Effects of prior microstructures and deformation parameters on the ultra-refining uniformity of Ti-Mo ferritic steel
Source abstract
Abstract
Abstract Samples with different prior microstructures, quasi-polygonal ferritic (QPF) matrix and polygonal ferritic (PF) matrix, were compressed at 500 ℃ with different strain rates. As for the QPF matrix, its microstructure more tend to be compressed and refined under small strain rate, while it is opposite for the PF matrix. Increase of deformation temperature to 600 ℃ and 700 ℃ illustrates that during cDRX process, extending of geometric necessary boundaries (GNBs) increases the flow stress whereas the rearrangement of geometric necessary dislocations (GNDs) mainly causes the softening phenomenon. Additionally, extending of GNBs in prior grains firstly facilitates the increase of texture intensity on certain orientations, then the texture intensity decreases with further conduct of continuous dynamic recrystallization (cDRX) process, during which the subgrains mainly rotate along //SD or //SD and make orientations distributed more randomly within fiber textures. Deformation at 600 ℃ shows better refining effect and the average grain size can be refined to submicron scale, however, deformation at 700 ℃ presents better ultra-refining uniformity that the area fraction of ultra-refined regions can reach 94.8% with an average grain size of 1.1 µm. TEM observation clarifies that with the increase of deformation temperature, low angle boundaries (LABs) will replace dislocation walls dividing the prior grains and show better extending ability. Activation energy of the cDRX process also been estimated and it is about 768 KJ/mol.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Grain refinement in surface layers through deformation-induced ferrite transformation in microalloyed steel plate10.1016/j.matdes.2016.09.097 ↗
2. Three-dimensional crystal plasticity finite element analysis of microstructure and texture evolution during channel die compression of IF steel10.1016/j.commatsci.2014.09.032 ↗
3. Twenty-five years of ultrafine-grained materials: achieving exceptional properties through grain refinement10.1016/j.actamat.2013.08.018 ↗
4. Thermomechanical processing route to achieve ultrafine grains in low carbon microalloyed steels10.1016/j.actamat.2016.08.010 ↗
5. Dissolution and precipitation behaviour in steels microalloyed with niobium during thermomechanical processing10.1016/j.actamat.2015.06.057 ↗
6. Microstructure and texture of Nb+Ti stabilized ferritic stainless steel10.1016/j.matchar.2008.03.018 ↗
7. Evolution of recrystallization texture in a 0.78wt% Cr extra-low-carbon steel after warm and cold rolling10.1016/j.actamat.2011.04.027 ↗
8. A novel high-strain-rate ferrite dynamic softening mechanism facilitated by the interphase in the austenite/ferrite microstructure10.1016/j.actamat.2016.12.045 ↗
9. Hall-Petch relationship for austenitic stainless steels processed by large strain warm rolling10.1016/j.actamat.2017.06.060 ↗
10. Effects of temperature and strain rate on flow behavior and microstructural evolution of super duplex stainless steel under hot deformation10.1016/S1006-706X(16)30041-3 ↗
11. Recovery and recrystallization in ferritic stainless steel after large strain deformation10.1016/j.msea.2005.05.057 ↗
12. The microstructure evolution and softening processes during high-temperature deformation of a 21Cr–10Ni–3Mo duplex stainless steel10.1016/j.actamat.2016.01.012 ↗
13. Dynamic recrystallization of ferrite in a low-carbon steel
14. Influence of ferrite matrix and precipitation status on the mechanical properties of low carbon low alloy steel during high temperature tension10.1016/j.msea.2016.09.058 ↗
15. Continuous dynamic recrystallization in low density steel10.1016/j.matdes.2016.10.044 ↗
16. Ferrite grain refinement in low carbon Cu–P–Cr–Ni–Mo weathering steel at various temperatures in the (α+γ) region10.1016/j.matchar.2015.12.033 ↗
17. Microstructural evolution of a 304-type austenitic stainless steel during rolling at temperatures of 773–1273K10.1016/j.actamat.2014.09.023 ↗
18. Continuous recrystallization in austenitic stainless steel after large strain deformation10.1016/S1359-6454(02)00013-7 ↗
19. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
20. A model of continuous dynamic recrystallization10.1016/S1359-6454(03)00078-8 ↗
21. Texture evolution during the recrystallization of a warm-rolled low-carbon steel10.1016/j.actamat.2006.02.050 ↗
22. On the opposition of dynamic recrystallization and solute dragging in steels10.1016/j.jallcom.2014.09.197 ↗
23. A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization10.1016/1359-6454(95)00146-7 ↗
24. The Avrami kinetics of dynamic recrystallization10.1016/j.actamat.2009.02.033 ↗
25. Flow softening of 253 MA austenitic stainless steel during hot compression at higher strain rates10.1016/j.msea.2015.10.084 ↗
26. Phenomenological model for the effect of strain rate on recrystallization and grain growth kinetics in the 617B alloy10.1016/j.jallcom.2017.11.299 ↗
27. A unified constitutive model for a low alloy steel during warm deformation considering phase differences10.1016/j.jmatprotec.2017.02.020 ↗
28. Analysis and characterisation of ultra-rine ferrite produced during a new steel strip rolling process10.1016/S1359-6462(98)00442-4 ↗
29. Mechanism of dynamic continuous recrystallization during superplastic deformation in a microduplex stainless steel10.1016/1359-6454(96)00080-8 ↗
30. Carbide precipitation in austenite of a Ti–Mo-containing low-carbon steel during stress relaxation10.1016/j.msea.2013.02.056 ↗