journal article·2020-06

Mechanical properties and tempering resistance of an ultrafine grained Tool Steel-PSZ composite fabricated by high energy mechanical milling and spark plasma sintering

F. Deirmina, M. Pellizzari

Publisher page

Abstract

Abstract The mechanical properties and tempering resistance of a powder metallurgical (PM) tool steel (AISI H13) reinforced with partially stabilized zirconia (PSZ) were investigated. The choice of particles reinforcement was made in view to the well-known phase transformation toughening effect in PSZ. Composite powders were produced by high energy mechanical milling and subsequently consolidated by spark plasma sintering (SPS). An ultrafine grain microstructure was achieved showing a homogenous distribution of refined PSZ particles within the severely deformed matrix. Thanks to the fast SPS consolidation, a small amount (less than 2 vol%) of reaction products were formed. The hardness of the composites was significantly higher than the unreinforced counterpart, due to the microstructural refinement, increased dislocation density, and dispersion hardening. Tempering resistance at 550 °C and 650 °C was also significantly improved. The hot compressive yield strength of the composites measured 650 °C and 450 °C was increased up to 1.8 times compared to unreinforced steel. PSZ phase transformation during hot compression contributed to increased work hardening. Fracture toughness was significantly decreased compared to the base material. However, compared to a TiC reinforced H13 with the same hardness, a marginal increase in apparent fracture toughness was observed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Advanced ceramic materials synthesis · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. Processing and properties of particulate reinforced steel matrix composites10.1016/S0921-5093(97)00710-7 ↗
2. Microstructure evolution and wear properties of in situ synthesized TiB2 and TiC reinforced steel matrix composites10.1016/j.jallcom.2007.05.018 ↗
3. Development and performance of new hard and wear-resistant engineering materials10.1007/s11665-997-0077-1 ↗
4. A comparison of the reciprocating sliding wear behaviour of steel based metal matrix composites processed from self-propagating high-temperature synthesised Fe–TiC and Fe–TiB2 masteralloys10.1016/S0043-1648(02)00051-0 ↗
5. Review on TiC reinforced steel composites10.1023/A:1017947206490 ↗
6. Microstructure and mechanical properties of hot work tool steel matrix composites produced by hot isostatic pressing10.1179/pom.1997.40.1.55 ↗
7. Mechanical alloying of TiC/M2 high speed steel composite powders and sintering investigation10.1016/S0921-5093(01)00929-7 ↗
8. Fracture toughness of a hot work tool steel-TiC composite produced by mechanical milling and spark plasma sintering10.1016/j.msea.2017.10.053 ↗
9. Comparison of wear resistant MMC and white cast iron10.1016/S0043-1648(02)00300-9 ↗
10. Powder-metallurgy tool steels10.1179/pom.1978.21.2.114 ↗
11. Bonding, structure, and properties of metal/ceramic interfaces: Part 1 Chemical bonding, chemical reaction, and interfacial structure10.1179/imr.1993.38.5.233 ↗
12. Mechanical behavior of particle reinforced metal matrix composites10.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO;2-I ↗
13. Perspective on the development of high-toughness ceramics10.1111/j.1151-2916.1990.tb06493.x ↗
14. Densification behaviour of mixtures of hard and soft powders under pressure10.1016/S0032-5910(99)00293-4 ↗
15. Characterization of SiCp/2024 aluminum alloy composites prepared by mechanical processing in a low energy ball mill10.1016/S0921-5093(98)01030-2 ↗
16. Mechanical alloying for the effective dispersion of sub-micron SiCp reinforcements in Al–Li alloy composite10.1016/S0921-5093(98)00566-8 ↗
17. Effect of mechanical alloying on the morphology, microstructure and properties of aluminium matrix composite powders10.1016/S0921-5093(02)00246-0 ↗
18. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
19. Nanostructured/ultrafine multiphase steel with enhanced ductility obtained by mechanical alloying and spark plasma sintering of powders10.1016/j.msea.2009.03.021 ↗
20. Improvement of mechanical properties in SUS304L steel through the control of bimodal microstructure characteristics10.1016/j.msea.2014.01.023 ↗
21. Alternative mechanical milling routes for grain-refinement of conventional high-speed steel powder for later consolidation by SPS....640
22. Microstructural study and densification analysis of hot work tool steel matrix composites reinforced with TiB2 particles10.1016/j.matchar.2013.09.012 ↗
23. The effect of electric field and pressure on the synthesis and consolidation of materials: a review of the spark plasma sintering method10.1007/s10853-006-6555-2 ↗
24. Mechanical and microstructure comparison between microwave and spark plasma sintering of Al–B4C composite10.1016/j.jallcom.2015.09.024 ↗
25. Fedrizzi · 2013
26. Fabrication and properties of the TiC reinforced high-strength steel matrix composite10.1016/j.ijrmhm.2016.03.013 ↗
27. Spark plasma Co-sintering of mechanically milled tool steel and high speed steel powders10.3390/ma9060482 ↗
28. Enhanced mechanical properties of an Al based metal matrix composite prepared using mechanical alloying10.1016/S0921-5093(98)00676-5 ↗
29. Microstructure and thermal stability of fine-grained (Y, Mg)-PSZ ceramics with alumina additions10.1016/0955-2219(93)90025-M ↗
30. TEM observation of dynamic distortion in 2Y-PSZ/steel composites10.1016/S0272-8842(03)00065-8 ↗
31. Reinforcing mechanism of Mg-PSZ particles in highly-alloyed TRIP steel10.1002/srin.201100099 ↗
32. Production and characterization of a tool steel-PSZ composite by mechanical alloying and spark plasma sintering10.1016/j.jallcom.2017.03.203 ↗
33. Influence of high-energy ball milling on Mg-PSZ-reinforced TRIP steel-matrix composites synthesized by FAST/SPS10.1016/j.msea.2019.05.104 ↗
34. Sviluppo di un acciaio per lavorazione a caldo rinforzato tramite alligazione meccanica
35. Combined texture and structure analysis of deformed limestone from time-of-flight neutron diffraction spectra10.1063/1.364220 ↗
36. ASTM E92-82 · 2003
37. Evaluation of fracture toughness using small notched specimens10.1016/S0921-5093(01)01804-4 ↗
38. Influence of powder surface oxidation on some properties of a HIPed martensitic chromium steel
39. Production of a powder metallurgical hot work tool steel with harmonic structure by mechanical milling and spark plasma sintering
40. Kinetics of the austenite→martensite transformation10.1007/BF03398922 ↗
41. Phase transformation from fine-grained austenite10.2355/isijinternational.48.1038 ↗
42. The influence of austenite strength upon the austenite-martensite transformation in alloy steels10.1007/BF02641994 ↗
43. Fracture toughness of nanocrystalline tetragonal zirconia with low yttria content10.1016/S1359-6454(02)00283-5 ↗
44. Bonding of TRIP-steel/Al2O3-(3Y)-TZP composites and (3Y)-TZP ceramic by a spark plasma sintering (SPS) apparatus10.3390/ma9070558 ↗
45. Effect of heat treatment on grain size, phase Assemblage, and mechanical properties of 3 mol% Y-tzp10.1111/j.1151-2916.1996.tb08980.x ↗
46. Interfacial reactions in TRIP-steel/ZrO2 composites10.1002/srin.201100132 ↗
47. ON the yield strength OF quenched low-carbon lath martensite
48. Effect of thermal expansion coefficients on the martensitic transformation in a steel matrix composite
49. The role of internal stresses on the phase transformation of iron alloys10.1016/S1359-6462(97)00054-7 ↗
50. Martensite in steel: strength and structure10.1016/S0921-5093(99)00288-9 ↗
51. Mechanical and microstructural behaviour of isothermally and thermally fatigued ferritic/martensitic steels10.1016/S0022-3115(02)01086-3 ↗
52. Microstructure evolution of hot-work tool steels during tempering and definition of a kinetic law based on hardness measurements10.1016/j.msea.2004.03.067 ↗
53. High-temperature properties and microstructural stability of hot-work tool steels10.1016/j.msea.2009.06.010 ↗
54. Solidification structure of gas-atomized high-speed steel powders10.1179/pom.1982.25.1.1 ↗
55. Dieter · 1986
56. Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites10.1016/j.msea.2006.10.184 ↗
57. Anisotropic thermal expansion coefficients of Y2O3‐stabilized tetragonal zirconia10.1111/j.1151-2916.1986.tb07424.x ↗
58. Deirmina · 2017
59. Ambient and high-temperature stable fracture tests in ceramics: applications to yttria-partially-stabilized zirconia10.1111/j.1151-2916.1993.tb04041.x ↗
60. Study of reinforcing mechanisms in TRIP-matrix composites under compressive loading by means of micromechanical simulations10.1002/adem.201200323 ↗
61. Effects of interfacial debonding on the rate-dependent response of metal matrix composites10.1016/j.actamat.2005.07.004 ↗
62. Characterization of internal damage in a MMCp using X-ray synchrotron phase contrast microtomography10.1016/S1359-6454(99)00024-5 ↗
63. Equal channel angular pressing of metal matrix composites: effect on particle distribution and fracture toughness10.1016/j.actamat.2005.07.010 ↗