journal article·2018-01

Nano-twinned steel exhibits high mechanical properties obtained through ultra-rapid heat treatment

D. Fabrègue, O. Bouaziz, D. Barbier

Publisher page

Abstract

Abstract Ultra-rapid heat treatment was performed on cold rolled high manganese TWIP steel. This process obtains very high mechanical strength and good ductility through the recovery of dislocations, whereas the twins introduced during the cold rolling remain thin and stable. The maximal temperature to retain high yield strength is shown to be around 615 °C, where the first recrystallized grains appear. This heat treatment is found to provide reproducible properties across a wide temperature range and could thus open new perspectives for this type of steel. Finally, a physically based model is used to predict the yield strength resulting from ultra-rapid heat treatments.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Hadfield manganese steel
2. Supra-ductile and high-strength manganese-TRIP/TWIP for high energy absorption purposes10.2355/isijinternational.43.438 ↗
3. Cold-rolling behavior of an austenitic Fe-30Mn-3Al-3Si TWIP steel: the importance of deformation twinning10.1016/j.actamat.2003.12.040 ↗
4. Localized deformation due to Portevin–LeChatelier effect in 18Mn–0.6C TWIP austenitic steel10.2355/isijinternational.47.1804 ↗
5. High temperature flow stress and recrystallization behavior of High-Mn TWIP steels10.2355/isijinternational.47.907 ↗
6. The influence of aluminum on hot deformation behavior and tensile properties of High-Mn TWIP steels10.1016/j.msea.2007.02.074 ↗
7. Analysis of the tensile behavior of a TWIP steel based on the texture and microstructure evolutions10.1016/j.msea.2008.09.031 ↗
8. High manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships10.1016/j.cossms.2011.04.002 ↗
9. Precipitation strengthening in high manganese austenitic TWIP steels10.3139/146.110508 ↗
10. Fully recrystallized nanostructure fabricated without severe plastic deformation in high-Mn austenitic steel10.1016/j.scriptamat.2013.01.038 ↗
11. Microstructural evolution and phase transformation in twinning-induced plasticity steel induced by high-pressure torsion10.1016/j.actamat.2016.02.045 ↗
12. Identification of the parameters controlling the grain refinement of ultra-rapidly annealed low carbon Al-killed steels10.1016/j.msea.2010.05.024 ↗
13. Cold-rolling and inter-critical annealing of low-carbon steel: effect of initial microstructure and heating-rate10.1016/j.msea.2012.11.109 ↗
14. Ngansop · 2009
15. Effects of recrystallization annealing temperature on carbide precipitation, microstructure, and mechanical properties in Fe–18Mn–0.6 C–1.5 Al TWIP steel10.1016/j.msea.2009.08.048 ↗
16. Improved tensile properties of partially recrystallized submicron grained TWIP steel10.1016/j.matlet.2009.09.057 ↗
17. Damage evolution in TWIP and standard austenitic steel by means of 3D X ray tomography10.1016/j.msea.2013.05.013 ↗
18. Denis · 2008
19. Effect of process parameters on a metallurgical route providing nano-structured single phase steel with high work-hardening10.1002/adem.201100164 ↗
20. Nanostructured steel with high work-hardening by the exploitation of the thermal stability of mechanically induced twins10.1016/j.scriptamat.2009.01.004 ↗
21. The respective hardening contributions of dislocations and twins to the flow stress of a twinning-induced plasticity steel10.1016/j.scriptamat.2015.09.003 ↗
22. The effect of vacancy generation on plastic deformation
23. A model for static recrystallisation after hot deformation10.1016/0001-6160(75)90087-5 ↗
24. Dislocations, vacancies and solute diffusion in physical based plasticity model for AISI 316L10.1016/j.mechmat.2008.05.005 ↗
25. Piozin · 2014
26. Strain rate sensitivity and evolution of dislocations and twins in a twinning-induced plasticity steel10.1016/j.actamat.2015.01.013 ↗