From as-cast to heat treated X-40 superalloy: Effect of cooling rate after partial solution treatment on microstructural evolutions and mechanical properties
Source abstract
Abstract
Abstract This research study aims at investigating the influence of partial solution treatment and the subsequent cooling strategy on the microstructure and mechanical properties of an as-cast Co–Cr–W superalloy. Three different cooling scenarios were employed to explore the effect of cooling rate on the carbide reprecipitation potential from the \solid solution formed during the heat treatment. The partial dissolution/breakdown of the continuous network of the Cr-rich M7C3 carbides during the partial solution treatment cycle along with their transformation to M23C6 carbides and formation of secondary carbides during the cooling stage were taken into account to discuss the obtained hardness values, and high-temperature creep results. Regardless of the applied cooling rate, the secondary carbides were formed during the cooling stage, and the heat-treated samples showed almost the same microstructure and mechanical properties, which eliminates the need for the aging cycle. This can alleviate the concerns associated with the heat treatment of the large-size X-40 industrial components since the gradient in the cooling rate after the heat treatment cycle would not lead to non-uniform parts. From the hardness and creep viewpoints, all of the samples could meet the minimum requirements of the X-40 superalloy. Mechanical properties suggest that the applied partial solution treatment cycle can be considered as a suitable candidate for high-temperature applications of X-40 superalloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Advanced Materials Characterization Techniques · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Klarstrom · 2004 · 762
2. High temperature oxidation behavior of a novel cobalt-nickel-base superalloy10.1016/j.jallcom.2018.06.275 ↗
3. Wrought cobalt-base superalloys10.1007/BF02661736 ↗
4. Influence of thermomechanical processing parameters on microstructural evolution of a gamma-prime strengthened cobalt based superalloy during high temperature deformation10.1016/j.msea.2020.139498 ↗
5. Effects of aluminum and molybdenum content on the microstructure and properties of multi-component γ′-strengthened cobalt-base superalloys10.1016/j.msea.2018.09.058 ↗
6. Recrystallization in a directionally solidified cobalt-base superalloy10.1016/j.msea.2007.07.028 ↗
7. Achieving lower mass density with high strength in Nb stabilised γ/γ′ Co–Al–Mo–Nb base superalloy by the replacement of Mo with V10.1016/j.msea.2020.139826 ↗
8. Rejuvenation of degraded first stage gas turbine nozzle by heat treatment10.1016/j.jallcom.2010.03.070 ↗
9. R. Viswanathan, Damage Mechanisms and Life Assessment of High Temperature Components, ASM international1989.10.31399/asm.tb.dmlahtc.9781627083409 ↗
10. Influence of service-induced microstructural changes on the failure of a cobalt-based superalloy first stage nozzle10.1016/j.matdes.2010.02.021 ↗
11. The effect of long-term service exposure on the stability of carbides in Co–Cr–Ni–W (X-45) superalloy10.1016/j.engfailanal.2017.11.018 ↗
12. Brazing and wide gap repair of X-40 using Ni-base alloys10.1115/1.2836743 ↗
13. Microstructure and high temperature tensile properties of narrow gap braze joint between X-40 and IN73810.1179/174328408X369401 ↗
14. Secondary carbide precipitation in a directionally solified cobalt-base superalloy10.1007/s11661-999-0043-7 ↗
15. ASM specialty handbook: nickel, cobalt, and their alloys
16. Influence of type and morphology of carbides on stress-rupture behavior of a cast cobalt-base superalloy10.1016/j.jallcom.2017.08.287 ↗
17. High-temperature microstructures of ternary Co-30 wt.% Cr-based alloys over the [0–2.0 wt.%] carbon range10.1016/j.jallcom.2007.12.023 ↗
18. Carbide behaviour during high temperature low cycle fatigue in a cobalt-base superalloy10.1023/A:1004683301816 ↗
19. Effects of heat treatment on microstructures and mechanical properties of a directionally solidified cobalt-base superalloy10.1016/S0921-5093(99)00183-5 ↗
20. Effects of high-temperature ageing on the creep-rupture properties of high-tungsten cobalt-base superalloys10.1007/BF00356809 ↗
21. Sims · 1969
22. Precipitation path of secondary phases during solidification of the Co–25.5% Cr–5.5% Mo–0.26% C alloy10.1016/S1359-6462(02)00305-6 ↗
23. A. International, Standard Test Method for Brinell Hardness of Metallic Materials, ASTM International2012.
24. E8
25. Microstructural evolution mechanism during brazing of Hastelloy X superalloy using Ni–Si–B filler metal10.1080/13621718.2017.1410341 ↗
26. Intermetallic phase formation during brazing of a nickel alloy using a Ni–Cr–Si–Fe–B quinary filler alloy10.1080/13621718.2018.1553280 ↗
27. Secondary M6C precipitation in a cobalt–base superalloy10.1023/A:1006627122234 ↗
28. The superalloys, ed. By CT sims and W, C
29. Cooling rate and carbon content effect on the fraction of secondary phases precipitate in as-cast microstructure of ASTM F75 alloy10.1016/j.jmatprotec.2008.04.039 ↗
30. Effect of carbides on the creep properties of a Ni-base superalloy M96310.1016/j.msea.2005.02.038 ↗
31. Askeland · 2003
32. Degradation processes in high-temperature creep of cast cobalt-based superalloys10.1016/j.matchar.2018.08.006 ↗