The development and characterization of ultra high GIGA-strength ferritic hot band steels
Source abstract
Abstract
Abstract The correlations existing among the hot mill processing, as-coiled microstructure and mechanical properties of a Mo–Ti–V microalloyed hot rolled high strength steel were investigated in this current study. Discrete processing parameters, i.e., finish rolling temperatures (FRT) and coiling temperatures (CT), were applied and the corresponding microstructures and mechanical properties were analyzed. It was found that the FRT had only a very minor influence on either microstructures or mechanical properties. However, the CTs strongly affected both the microstructures and mechanical properties. The microstructure in the matrix was observed to change from mainly polygonal ferrite to quasi-polygonal ferrite to granular bainite and upper bainite with falling CTs, accompanied by the formation of martensite/austenite (M/A) constituents at the lower CTs. The strength appeared to be increased by the dislocations originating by the shear component of the displacive phase transformation, and by fine (Ti, Mo)C precipitates, both formed during the coiling process. Strengths reaching values as high as 1166 MPa in yield strength and 1225 MPa in tensile strength were observed in specimens after coiling at 610 °C, and the steels still had a reasonable total elongation of around 20%. However, the hole expansion ratios of these steel conditions were rather low in this study, especially for those with higher strength. Several factors appeared to contribute to the poor hole expansion ratios found in these steel conditions: the presence of coarse TiN inclusions, a large amount of strengthening precipitates and a high dislocation density as well as the presence of M/A constituents.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Magnetic Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. New high strength steels applied to the body structure of ULSAB-AVC
2. Advanced high strength steels for automotive industry10.3989/revmetalm.1158 ↗
3. Advanced high strength steels for automotive industry10.1016/S1644-9665(12)60197-6 ↗
4. The partnership for a new generation of vehicles (PNGV) and its impact on body engineering
5. New car-new materials10.1016/S0261-3069(97)00049-6 ↗
6. Influence of martensite morphology on sheared-edge formability of dual-phase steels10.2355/isijinternational.ISIJINT-2016-602 ↗
7. Microstructure and precipitation behavior of Nb, Ti bomplex microalloyed steel produced by compact strip processing10.2355/isijinternational.46.1345 ↗
8. On strength of microalloyed steels: an interpretive review10.1179/174328409X455233 ↗
9. Effect of vanadium and titanium modification on the microstructure and mechanical properties of a microalloyed HSLA steel10.1016/j.msea.2009.10.049 ↗
10. Hole expansion of dual phase steels10.2495/HPSM120071 ↗
11. Em Totten · 2003
12. Shimizu · 2004
13. Nissan to Use Ultrastrong · 2018 · 1
14. Advanced high stretch-flange formability steels for chassis & suspension applications
15. Sheared-edge ductility/hole-expansion ratio testing of advanced high-strength steels
16. 2003
17. Morphological aspects of martensite–austenite constituents in intercritical and coarse grain heat affected zones of structural steels10.1016/S0921-5093(04)00859-7 ↗
18. Effects of martensnite-austennite on HAZ toughness of a high strength steel
19. Ferritic microstructures
20. The proeutectoid ferrite and the proeutectoid cementite reactions
21. Morphology and properties of low-carbon bainite10.1007/BF02656571 ↗
22. A perspective on the morphology of bainite10.1007/BF02656565 ↗
23. Araki · 1992
24. The γ→ α transformation in low carbon irons10.2355/isijinternational.34.615 ↗
25. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
26. A Study of the batch annealing of cold-rolled HSLA steels containing niobium or titanium10.1007/s11661-015-2949-6 ↗
27. Analysis of grain misorientation distribution in polygonal ferrite of low-carbon steel10.1016/j.matchar.2016.10.022 ↗
28. Conditions for the occurrence of acicular ferrite transformation in HSLA steels10.1007/s10853-017-1781-3 ↗
29. Transformation behavior and microstructural characteristics of acicular ferrite in linepipe steels10.1016/j.msea.2007.06.035 ↗
30. Gladman · 1997
31. Processing characteristics and properties of Ti–V–N steels
32. The effect of titanium and nitrogen contents on the austenite grain coarsening temperature10.1007/BF00660940 ↗
33. Solubility product of TiN in austenite10.2355/isijinternational.38.991 ↗
34. Reassessment of the solubility of TiC and TiN in Fe10.2355/isijinternational.39.84 ↗
35. Ma · 2017
36. Grain-refined C-Mn steels
37. Role of vanadium in microalloyed steels
38. Influence of processing factors on the sheared-edge formability of vanadium bearing dual-phase steels produced using continuous galvanizing line simulations10.1007/s10853-020-04385-0 ↗
39. Dieter · 1986 · 197
40. Leslie · 1981 · 134
41. Dislocation theory of yielding and strain ageing of iron10.1088/0370-1298/62/1/308 ↗
42. Early stages of yielding and strain aging of a vanadium-containing dual-phase steel10.1007/BF02812021 ↗
43. Effect of finish rolling temperature on the structure and properties of directly quenched Nb containing low carbon steel10.1007/BF02814349 ↗
44. Yong · 2006 · 83
45. Microstructure, precipitate and property evolution in cold-rolled Ti V high strength low alloy steel
46. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
47. Generalization of the existing relations between microstructure and yield stress from ferrite–pearlite to high strength steels10.1016/j.msea.2012.10.012 ↗
48. Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues10.1016/S1359-6462(02)00335-4 ↗
49. Analysis of complex steel microstructures by high-resolution EBSD
50. Ashby · 1971
51. Non-linear correlation between uniaxial tensile properties and shear-edge hole expansion ratio10.1007/s11665-014-1161-y ↗
52. Factors governing hole expansion ratio of steel sheets with smooth sheared edge10.1007/s12540-016-6346-5 ↗
53. Effects of microstructure on stretch-flange-formability of 980 MPa grade cold-rolled ultra high strength steel sheets10.2355/isijinternational.44.603 ↗
54. Failure during sheared edge stretching of dual-phase steels10.1007/s11661-013-1718-7 ↗
55. Damage evolution in complex-phase and dual-phase steels during edge stretching10.3390/ma10040346 ↗