journal article·2021-01

Designing ultrahard aluminum nanocomposites by severe mechanochemical processing

Clênio Silva, Roberto B. Figueiredo, Berenice M. Gonzalez, Luciano A. Montoro, Augusta Isaac

Publisher page

Abstract

Abstract In this study, we deployed a severe mechanochemical approach to produce ultrahard Al–Nb nanocomposites. Two nanocomposites were fabricated by high-pressure torsion (HPT) at room temperature of commercially pure Al and 10 wt% Nb2O5 with distinct morphologies (extremely thin nanowires or nanorods). In addition to consolidation of powders, structural refinement and chemical mixing, HPT was applied here for inducing mechanochemical redox reactions between Al and nanostructured Nb2O5 (Nb2O5 + 10/3 Al → 2Nb + 5/3 Al2O3). These chemical reactions released metallic niobium in its atomic form, which contributed to the dynamics of mixing between Al and Nb at the atomic scale. This strategy demonstrated to be effective for promoting the formation of supersaturated (Al–Nb) solid solution, niobium clustering, and extensive segregation of Nb at lattice defects. The effect of different nanostructured Nb2O5 morphologies on the interface structures and hardening of the produced composites was discussed. Annealing at moderate temperature (373 K for 1 h) caused an exceptional increase in hardness of ~54% (~289 Hv) for the composite produced using Nb2O5 nanorods. This was attributed to the rearrangement of dislocations into a lower energy configuration (dislocation tangles) and an astounding segregation of Nb to this dislocation structure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Boron and Carbon Nanomaterials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. The deformation and ageing of mild steel: III Discussion of results10.1088/0370-1301/64/9/303 ↗
2. The Cleavage Strength of Polycrystals
3. Grain boundary stability governs hardening and softening in extremely fine nanograined metals10.1126/science.aal5166 ↗
4. Strength enhancement of an aluminum alloy through high pressure torsion10.1016/j.msea.2019.05.102 ↗
5. Mechanical properties of nanocrystalline materials10.1016/j.pmatsci.2005.08.003 ↗
6. Thermal stability: the next frontier for nanocrystalline materials
7. Strength, grain refinement and solute nanostructures of an Al-Mg-Si alloy (AA6060) processed by high-pressure torsion10.1016/j.actamat.2013.10.022 ↗
8. Towards strength–ductility synergy through the design of heterogeneous nanostructures in metals10.1016/j.mattod.2017.02.003 ↗
9. New nanoscale toughening mechanisms mitigate embrittlement in binary nanocrystalline alloys10.1039/C8NR06419A ↗
10. Microstructure, mechanical properties and aging behaviour of nanocrystalline copper–beryllium alloy10.1016/j.msea.2018.12.011 ↗
11. Deformation induced grain boundary segregation in nanolaminated Al–Cu alloy10.1016/j.actamat.2019.10.036 ↗
12. Achieving ultrahigh tensile strength of 1 GPa in a hierarchical nanostructured 2024 Al alloy
13. Stabilization and strengthening of nanocrystalline copper by alloying with tantalum10.1016/j.actamat.2012.01.011 ↗
14. Tantalum and zirconium induced structural transitions at complex [111] tilt grain boundaries in copper10.1016/j.actamat.2020.02.064 ↗
16. Thermodynamic stabilization of nanocrystallinity
17. Stability of binary nanocrystalline alloys against grain growth and phase separation10.1016/j.actamat.2012.12.033 ↗
18. Competition for impurity atoms between defects and solid solution during high pressure torsion10.1016/j.scriptamat.2019.08.001 ↗
19. Effect of Mg on microstructure and mechanical properties of Al-Mg alloys produced by high pressure torsion
20. Nanostructure and properties of a Cu-Cr composite processed by severe plastic deformation10.1016/j.scriptamat.2008.02.010 ↗
21. Dynamic precipitation, segregation and strengthening of an Al-Zn-Mg-Cu alloy (AA7075) processed by high-pressure torsion
22. Microstructural evolution, strengthening and thermal stability of an ultrafine-grained Al-Cu-Mg alloy10.1016/j.actamat.2016.02.050 ↗
23. Mechanical alloying of Cu and Fe induced by severe plastic deformation of a Cu-Fe composite10.1016/j.actamat.2005.01.024 ↗
24. Atomic-scale analysis of the segregation and precipitation mechanisms in a severely deformed Al-Mg alloy10.1016/j.actamat.2014.03.033 ↗
25. Mixing instabilities during shearing of metals10.1038/s41467-017-01879-5 ↗
26. The formation of supersaturated solid solutions in Fe-Cu alloys deformed by high-pressure torsion10.1016/j.actamat.2011.10.044 ↗
27. Interface structures in Al-Nb2O5 nanocomposites processed by high-pressure torsion at room temperature10.1016/j.matchar.2020.110222 ↗
28. Fabrication of nanocomposites through diffusion bonding under high-pressure torsion
29. Micro-mechanical and tribological properties of aluminum-magnesium nanocomposites processed by high-pressure torsion10.1016/j.msea.2016.12.067 ↗
30. A magnesium-aluminium composite produced by high-pressure torsion
31. Hallmarks of mechanochemistry: from nanoparticles to technology10.1039/c3cs35468g ↗
32. Chemically sensitive structure-imaging with a scanning transmission electron microscope10.1038/336565a0 ↗
33. Extractive metallurgy of niobium, tantalum, and vanadium10.1179/imr.1984.29.1.405 ↗
34. Preparation of niobium-aluminium alloys by aluminothermic reduction of Nb2O510.1515/HTMP.2005.24.1.1 ↗
35. Annealing‐induced hardening in ultrafine‐grained and nanocrystalline materials10.1002/adem.201900507 ↗