journal article·2017-03

A comparison between 2017A and 4047A aluminum alloys microstructure changes under thermal fatigue loading

Adel Belkharchouche, Achraf Boudiaf, Mohamed El Amine Belouchrani

Publisher page

Abstract

Abstract This paper presents a study of 2017A and 4047A aluminum alloys microstructure changes under thermal fatigue loading. Specimens were subjected to a cyclic thermal load. The thermal fatigue loading is ensured by applying repetitive heating and cooling cycles; with a temperature variation between 80 and 280 °C using a lab-made bench test. Only thermal loading was considered. No mechanical stress was applied during all tests. Change in mechanical properties of the tested materials was studied through hardness measurements, SEM micrographic observations and XRD analysis for different cycle numbers. For the two alloys, the results showed that the hardness decreases when the cycle number increases. This observed phenomenon is more important in the case of 2017A alloy. Micrographic observation and XRD analysis led to conclude that this hardness decrease is due to the dispersion and morphology changes of the hardening precipitates, for the 2017A alloy, and silicon particles dissolution in case of the 4047A alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · High Temperature Alloys and Creep · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. Thermal fatigue loading for a type 304-L stainless steel used for pressure water reactor: investigations on the effect of a nearly perfect biaxial loading, and on the cumulative fatigue life10.1016/j.proeng.2010.03.172 ↗
2. Thermal shock and thermal fatigue study of alumina10.1016/S0955-2219(02)00022-5 ↗
3. Analyzing the mechanisms of thermal fatigue and phase change of steel used in brake discs10.1016/j.engfailanal.2015.07.002 ↗
4. Thermal fatigue analysis of automotive Diesel piston: experimental procedure and numerical protocol10.1016/j.ijfatigue.2014.11.011 ↗
5. High cycle fatigue damage mechanisms in cast aluminium subject to complex loads10.1016/j.ijfatigue.2012.07.008 ↗
6. Influence of temperature on cyclic stress response, strain resistance, and fracture behavior of aluminum alloy 252410.1016/S0921-5093(00)01912-2 ↗
7. Low cycle thermal fatigue of aluminum alloy cylinder head in consideration of changing metrology microstructure10.1016/j.proeng.2010.03.083 ↗
8. High and low-cycle fatigue influence of silicon, copper, strontium and iron on hypo-eutectic al–si–cu and al–si–mg cast alloys used in cylinder heads10.1016/j.ijfatigue.2015.09.015 ↗
9. Measurements and predictions of steady- state and transient stress distributions in a diesel engine cylinder head
10. Low cycle thermal fatigue and microstructural change of AC2B − T6 aluminum alloy10.1016/j.ijfatigue.2005.06.025 ↗
11. Precipitation and age-hardening in Al − Si − Cu − Mg − Fe casting alloys10.4028/www.scientific.net/MSF.217-222.777 ↗
12. Effects of constituent particle clusters on fatigue behavior of 2024−T3 aluminum alloy10.1016/S0142-1123(98)00041-3 ↗
13. Al–Si cast alloys under isothermal and thermomechanical fatigue conditions10.1016/j.ijfatigue.2007.01.006 ↗
14. Effect of microstructural constituents on the thermal fatigue life of (A319) aluminum alloy10.1016/j.msea.2007.01.018 ↗
15. X. Zhu, A. Shyam, J. Jones, H. Mayer, J. Lasecki, J. Allison, Effects of microstructure and temperature on fatigue behavior of E319 – T7 cast aluminum alloy in very long life cycles, Int. J.Fatigue 28(11) 1566–1571, in: Proceedings of the third International Conference on Very High Cycle Fatigue (VHCF-3)Third International Conference on Very High Cycle Fatigue, 2006.10.1016/j.ijfatigue.2005.04.016 ↗
16. The effect of solidification time and heat treatment on the fatigue properties of a cast 319 aluminum alloy10.1007/s11661-003-0147-4 ↗
17. Heat treatment effect on thermo-mechanical fatigue and low cycle fatigue behaviors of A3560.0 aluminum alloy10.1016/j.matdes.2012.08.066 ↗
18. Microporosity control and thermal-fatigue resistance of (A319) aluminum foundry alloy10.1016/j.msea.2007.03.031 ↗
19. Temperature effects on counterion binding to spherical polyelectrolytes: the charge-discharge transition of lignosulfonate10.1016/0302-4598(95)01814-U ↗