journal article·2023-06Open access

Microstructure, properties and crystallographic orientation of novel austenitic Fe–26Mn-3.4Cr-0.4C steel under hot torsion process

Marcos Natan da Silva Lima, Guilherme Luis França Schmalz, Rodrigo de Carvalho Paes Loureiro, João Carlos Ferreira, Samuel Filgueiras Rodrigues, Jessica Calvo Muñoz, José María Cabrera Marrero, Hamilton Ferreira Gomes de Abreu

Abstract

An experimental austenitic twin-induced plasticity (TWIP) steel was deformed under hot torsion tests. Two different total equivalent strains (2.2 and 2.6) were employed in order to raise its yield strength while keeping reasonable toughness. The material was isothermally strained at 900 °C with a low strain rate of 0.05 s-1. The effects of torsional deformation on the microstructure, texture and mechanical properties of the TWIP steel were investigated and compared with the as-received samples. X-Ray Diffraction (XRD) measurements were performed to identify the phases present in the metal before and after the thermomechanical process. Scanning electron microscopy (SEM), Electron backscatter diffraction (EBSD), Orientation distribution function (ODF) analysis and tensile experiments complemented the investigation of this research. The main deformation mechanism changed from conventional sliding inside the grain to nucleated twinning from the grain boundaries, which led to the decrease of the grain size to less than 1 µm (UFG - Ultrafine Grains). The results indicate that the transition in the deformation mechanisms is dependent on grain size associated with the flow profile of the material. This was due to changes in the dislocation density within the grain and the movement of dislocations around the yield point. No martensitic transformation was detected during the strain and neither from the twinning mechanism in the microstructure after the torsion deformation. The best balance between high strength and good ductility (920 MPa and 52%) was obtained after the total equivalent strain of 2.6. It was verified that the employed thermomechanical schedule affects the displacement of the substructure with the formation of sub-grains influencing the hardening behavior, texture and yield strength of the metal.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metallurgy and Material Forming · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (87)

Show source-provided references
1. High Mn TWIP steels for automotive applications
2. Performance and characterization of TWIP steels for automotive applications
3. High manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships10.1016/j.cossms.2011.04.002 ↗
4. Study of dislocation-twin boundary interaction mechanisms in plastic deformation of TWIP steel by discrete dislocation dynamics and dislocation density-based modeling10.1016/j.ijplas.2021.103076 ↗
5. On the relationship between work hardening and twinning rate in TWIP steels10.1016/j.msea.2012.01.123 ↗
6. Strain rate dependent mechanical properties of TWIP steel
7. Hydrogen embrittlement in a Fe–Mn–C ternary twinning-induced plasticity steel10.1016/j.corsci.2011.09.022 ↗
8. Influence of cold deformation on microstructure, crystallographic orientation and tensile properties of an experimental austenitic Fe–26Mn-0.4C steel10.1016/j.jmrt.2022.05.020 ↗
9. On the effect of chemical composition on yield strength of TWIP steels10.1016/j.msea.2017.01.080 ↗
10. Precipitation strengthening in high manganese austenitic TWIP steels10.3139/146.110508 ↗
11. Interactions between deformation-induced defects and carbides in a vanadium-containing TWIP steel10.1016/j.scriptamat.2012.02.002 ↗
12. Tensile deformation behavior analysis of low density Fe–18Mn–10Al–xC steels10.1016/j.msea.2015.11.071 ↗
13. Effects of the grain size and shape on the flow stress: a dislocation dynamics study10.1016/j.ijplas.2018.09.008 ↗
14. A novel ultrafine-grained Fe 22Mn 0.6C TWIP steel with superior strength and ductility10.1016/j.matchar.2016.12.026 ↗
15. Hierarchical microstructure design of a bimodal grained twinning-induced plasticity steel with excellent cryogenic mechanical properties10.1016/j.actamat.2018.06.019 ↗
16. Applying the texture analysis for optimizing thermomechanical treatment of high manganese twinning-induced plasticity steel10.1016/j.actamat.2014.07.068 ↗
17. A novel way to enhance the strength of twinning induced plasticity (TWIP) steels10.1016/j.scriptamat.2018.05.045 ↗
18. Evolution of dislocations and twins in a strong and ductile nanotwinned steel10.1016/j.actamat.2016.03.057 ↗
19. A crystal plasticity modeling considering volume fraction of deformation twinning10.1016/j.ijplas.2016.05.002 ↗
20. Surface wrinkling of the twinning induced plasticity steel during the tensile and torsion tests10.1016/j.matdes.2014.03.063 ↗
21. Hot working of two AISI 304 steels: a comparative study10.1016/S0921-5093(02)00357-X ↗
22. Stacking fault energies of seven commercial austenitic stainless steels10.1007/BF02641927 ↗
23. A new critical point on the stress-strain curve: delineation of dynamic recrystallization from grain growth10.1016/j.matdes.2016.12.053 ↗
24. A mathematical prediction model to establish the role of stacking fault energy on the cryo-deformation behavior of FCC materials at different strain levels10.1016/j.ijplas.2017.05.014 ↗
25. Dependence of tensile deformation behavior of TWIP steels on stacking fault energy, temperature and strain rate10.1016/j.actamat.2010.05.049 ↗
26. Twinning-induced plasticity (TWIP) steels10.1016/j.actamat.2017.06.046 ↗
27. Temperature dependence of the flow stress of Fe–18Mn–0.6C–xAl twinning-induced plasticity steel10.1016/j.actamat.2013.07.042 ↗
28. Temperature dependent strain hardening and fracture behavior of TWIP steel10.1016/j.ijplas.2018.02.001 ↗
29. Tailoring extra-strength of a TWIP steel by combination of multi-pass equal-channel angular pressing and warm rolling10.3390/met11030518 ↗
30. The influence of warm rolling reduction on microstructure evolution, tensile deformation mechanism and mechanical properties of an Fe-30Mn-4Si-2Al TRIP/TWIP steel10.3390/met8100742 ↗
31. Thermomechanical behavior of biocompatible austenitic stainless steels during simulated torsion tests10.1007/s11665-019-04324-4 ↗
32. Grain size altering yielding mechanisms in ultrafine grained high-Mn austenitic steel: advanced TEM investigations10.1016/j.jmst.2021.01.031 ↗
33. Unique transition of yielding mechanism and unexpected activation of deformation twinning in ultrafine grained Fe-31Mn-3Al-3Si alloy10.1038/s41598-021-94800-6 ↗
34. Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys10.1016/j.msea.2004.01.059 ↗
35. Influence of addition elements on the stacking-fault energy and mechanical properties of an austenitic Fe–Mn–C steel10.1016/j.msea.2006.12.170 ↗
36. Ferrite Formation above the Ae3 temperature during the torsion simulation of strip rolling10.2355/isijinternational.ISIJINT-2015-320 ↗
37. Equal-channel angular pressing and annealing of a twinning-induced plasticity steel: microstructure, texture, and mechanical properties10.1016/j.actamat.2016.01.056 ↗
38. Tensile deformation behavior of Fe–Mn–C TWIP steel with ultrafine elongated grain structure10.1016/j.matlet.2012.02.012 ↗
39. Equal channel angular pressing of a TWIP steel: microstructure and mechanical response10.1007/s10853-017-0862-7 ↗
40. Twin-induced plasticity of an ECAP-processed TWIP steel10.1007/s11665-016-2400-1 ↗
41. Severe plastic deformation of a TWIP steel10.1016/j.msea.2013.11.013 ↗
42. Effects of dislocations and hydrogen concentration on hydrogen embrittlement of austenitic 316 stainless steels10.1016/j.jallcom.2021.160134 ↗
43. Diffraction-line broadening due to strain fields in materials; fundamental aspects and methods of analysis10.1107/S0108767396005727 ↗
44. The effect of dislocation contrast on x‐ray line broadening: a new approach to line profile analysis10.1063/1.117951 ↗
45. Three-dimensional analysis of grain structure and texture of additively manufactured 316L austenitic stainless steel
46. {001}⟨120⟩−{113}⟨361⟩ recrystallization textures induced by initial {001} grains and related microstructure evolution in heavily rolled electrical steel10.1016/j.matchar.2016.08.009 ↗
47. The influence of aluminum on hot deformation behavior and tensile properties of high-Mn TWIP steels10.1016/j.msea.2007.02.074 ↗
48. Contribution of intragranular misorientations to the cold rolling textures of ferritic stainless steels10.1016/j.actamat.2019.10.023 ↗
49. Mechanical, microstructural and electrical evolution of commercially pure copper processed by equal channel angular extrusion10.1016/j.msea.2013.01.076 ↗
50. The distribution of grain boundary planes in interstitial free steel10.1007/s11661-012-1393-0 ↗
51. A rationale for SRX regression model of hot-deformed austenite using an orthogonal taguchi L8 matrix steels10.4028/www.scientific.net/MSF.715-716.751 ↗
52. Effect of manganese on recrystallisation kinetics of niobium microalloyed steel10.1179/026708302225001859 ↗
53. Texture evolution in equal-channel angular extrusion10.1016/j.pmatsci.2009.01.001 ↗
54. Evolution of crystallographic texture during equal channel angular extrusion of copper: the role of material variables10.1007/s11661-006-0046-6 ↗
55. Texture and fatigue behavior of ultrafine grained copper produced by ECAP10.1016/j.msea.2014.05.011 ↗
56. Torsion texture measurements with high-energy synchrotron radiation on NiAl10.1080/07303300310001628733 ↗
57. Role of twinning on texture evolution of silver during equal channel angular extrusion10.1080/14786430601003866 ↗
58. Characterization and prediction of flow behavior in high-manganese twinning induced plasticity steels: Part I. Mechanism maps and work-hardening behavior10.1007/s11661-011-0993-4 ↗
59. Evolution of crystallographic texture during equal channel angular extrusion of silver10.1016/j.scriptamat.2003.08.011 ↗
60. Texture evolution during room temperature ageing of silver processed by equal-channel angular pressing10.1016/j.scriptamat.2011.02.005 ↗
61. On the mechanism of twin formation in Fe–Mn–C TWIP steels10.1016/j.actamat.2009.12.032 ↗
62. TSL-OIM v5.2 User's Manual, EDAX Inc., Mahwah, NJ, (n.d).
63. Evolution of crystallographic texture and microstructure during cold rolling of twinning-induced plasticity (TWIP) steel: experiments and simulations10.1007/s11661-012-1346-7 ↗
64. The damping behavior of Ni added Mn-Cu damping alloys10.2320/matertrans.44.1671 ↗
65. Analysis of the early stage of stress corrosion cracking in austenitic stainless steel by EBSD and XRD10.1016/j.matchar.2021.110882 ↗
66. XRD and EBSD analysis of anisotropic microstructure development in cold rolled F138 stainless steel10.1016/j.matchar.2016.11.018 ↗
67. Twinning behaviour of TWIP steel studied by Taylor factor analysis10.1080/09500839.2013.776185 ↗
68. Multi-scale correlative microscopy investigation of both structure and chemistry of deformation twin bundles in Fe–Mn–C steel10.1017/S1431927613013494 ↗
69. Dynamic recrystallization based on twinning in coarse-grained Mg10.4028/www.scientific.net/MSF.419-422.521 ↗
70. Misorientation-dependent twinning induced hardening and texture evolution of TWIP steel sheet in plastic deformation process10.3390/met7090348 ↗
71. Effects of Al addition on tensile properties of partially recrystallized austenitic TRIP/TWIP steels10.1016/j.msea.2021.140823 ↗
72. Improvement of low-cycle fatigue resistance in TWIP steel by regulating the grain size and distribution10.1016/j.actamat.2017.05.004 ↗
73. Simultaneous improvement of strength and plasticity: additional work-hardening from gradient microstructure10.1016/j.actamat.2017.12.028 ↗
74. Serrated plastic flow10.1007/BF02743993 ↗
75. The portevin-le chatelier effect. A kinetic theory10.1016/0001-6160(84)90129-9 ↗
76. Modeling the deformation textures and microstructural evolutions of a Fe–Mn–C TWIP steel during tensile and shear testing10.1016/j.msea.2012.01.128 ↗
77. Effects of Cr addition on Charpy impact energy in austenitic 0.45C-24Mn-(0,3,6)Cr steels10.1016/j.jmst.2019.12.032 ↗
78. Comparative studies on microstructure evolution and corrosion resistance of 304 and a newly developed high Mn and N austenitic stainless steel welded joints10.1016/j.corsci.2021.109338 ↗
79. Structural and phase transformation in a TWIP steel subjected to high pressure torsion10.1016/j.matlet.2015.12.095 ↗
80. Outstanding mechanical properties of high-pressure torsion processed multiscale TWIP-cored three layer steel sheet10.1016/j.scriptamat.2016.06.009 ↗
81. Stacking fault energy and microstructure effects on torsion texture evolution10.1098/rspa.2000.0543 ↗
82. Strain hardening behavior of a Fe–18Mn–0.6C–1.5Al TWIP steel10.1016/j.msea.2009.08.028 ↗
83. Analysis of the tensile behavior of a TWIP steel based on the texture and microstructure evolutions10.1016/j.msea.2008.09.031 ↗
84. Effect of ECAP processing temperature on an austenitic TWIP steel's microstructure, texture and mechanical properties10.1016/j.jmrt.2023.03.116 ↗
85. Outstanding tensile properties and their origins in twinning-induced plasticity (TWIP) steels with gradient substructures10.3390/ma13051184 ↗
86. Influence of nanotwins on hydrogen embrittlement of TWIP (twinning-induced plasticity) steel processed by high-pressure torsion10.1016/j.msea.2020.139273 ↗
87. Role of vanadium additions on tensile and cryogenic-temperature charpy impact properties in hot-rolled high-Mn austenitic steels10.1016/j.msea.2021.141063 ↗