The effects of induction quenching and pre-strain levels on twin behavior in extruded ZK21 magnesium alloy
Source abstract
Abstract
Abstract In the present study, pre-compressive test, re-compressive test or reverse tensile test were carried out on the extruded ZK21 alloy to investigate the twinning and detwinning behaviors after induction quenching. The influence of quenching temperature and the pre-strain levels on mechanical behavior was systematically addressed. It is found that the growth and shrinkage of the previous twins generated by pre-compression are impeded for all samples after quenching and the extent of twin growth or shrinkage is closely related to the pre-strain levels. Induction quenching has little influence on twin nucleation during recompression, while the number of new nucleated twins decreases dramatically with the increase of pre-strain levels for all the samples. Meanwhile, our results also show that quenching temperature and pre-strain levels generate quite different effects on the re-compressive yield strength and the reverse tensile yield strength. Correspondingly, the influence of twin behavior on mechanical properties was discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Internal stress relaxation and load redistribution during the twinning–detwinning-dominated cyclic deformation of a wrought magnesium alloy, ZK60A10.1016/j.actamat.2008.04.006 ↗
2. The dislocation-twin interaction and evolution of twin boundary in AZ31 Mg alloy10.1016/j.actamat.2017.05.034 ↗
3. Enhancing plastic deformability of Mg and its alloys – a review of traditional and nascent developments10.1016/j.jma.2017.11.001 ↗
4. Deformation twinning in AZ31: influence on strain hardening and texture evolution10.1016/j.actamat.2010.07.041 ↗
5. Tailoring the texture of magnesium alloy by twinning deformation to improve the rolling capability10.1016/j.scriptamat.2011.02.010 ↗
6. The role of strain accommodation during the variant selection of primary twins in magnesium10.1016/j.actamat.2010.12.005 ↗
7. Intragranular twinning, detwinning, and twinning-like lattice reorientation in magnesium alloys10.1016/j.actamat.2016.08.058 ↗
8. Study of twinning behaviors of rolled AZ31 magnesium alloy by interrupted in situ compressive tests10.1016/j.msea.2015.12.011 ↗
9. Effect of indentation size on the nucleation and propagation of tensile twinning in pure magnesium10.1016/j.actamat.2015.04.005 ↗
10. Recent research and developments on wrought magnesium alloys10.1016/j.jma.2017.09.001 ↗
11. Detwinning behavior of Mg–3Al–1Zn alloy at elevated temperatures10.1016/j.msea.2014.08.034 ↗
12. Dependence of compressive deformation on pre-strain and loading direction in an extruded magnesium alloy: texture, twinning and de-twinning10.1016/j.msea.2013.12.038 ↗
13. In situ investigation of extension twinning-detwinning and its effect on the mechanical behavior of AZ31B magnesium alloy10.1016/j.matdes.2017.06.023 ↗
14. Direct observation of twinning–detwinning–retwinning on magnesium single crystal subjected to strain-controlled cyclic tension–compression in [0 0 0 1] direction10.1080/09500839.2011.617713 ↗
15. Periodic segregation of solute atoms in fully coherent twin boundaries10.1126/science.1229369 ↗
16. Designing Mg alloys with high ductility: reducing the strength discrepancies between soft deformation modes and hard deformation modes10.1016/j.actamat.2017.09.006 ↗
17. Annealing strengthening in a dilute Mg–Zn–Ca sheet alloy10.1016/j.scriptamat.2015.06.002 ↗
18. Enhancing the effect of texture control using {101¯2} twins by retarding detwinning activity in rolled Mg–3Al–1Zn alloy10.1016/j.scriptamat.2013.09.002 ↗
19. Impact of solute elements on detwinning in magnesium and its alloys10.1016/j.ijplas.2016.09.014 ↗
20. Failure analysis of forged and induction hardened steel cold work rolls10.1016/j.engfailanal.2003.11.005 ↗
21. Influence of process parameters for induction hardening on residual stresses10.1016/S0261-3069(01)00033-4 ↗
22. Experimental investigation on the mechanical behavior of high-frequency induction-hardened mild carbon, SPS5 steel10.1016/j.msea.2007.07.088 ↗
23. The influences of chromium addition and quenching treatment on the mechanical properties and fracture behaviors of diffusion-alloyed powder metal steels10.1016/j.msea.2012.12.032 ↗
24. Dislocation density based model for Al-Cu-Mg alloy during quenching with considering the quench-induced precipitates
25. Effect of quench-induced precipitation on microstructure and mechanical properties of 7085 aluminum alloy10.1016/j.matdes.2017.06.054 ↗
26. The different effects of solute segregation at twin boundaries on mechanical behaviors of twinning and detwinning10.1016/j.msea.2015.07.049 ↗
27. A constitutive model of twin nucleation, propagation and growth in magnesium crystals10.1016/j.msea.2014.11.096 ↗
28. Vacancy–Mg complexes and their evolution in early stages of aging of Al–Mg based alloys10.1016/j.apsusc.2014.01.078 ↗
29. Investigating the effect of as-quenched vacancies in the final microstructure of 1.2080 tool steel during the deep cryogenic heat treatment10.1016/j.matlet.2012.11.081 ↗
30. Characterization of quenched-in vacancies in Fe–Al alloys10.1016/j.physb.2011.12.122 ↗
31. Strengthening and microstructure modification associated with moving twin boundaries in hcp metals10.1080/09500830701244812 ↗
32. Regulating twin boundary mobility by annealing in magnesium and its alloys10.1016/j.ijplas.2017.08.002 ↗
33. The role of dislocations in strain hardening of an extension twinning predominant deformation10.1016/j.msea.2015.04.007 ↗
34. A new annealing hardening mechanism in pre-twinned Mg–3Al–1Zn alloy10.1016/j.msea.2015.12.046 ↗