journal article·2019-09

Acceleration of diffusional transformation in a high-carbon steel layer composed of a sandwich-like clad steel sheet

Rintaro Ueji, Tadanobu Inoue

Publisher page

Abstract

Abstract The thermomechanical interactions between two different regions with different carbon contents during cooling from the austenite single phase condition was studied with a sandwich-like clad sheet. The clad steel with a layered structure where a 0.65%C high-carbon steel sheet was sandwiched by 0.05%C low-carbon steel sheets was prepared. The benefit of this clad structure for this study is that any fraction of the composed layers can be fabricated artificially with the constant carbon content in both component layers. In the experiments, the clad sheets were prepared by plain strain compression at 900 °C for welding, followed by gas quenching. The microstructural observation revealed that the fraction of the martensite structure in the high-carbon steel layer decreased and, alternatively, a pearlite structure evolved as the fraction of the low-carbon steel layers was increased; whereas the low-carbon steel layers showed ferrite and pearlite structures with any construction of the clad steel. Consequently, the hardness of the high-carbon steel layer decreased in the sheet with the higher fraction of low-carbon steel layers. The reason for this change is due to both the elastic strain and the plastic deformation of the high-carbon steel layer induced by phase transformation in the low-carbon layers.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Metallurgical aspects in cold rolled high strength steel sheets10.1007/BF02641975 ↗
2. Influence of martensite composition and content on properties of dual phase steels10.1007/BF02659924 ↗
3. Early stages of yielding and strain aging of a vanadium-containing dual-phase steel10.1007/BF02812021 ↗
4. Effect of boron on the microstructure and tensile properties of dual-phase steel10.1007/BF02647000 ↗
5. Influence of silicon on the microstructures, mechanical properties and stretch-flangeability of dual phase steels10.1007/s12613-014-0968-8 ↗
6. Carbon partitioning into austenite after martensite transformation10.1016/S1359-6454(03)00059-4 ↗
7. Individual phase constitutive properties of a TRIP-assisted QP980 steel from a combined synchrotron X-ray diffraction and crystal plasticity approach10.1016/j.actamat.2017.04.028 ↗
8. Local orientation change inside lenticular martensite plate in Fe-33Ni alloy10.1016/j.scriptamat.2005.04.023 ↗
9. Relation between martensite morphology and volume change accompanying fcc to bcc martensite transformation in Fe-Ni-Co alloys10.1016/j.msea.2005.12.044 ↗
10. Reducing vehicle weight and improving U.S. energy efficiency using integrated computational materials engineering10.1007/s11837-012-0424-z ↗
11. Nature-inspired hierarchical steels10.1038/s41598-018-23358-7 ↗
12. Simultaneous improvement of strength and plasticity: additional work-hardening from gradient microstructure10.1016/j.actamat.2017.12.028 ↗
13. Effect of interface morphology on tensile properties of carbon steel sheet with sandwich structure10.1002/srin.201900015 ↗
14. The history of the metallographic study of the Japanese sword10.1016/S1044-5803(01)00101-2 ↗
15. Ancient and modern laminated composites— from the Great Pyramid of Gizeh to Y2K10.1016/S1044-5803(00)00077-2 ↗
16. Development of multilayer steels for improved combinations of high strength and high ductility10.2320/matertrans.M2013382 ↗
17. Fracture elongation of brittle/ductile multilayered steel composites with a strong interface10.1016/j.scriptamat.2008.07.020 ↗
18. The morphology and crystallography of lath martensite in Fe-C alloys10.1016/S1359-6454(02)00577-3 ↗
19. Crystallographic orientation rotation and internal stress in pearlite colony10.1016/j.scriptamat.2009.03.028 ↗
20. Martensite in steel: strength and structure10.1016/S0921-5093(99)00288-9 ↗
21. The effect of morphology on the strength of pearlite10.1007/BF02642832 ↗
22. TRIP aided deformation of a near-Ni-free, Mn-N bearing duplex stainless steel10.1016/j.msea.2011.12.037 ↗
23. Effect of initial grain size on inhomogeneous plastic deformation and twinning behavior in high manganese austenitic steel with a polycrystalline microstructure
24. Specific heat of high purity iron by a pulse heating method10.1063/1.1735393 ↗
25. Finite element simulation of quench distortion in a low-alloy steel incorporating transformation kinetics10.1016/j.actamat.2007.11.039 ↗
26. Elastic properties of ferrite and austenite in low alloy steels versus temperature and alloys10.1016/j.mtla.2018.100193 ↗
27. Influence of stresses on the kinetics of pearlitic transformation during continuous cooling10.1016/0001-6160(87)90109-X ↗
28. Effect of applied tensile stress on phase transformations in steel10.1016/0001-6160(59)90031-8 ↗
29. Nature of dynamic ferrite transformation revealed by in-situ neutron diffraction analysis during thermomechanical processing10.1016/j.scriptamat.2019.02.017 ↗