journal article·2023-11

Flow behaviour and microstructural stability in an Al–3Mg-0.2Sc alloy processed by high-pressure torsion at different temperatures

Pedro Henrique R. Pereira, Piotr Bazarnik, Yi Huang, Malgorzata Lewandowska, Terence G. Langdon

Publisher page

Abstract

Experiments were performed to examine the flow behaviour at room temperature (RT ≈ 300 K) and the microstructural stability of a solution-treated Al-3Mg-0.2Sc alloy processed through 10 turns of high-pressure torsion (HPT) at either RT or 450 K and further annealed for 1 h at temperatures (T) up to 773 K. The results revealed that the Al-3Mg-0.2Sc alloy achieved yield strengths of ~590 and 540 MPa after HPT at RT and 450 K, respectively. This followed from the higher dislocation densities achieved after processing at RT since both microstructures had average grain diameters of ~320 nm. After annealing at T ≥ 523 K, there was evidence for the onset of dynamic strain ageing (DSA) during tensile testing at RT and this occurred concurrently with increases in the elongations to failure. The grain structures developed during HPT at 450 K exhibited superior microstructural stability than after HPT at RT for comparable heating conditions. A model derived for materials having second-phase particles was applied to understand the microstructural evolution observed during heating. It is shown that the values calculated for the driving and restraining pressures for boundary migration and the boundary stability factors are consistent with the experimental results.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. Recent development in aluminium alloys for the automotive industry10.1016/S0921-5093(99)00653-X ↗
2. Eco-friendly additive manufacturing of metals: energy efficiency and life cycle analysis10.1016/j.jmsy.2021.06.011 ↗
3. Manufacturing of lightweight components by metal forming10.1016/S0007-8506(07)60202-9 ↗
4. Tailoring a high-strength Al–4Cu alloy through processing of powders by up to 100 turns of high-pressure torsion
5. New Al–Mg–Sc alloys10.1016/S0921-5093(99)00673-5 ↗
6. Effects of cerium and zirconium microalloying addition on the microstructures and tensile properties of novel Al-Cu-Li alloys10.1016/S1875-5372(16)30147-3 ↗
7. Scandium in aluminium alloys10.1179/174328005X14311 ↗
8. Kinetics and mechanisms of precipitation in an Al-0.2wt.% Sc alloy10.1016/j.msea.2005.02.015 ↗
9. Nanoscale structural evolution of Al3Sc precipitates in Al(Sc) alloys10.1016/S1359-6454(01)00116-1 ↗
10. Composition evolution of nanoscale Al3Sc precipitates in an Al-Mg-Sc alloy: experiments and computations10.1016/j.actamat.2005.08.035 ↗
11. Enhanced grain growth in an Al-Mg alloy with ultrafine grain size10.1016/0921-5093(96)10390-7 ↗
12. An investigation of microstructural stability in an Al-Mg alloy with submicrometer grain size10.1016/1359-6454(95)00395-9 ↗
13. Influence of scandium and zirconium on grain stability and superplastic ductilities in ultrafine-grained Al-Mg alloys10.1016/S1359-6454(01)00368-8 ↗
14. Twenty-five years of ultrafine-grained materials: achieving exceptional properties through grain refinement10.1016/j.actamat.2013.08.018 ↗
15. Nanomaterials by severe plastic deformation: review of historical developments and recent advances10.1080/21663831.2022.2029779 ↗
16. Principles of equal-channel angular pressing as a processing tool for grain refinement10.1016/j.pmatsci.2006.02.003 ↗
17. Using high-pressure torsion for metal processing: fundamentals and applications10.1016/j.pmatsci.2008.03.002 ↗
18. A review on high-pressure torsion (HPT) from 1935 to 198810.1016/j.msea.2015.11.074 ↗
19. An examination of the superplastic characteristics of Al–Mg–Sc alloys after processing10.1557/jmr.2017.286 ↗
20. Influence of grain size on the flow properties of an Al-Mg-Sc alloy over seven orders of magnitude of strain rate10.1016/j.msea.2017.01.020 ↗
21. A unified approach to grain boundary sliding in creep and superplasticity10.1016/0956-7151(94)90322-0 ↗
22. Seventy-five years of superplasticity: historic developments and new opportunities10.1007/s10853-009-3780-5 ↗
23. An evaluation of the strain contributed by grain boundary sliding in superplasticity10.1016/0921-5093(94)91092-8 ↗
24. Influence of scandium on superplastic ductilities in an Al-Mg-Sc alloy10.1557/JMR.2000.0367 ↗
25. Grain refinement and superplasticity in an aluminum alloy processed by high-pressure torsion10.1016/j.msea.2004.11.007 ↗
26. Thermal stability and superplastic behaviour of an Al-Mg-Sc alloy processed by ECAP and HPT at different temperatures10.1088/1757-899X/194/1/012013 ↗
27. Examining the mechanical properties and superplastic behaviour in an Al-Mg-Sc alloy after processing by HPT10.22226/2410-3535-2015-3-294-300 ↗
28. An evaluation of the flow behavior during high strain rate superplasticity in an Al-Mg-Sc alloy
29. Influence of processing temperature on microhardness evolution, microstructure and superplastic behaviour in an Al–Mg alloy processed by high-pressure torsion10.1016/j.jmrt.2023.03.167 ↗
30. Strain induced segregations in severely deformed materials10.2320/matertrans.MF201919 ↗
31. Stabilization of nanocrystalline alloys via grain boundary segregation: a diffuse interface model10.1016/j.actamat.2015.07.058 ↗
32. Grain boundary segregation and intermetallic precipitation in coarsening resistant nanocrystalline aluminum alloys10.1016/j.actamat.2018.09.038 ↗
33. Evidence for two-stage hardening in an Al-Zn-Mg-Cu alloy processed by high-pressure torsion10.1016/j.jallcom.2023.168839 ↗
34. Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy10.1016/j.ultramic.2010.11.013 ↗
35. Examining the microhardness evolution and thermal stability of an Al–Mg–Sc alloy processed by high-pressure torsion at a high temperature10.1016/j.jmrt.2017.05.008 ↗
36. Microtexture analysis of restoration mechanisms during high pressure torsion of pure nickel10.1016/j.msea.2016.12.032 ↗
37. Formation of fully austenitic ultrafine-grained high strength state in metastable Cr-Ni-Ti stainless steel by severe plastic deformation10.1016/j.matlet.2015.12.094 ↗
38. Mechanical behavior of an Al-Mg-Mn-Sc alloy with an ultrafine grain structure at cryogenic temperatures10.1002/adem.201500138 ↗
39. Peculiar spatiotemporal behavior of unstable plastic flow in an AlMgMnScZr alloy with coarse and ultrafine grains10.3390/met7090325 ↗
40. Effect of grain refinement on jerky flow in an Al-Mg-Sc alloy10.1007/s11661-016-3381-2 ↗
41. Using finite element modeling to examine the flow processes in quasi-constrained high-pressure torsion10.1016/j.msea.2011.07.040 ↗
42. Using finite element modelling to examine the flow process and temperature evolution in HPT under different constraining conditions10.1088/1757-899X/63/1/012041 ↗
43. Developing grain refinement and superplasticity in a magnesium alloy processed by high-pressure torsion10.1016/j.msea.2007.12.046 ↗
44. An examination of the elastic distortions of anvils in high-pressure torsion10.1016/j.msea.2015.02.052 ↗
45. Mechanical properties and microstructural evolution of nanocrystalline titanium at elevated temperatures10.1016/j.msea.2016.05.105 ↗
46. Annealing-induced hardening in ultrafine-grained Ni-Mo alloys10.1002/adem.201800184 ↗
47. Achieving superior grain refinement and mechanical properties in vanadium through high-pressure torsion and subsequent short-term annealing10.1016/j.msea.2015.12.086 ↗
48. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray Debye-Scherrer spectrum10.1080/14786435608238074 ↗
49. Stacking faults in face-centred cubic metals and alloys10.1080/14786435708242709 ↗
50. Examining the thermal stability of an Al-Mg-Sc alloy processed by high-pressure torsion10.1590/1980-5373-mr-2017-0207 ↗
51. Second paper on statistics associated with the random disorientation of cubes10.1093/biomet/45.1-2.229 ↗
52. Transition from thermally assisted to mechanically driven boundary migration and related apparent activation energies10.1016/j.scriptamat.2018.05.052 ↗
53. Continuous and discontinuous grain coarsening in a fine-grained particle-containing Al–Sc alloy10.1016/j.actamat.2004.11.006 ↗
54. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
55. The cleavage strength of polycrystals
56. Seventy years of Hall-Petch, ninety years of superplasticity and a generalized approach to the effect of grain size on flow stress10.1016/j.pmatsci.2023.101131 ↗
57. Unusual behavior of the Portevin-Le Chatelier effect in an AlMg alloy containing precipitates10.1016/j.msea.2015.04.094 ↗
58. Al3(Sc,Zr)-based precipitates in Al–Mg alloy: effect of severe deformation10.1016/j.actamat.2016.10.064 ↗
59. Precipitation strengthening at ambient and elevated temperatures of heat-treatable Al(Sc) alloys10.1016/S1359-6454(02)00201-X ↗
60. Interaction of recrystallization and precipitation: the effect of Al3Sc on the recrystallization behaviour of deformed aluminium10.1016/S1359-6454(03)00002-8 ↗
61. The influence of shearable and nonshearable precipitates on the Portevin-Le Chatelier behavior in precipitation hardening AlMgScZr alloys10.1016/j.ijplas.2021.103120 ↗
62. On the addition of precipitation- and work-hardening in an Al-Sc alloy10.1016/j.msea.2006.09.164 ↗
63. Humphreys · 2004
64. Deformation mechanism maps based on grain size10.1007/BF02644014 ↗
65. Murr · 1975
66. The effect of solutes on grain boundary mobility during recrystallization and grain growth in some single-phase aluminium alloys10.1016/j.matchemphys.2011.11.018 ↗
67. Measurements of grain boundary mobility during recrystallization of a single-phase aluminium alloy10.1016/S1359-6454(99)00062-2 ↗
68. A unified theory of recovery, recrystallization and grain growth, based on the stability and growth of cellular microstructures - II. The effect of second-phase particles10.1016/S1359-6454(97)00173-0 ↗
69. Extension of the N-model to predict competing homogeneous and heterogeneous precipitation in Al-Sc alloys10.1016/S1359-6454(02)00540-2 ↗