulations of the effect of the microstructure and its evolution in the metal-cutting processes10.1016/j.ijmachtools.2022.103890 ↗