Characterisation of elastic-plastic material characteristics of Sn solid solution, SbSn and Cu6Sn5 in the tin-based sliding bearing alloy SnSb12Cu6ZnAg
Source abstract
Abstract
Abstract In order to allow the stress calculation for the structure of dynamically stressed tin-based alloys for plain bearings, knowledge about the material behaviour of the structural constituents of the alloy is required. The individual microstructural phases of the alloy SnSb12Cu6ZnAg were identified in Energy Dispersive X-ray Spectroscopy (EDX) analyses. The phases are the Sn solid solution, antimony-tin precipitates (SbSn), and copper-tin precipitates (Cu6Sn5). Nano-indent measurements were performed and evaluated in a phase-specific manner. Thus, the elastic-plastic material characteristics could be determined for each phase. For the calculation of the characteristic values from the measurement results, different approaches as well as the influence of the variation in correction factors were considered. Furthermore, finite element (FE) simulations of the nano-indentations were performed and the validity of the calculated material parameters was tested. It was shown that owing to phenomena such as pile-up or residual roughness, the calculated values deviated from simulated ones. Consideration of the elastic-plastic deformations of the sample on the indenter tip in the calculations led to results with the least deviation from those obtained from the FE simulations. A comparison of the calculated material values to those documented in the literature resulted in a satisfactory agreement, which was within the expected uncertainties of the underlying calculation approaches. Only for the tin-rich solid solution could the validity of the derived material characteristics not be ensured. An evaluation of the increase in the load-bearing capacity of the alloy as whole by means of the precipitates revealed that a minimal increase by a factor of 2.6 was possible.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electronic Packaging and Soldering Technologies · Metal and Thin Film Mechanics · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. International Standard Organisation · 2013
2. Stabilisation of Cu6Sn5 by Ni in Sn-0.7Cu-0.05Ni lead-free solder alloys10.1016/j.intermet.2009.07.005 ↗
3. W. Hilgers, Gleitlagerwerkstoffe, in: Th. Goldschmidt (Ed.), Gleitlagertechnik, Th. Goldschmidt AG, Essen, 1992, pp. 7–25.
4. ECKA Granulate GmbH & Co. KG, Gleitlagerlegierung ECKA TEGOSTAR, ECKA Granulate GmbH & Co. KG, Essen, 2012, pp. 1–2.
5. A method for interpreting the data from depth-sensing indentation instruments10.1557/JMR.1986.0601 ↗
6. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
7. Measurement of hardness and elastic modulus by instrumented indentation10.1557/jmr.2004.19.1.3 ↗
8. Computational modeling of the forward and reverse problems in instrumented sharp indentation10.1016/S1359-6454(01)00295-6 ↗
9. Micro-hardness of annealed and work-hardened copper polycrystals10.1016/1359-6462(95)00524-2 ↗
10. Deformation behavior of (Cu, Ag)–Sn intermetallics by nanoindentation10.1016/j.actamat.2004.05.046 ↗
11. Anton Paar GmbH, Instrumented Indentation Testers, in: Anton Paar GmbH (Ed.), Mechanical Characterization of Materials, Graz, 2016.
12. The effect of indenter angle on the microindentation hardness10.1016/j.actamat.2007.07.016 ↗
13. Modeling of nanoindentation of bulk and thin film by finite element method10.1016/j.wear.2004.05.021 ↗
14. Simulation of instrumented indentation and material characterization10.1016/j.msea.2004.08.037 ↗
15. N. Conté, Anton Paar, S.A. TriTec, Advanced Mechanical Surface Testing, in: Anton Paar GmbH (Ed.), Application Report, Graz, 2017.
16. Nanoindentation identifications of mechanical properties of Cu6Sn5, Cu3Sn, and Ni3Sn4 intermetallic compounds derived by diffusion couples10.1016/j.msea.2007.07.093 ↗
17. Elastic analysis of some punch problems for a layered medium10.1016/0020-7683(87)90116-8 ↗
18. The equivalence of axisymmetric indentation model for three-dimensional indentation hardness10.1557/jmr.2009.0095 ↗
19. Roughness improvement and hardness enhancement in nanoscale Al/AlN multilayered thin films10.1063/1.119752 ↗
20. Nanoindentation characterization of intermetallic compounds formed between Sn–Cu (–Ni) ball grid arrays and Cu substrates10.1016/j.mseb.2009.06.013 ↗
21. The elastic properties of metallic alloys
22. Young's modulus of (Cu, Ag)–Sn intermetallics measured by nanoindentation10.1016/j.msea.2003.08.032 ↗
23. Y. Rémond, H. Garmestani, M. Baniassadi, S. Ahzi, Applied RVE reconstruction and homogenization of heterogeneous materials, iSTE, London, UK, Hoboken, NJ, USA, 2016.10.1002/9781119307563 ↗
24. Determination of plastic properties of metals by instrumented indentation using different sharp indenters10.1016/S1359-6454(02)00568-2 ↗