journal article·2016-03

Anneal hardening in cold rolled PM Cu-Au alloy

Ivana Marković, Svetlana Nestorović, Boštjan Markoli, Milena Premović, Sašo Šturm

Publisher page

Abstract

Abstract Pure copper and Cu-11.4 wt%Au alloy were obtained by a powder metallurgy (PM) technique and subjected to thermomechanical treatment that was used to produce the conditions that led to an anneal hardening effect in the alloy. The results showed that low-temperature annealing of cold-rolled alloy caused a two-stage increase in hardness, microhardness and electrical conductivity. The mechanism of anneal hardening in this alloy was studied using differential thermal analysis (DTA), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The analysis of the DTA curve showed the presence of one endothermic and three exothermic reactions during the linear heating, which confirmed the occurrence of both short-range ordering and solute segregation. A decrease in the lattice parameter of the cold-rolled αCu-Au solid solution at the annealing temperature, which corresponded to the second hardness peak, was explained by solute clustering. Formation of precipitates in the copper-based matrix during annealing was not observed by TEM. It was confirmed that the dominant hardening mechanism during annealing was solute segregation towards lattice defects.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Powder Metallurgy Techniques and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Temperature dependent flow softening of titanium alloy Ti6Al4V: an investigation using finite element simulation of machining10.1016/j.jmatprotec.2010.12.008 ↗
2. The effect of prestrain and subsequent annealing on the mechanical behavior of AA518210.1016/j.msea.2010.12.014 ↗
3. The kinetics of dynamic and static softening during multistage hot deformation of 7150 aluminum alloy10.1016/j.msea.2012.05.039 ↗
4. Deformation mechanism and softening effect of extruded AZ31 magnesium alloy sheet at moderate temperatures10.1016/S1003-6326(11)61322-8 ↗
5. Effect of annealing on microstructure evolution and mechanical property of cold forged magnesium pipes10.1016/j.matdes.2012.02.035 ↗
6. A proposed theory of anneal-hardening of cold-worked alpha brass10.2320/jinstmet1952.19.2_103 ↗
7. The mechanism of anneal hardening in dilute copper alloys10.1007/BF02811734 ↗
8. The mechanisms of anneal hardening in Cu-Al alloys10.1007/BF02644464 ↗
9. Anomalous phenomena in α phase Cu-Al binary alloys
10. Study of annealing effects on cold-worked α phase of Cu-Al alloys10.2320/matertrans1960.15.338 ↗
11. Order-strengthening in Cu-Al alloys10.1007/BF02811623 ↗
12. Effect of clusters on low temperature anneal-hardening in Cu-Fe-P dilute alloys10.2320/jinstmet.73.33 ↗
13. Improvements in properties of sintered and cast Cu-Ag alloys by anneal hardening effect10.1179/174329009X409598 ↗
14. Properties improvement and microstructure changes during thermomechanical treatment in sintered Cu-Au alloy10.1016/S1003-6326(14)63079-X ↗
15. Influence of alloying and secondary annealing on anneal hardening effect at sintered copper alloys10.1007/BF02711226 ↗
16. Nucleation and growth during recrystallization10.1590/S1516-14392005000300002 ↗
17. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
18. Annealing effects in twin-roll cast AA8006 aluminium sheets processed by accumulative roll-bonding10.3390/ma7128058 ↗
19. Long-range atomic order in irradiated Cu80Mn2010.1209/epl/i2002-00629-y ↗
20. Complex SRO isothermal kinetics in quenched Cu–12at%Mn assessed by microhardness measurements10.1016/j.msea.2005.09.061 ↗
21. Reduction of vacancy concentration during storage of severely deformed Cu10.1016/j.msea.2010.05.088 ↗
22. Effects of annealing temperature on the electrical conductivity and mechanical property of Cu-Te alloys10.1007/s11595-005-1088-0 ↗
23. Elementary model of severe plastic deformation by KoBo process10.1063/1.4861870 ↗
24. Recovery studies of neutron-irradiated and deformed Ni-Cr alloys10.1002/pssa.2211440206 ↗
25. Aging precipitation and recrystallization of rapidly solidified Cu-Cr-Zr-Mg alloy10.1016/S0921-5093(98)01149-6 ↗
26. Microstructure and creep rupture of P92-grade weld metal10.1007/BF03321294 ↗
27. Mechanical stability and electrical conductivity of Cu–Ag filamentary microcomposites10.1016/S0921-5093(98)01097-1 ↗
28. Deformation processing and strength/conductivity properties of Cu–Fe–Ag microcomposites10.1016/j.jallcom.2004.07.013 ↗
29. Modelling solute segregation to partial dislocations for DSC evaluations10.1007/BF01983434 ↗
30. Modelling the kinetics of solute segregation to partial dislocations for isothermal microcalorimetric evaluations10.1007/BF01979026 ↗
31. First-principles theory of short-range order in size-mismatched metal alloys: Cu-Au, Cu-Ag, and Ni-Au10.1103/PhysRevB.57.4332 ↗
32. Self-energy and interaction energy of stacking fault in FCC metals calculated by embedded-atom method10.1007/BF02916884 ↗
33. Direct observation of dislocation dissociation and Suzuki segregation in a Mg–Zn–Y alloy by aberration-corrected scanning transmission electron microscopy10.1016/j.actamat.2012.09.067 ↗
34. An analysis of intermetallics formation of gold and copper ball bonding on thermal aging10.1016/S0025-5408(03)00004-7 ↗
35. A molecular-dynamics study of oscillations of unclosed crystal nanostructures based on bilayer metal films10.1007/s11182-009-9282-8 ↗
36. Lattice parameter studies of annealed, of aged, and of cold worked alpha brass10.1063/1.1728750 ↗
37. Direct evidence for Suzuki segregation obtained by high-resolution analytical electron microscopy10.1080/09500839208206009 ↗
38. Suzuki segregation in a binary Cu-Si alloy10.1093/jmicro/dfh045 ↗