journal article·2022-01Open access

Revisiting copper as a case study of creep in pure metals: Prediction of creep response in pure Cu in half-hard and friction-stir-processed states

C. Paoletti, E. Santecchia, M. Cabibbo, M. Regev, S. Spigarelli

Abstract

Abstract A physical model was used to obtain a pre-assessment of the dependence of minimum creep rate on stress and temperature for ETP copper under two different initial conditions, i.e., in the R240 half-hardened state and after friction stir processing. Although the R240 samples contained a high dislocation density owing to pre-straining, the material that underwent friction stir processing (FSP) had a much finer grain size and a far lower dislocation density. The original Sandstrom physically based model developed for copper was modified to take into account the strengthening role of the grain boundaries, and its declining importance with increasing temperature and/or decreasing applied stress. In addition, the grain growth effect was estimated using appropriate empirical equations. The model curves obtained by introducing a few initial information, such as the grain size and the ultimate tensile strength at room temperature, in the resulting set of constitutive equations, largely overlapped. This finding was somewhat in conflict with the traditional view, which assumes that a fine grain size is an ineffective source of creep strengthening, if not detrimental. Subsequent creep experimental testing carried out between 178 and 355 °C substantially confirmed the picture provided by the pre-assessment, and the minimum creep rate values for the two materials largely overlapped on the same curves. Only at 355 °C did the FSP samples exhibit a somewhat higher creep rate, when compared with the R240 samples and the pre-assessment curve. The experimental data obtained for R240 copper at 475 °C were not properly described by the physical model, as expected on the basis of the previous literature reports.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. Creep of annealed and cold-drawn high-purity copper10.6028/jres.047.035 ↗
2. Mechanical behavior of crystalline solids at elevated temperature10.1016/0079-6425(68)90024-8 ↗
3. Creep behavior of copper at intermediate temperatures-I. Mechanical characteristics10.1016/0001-6160(89)90011-4 ↗
4. Creep behavior of copper at intermediate temperatures-II. Surface microstructural observations10.1016/0956-7151(91)90150-Y ↗
5. Creep behavior of copper at intermediate temperatures-III. A comparison with theory10.1016/0956-7151(91)90151-P ↗
6. What is “stationary” deformation of pure Cu?10.1007/s10853-013-7983-4 ↗
7. The effect of phosphorus on creep in copper10.1016/j.jnucmat.2007.02.004 ↗
8. Creep in phosphorus alloyed copper during power-law breakdown10.1016/j.jnucmat.2007.02.005 ↗
9. Basic model for primary and secondary creep in copper10.1016/j.actamat.2011.09.052 ↗
10. Influence of phosphorus on the tensile stress strain curves in copper10.1016/j.jnucmat.2015.12.024 ↗
11. Modeling of tertiary creep in copper at 215 and 250 °C10.1115/1.4049241 ↗
12. Five-power-law creep in single phase metals and alloys10.1016/S0079-6425(99)00006-7 ↗
13. Creep and creep fracture of polycrystalline copper10.1016/j.msea.2006.08.094 ↗
14. Monovacancies and divacancies in copper10.1016/S0921-4526(99)00209-4 ↗
15. High strain rate superplasticity in a friction stir processed 7075 Al alloy10.1016/S1359-6462(99)00329-2 ↗
16. Development of high strength, high conductivity copper by friction stir processing10.1016/j.matdes.2010.08.028 ↗
17. Evaluation of tensile deformation properties of friction stir processed pure copper: effect of processing parameters and pass number10.1007/s11665-013-0734-5 ↗
18. Friction stir processed copper : a review
19. Role of friction stir processing on copper and copper based particle reinforced composites – a review
20. Twenty-year uninterrupted endeavor of friction stir processing by focusing on copper and its alloys10.1016/j.jallcom.2018.12.083 ↗
21. Hall-Petch analysis for temperature and strain rate dependent deformation of polycrystalline lead10.1134/S1029959916010045 ↗
22. 60 years of hall-petch: past to present nano-scale connections10.2320/matertrans.MA201302 ↗
23. Tensile deformation of high-purity copper as a function of temperature, strain rate, and grain size10.1016/0001-6160(53)90022-4 ↗
24. On the enhanced grain growth in ultrafine grained metals10.1016/0956-7151(95)00087-C ↗
25. Thermal stability of ultrafine grained pure copper prepared by large strain extrusion machining10.3390/met8060381 ↗
26. Grain growth in copper and alpha-brasses10.1007/BF01129942 ↗
27. Grain growth in copper
28. Kaur · 1989
29. Grain boundary self-diffusion in Cu polycrystals of different purity10.1016/S1359-6454(97)00037-2 ↗
30. Basic creep modelling of Aluminium10.1016/j.msea.2017.11.053 ↗
31. Experimental evaluation of the Peierls stresses in a variety of crystals and their relation to the crystal structure10.1016/j.actamat.2012.09.059 ↗
32. Strain rate and temperature dependence of the flow stress of copper-manganese dilute alloy single crystals10.2320/jinstmet1952.32.4_385 ↗
33. A study of the metallurgical and mechanical properties of friction-stir-processed cu10.3390/met11040656 ↗
34. On monitoring mechanical characteristics of rolled electrolytic copper10.1016/j.prostr.2016.06.290 ↗
35. Microstructure and mechanical properties of pure copper subjected to skin pass asymmetric rolling10.1051/matecconf/201818500003 ↗
36. Evolution of dislocation density distributions in copper during tensile deformation10.1016/j.actamat.2013.08.027 ↗
37. Measurement of screw and edge dislocation density by means of X-ray Bragg profile analysis10.1016/S0921-5093(01)00979-0 ↗
38. Tensile properties of copper, nickel, and 70-percent-copper-30-percent-nickel and 30-percent-copper-70-percent-nickel alloys at high temperatures10.6028/jres.058.027 ↗
39. Electrolytic though-pitch copper Cu-ETP, data sheet No. A1, cons
40. Grain size effects during creep of copper10.1016/S1359-6462(01)01247-7 ↗
41. The characteristics of creep in metallic materials processed by severe plastic deformation10.2320/matertrans.MF201924 ↗
42. Enhanced creep properties of copper and its alloys processed by ECAP10.1088/1757-899X/63/1/012141 ↗
43. Effect of grain refinement by ECAP on creep of pure Cu10.1016/j.msea.2013.10.022 ↗
44. On the effect of atoms in solid solution on grain growth kinetics10.1007/s11661-014-2459-y ↗
45. New trends in creep microstructural models for pure metals10.1051/rphysap:01987002203016900 ↗
46. Initiation of dynamic recrystallization under inhomogeneous stress states in pure copper10.1016/S1359-6454(99)00313-4 ↗
47. Dynamic recrystallization of Cu single crystals during tensile deformation in creep10.1179/030634583790420565 ↗
48. Role of Cu2O during hot compression of 99.9% pure copper10.1016/j.msea.2007.10.079 ↗
49. Modelling the hot flow stress of commercial purity coppers with different oxygen levels10.4028/www.scientific.net/MSF.426-432.3921 ↗
50. The role of creep in stress strain curves for copper10.1016/j.jnucmat.2011.12.012 ↗
51. The role of cell structure during creep of cold worked copper10.1016/j.msea.2016.08.004 ↗