journal article·2018-03

Creep deformation of Co-Re-Ta-C alloys with varying C content–investigated in-situ by simultaneous synchrotron radiation diffraction

Lukas Karge, Ralph Gilles, Debashis Mukherji, Andreas Stark, Premek Beran, Norbert Schell, Michael Hofmann, Pavel Strunz, Johannes Häusler, Joachim Rösler

Publisher page

Abstract

Abstract The creep deformation of precipitation hardened Co-Re-Ta-C alloys is investigated during in-situ synchrotron diffraction experiment at 1373 K. At room temperature, the alloys have a structure consisting of ϵ -Co (hcp) and metastably retained γ -Co (fcc) and are strengthened by precipitates of the mono-carbide of Ta, which are finely dispersed in the alloy matrix. The alloy exhibits an allotropic ϵ → γ -Co phase transformation when heating to > 1173 K . A lower C content in the alloy generally promotes this transformation. It is shown that this transformation is strongly influenced by application of compressive load. The transformation ϵ → γ -Co at high temperature under load leads to microstructure refinement and subsequently to dissolution of hardening precipitates. This results in a considerable acceleration of the creep rate. Further, the equilibrium ratio of γ / ϵ -Co phase is significantly altered under compressive load. This behavior is attributed to a volume relaxation as the ϵ - and γ -Co phase have different unit cell volumes.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Metallurgical and Alloy Processes · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Co-Re-based alloys10.1002/adem.200700132 ↗
2. Microstructures of Co-Re-Cr, Mo-Si and Mo-Si-B high-temperature alloys10.1016/j.msea.2008.06.054 ↗
3. Co-Re-based alloys for high temperature applications: Design considerations and strengthening mechanisms
4. Neutron and synchrotron probes in the development of Co-Re-based alloys for next generation gas turbines with an emphasis on the influence of boron additives10.1107/S1600576714013624 ↗
5. Creep properties beyond 1100° C and microstructure of Co-Re-Cr alloys10.1016/j.msea.2010.09.035 ↗
6. Stability of TaC precipitates in a Co-Re-based alloy being developed for ultra-high-temperature applications10.1107/S1600576716009006 ↗
7. L. Karge, R. Gilles, D. Mukherji, P. Strunz, P. Beran, M. Hofmann, J. Gavilano, U. Keiderling, O. Dolotko, A. Kriele, A. Neubert, J. Rösler, W. Petry, The influence of C/Ta ratio on TaC precipitates in Co-Re base alloys investigated by small-angle neutron scattering, Acta Materialia ISSN 13596454, http://dx.doi.org/10.1016/j.actamat.2017.04.029.10.1016/j.actamat.2017.04.029 ↗
8. Investigation of phase transformations by in-situ neutron diffraction in a Co-Re-based high temperature alloy10.1016/j.matlet.2010.08.066 ↗
9. The Hexagonal Close-Packed (HCP) ⇋ Face-Centered Cubic (FCC) transition in Co-Re-based experimental alloys investigated by neutron scattering10.1007/s11661-011-1058-4 ↗
10. Effect of composition on the matrix transformation of the Co-Re-Cr-Ta-C alloys10.1007/s12540-016-5697-2 ↗
11. High-temperature strength and damage evolution in short fiber reinforced aluminum alloys studied by miniature creep testing and synchrotron microtomography10.1016/j.actamat.2011.09.022 ↗
12. Effect of carbon addition on solidification behavior, phase evolution and creep properties of an intermetallic β-stabilized γ-TiAl based alloy10.1016/j.intermet.2013.11.011 ↗
13. Influence of iridium on the properties of γ′-strengthened Co-base superalloys10.1002/adem.201400266 ↗
14. Deformation characteristics of the intermetallic alloy 60NiTi10.1016/j.intermet.2016.11.003 ↗
15. N. Schell, A. King, F. Beckmann, T. Fischer, M. Müller, A. Schreyer, The high energy materials science beamline (HEMS) at PETRA III, in: Materials Science Forum, vol. 772, Trans Tech Publ, ISBN 3037859113, 57–61, 2014.10.4028/www.scientific.net/MSF.772.57 ↗
16. A. Hammersley, FIT2D: an introduction and overview, European Synchrotron Radiation Facility Internal Report ESRF97HA02T 68.
17. A profile refinement method for nuclear and magnetic structures10.1107/S0021889869006558 ↗
18. Recent advances in magnetic structure determination by neutron powder diffraction10.1016/0921-4526(93)90108-I ↗
19. M. Hofmann, G.A. Seidl, J. Rebelo-Kornmeier, U. Garbe, R. Schneider, R.C. Wimpory, U. Wasmuth, U. Noster, The new materials science diffractometer STRESS-SPEC at FRM-II, in: Materials science forum, vol. 524, Trans Tech Publ, ISBN 0878494146, 211–216, 2006.10.4028/0-87849-414-6.211 ↗
20. Grain size measurement in experimental Co-Re-based alloys to study grain coarsening10.3139/147.110307_02 ↗
21. Weak-beam study of glide dislocations in hcp cobalt10.1080/01418618308234904 ↗
22. Strain-induced grain refinement of cobalt during surface mechanical attrition treatment10.1016/j.actamat.2004.10.021 ↗
23. Kinetics of the Fcc to Hcp phase-transformation and the formation of martensite in pure cobalt10.1016/0956-716X(95)00253-R ↗
24. γ→ϵ martensite transformation and twinning deformation in fcc cobalt during surface mechanical attrition treatment10.1016/j.scriptamat.2004.12.004 ↗
25. Apparent and effective creep parameters in single crystals of a nickel base superalloy-I Incubation period10.1016/0001-6160(77)90092-X ↗
26. A high temperature deformation mechanism map for the high performance Ni-base superalloy GTD-11110.1016/S0921-5093(00)01822-0 ↗
27. Hot working characteristics of cobalt in the temperature range 600−950°C10.1016/j.scriptamat.2008.09.012 ↗
28. Aspects of dynamic recrystallization in cobalt at high temperatures10.1007/s11661-009-9782-8 ↗