journal article·2010-08

Near-net-shape 95W–3.5Ni–1.5Fe thin-walled products produced by plasma spray forming

Y.M. Wang, X. Xiong, X.B. Min, L. Xie, F. Zheng

Materials Science and Engineering: A· Volume 527· Issue 21-22
Publisher page

Abstract

Abstract Tungsten heavy alloy 95W–3.5Ni–1.5Fe (in wt.%) refractory metallic thin-walled products (diameter ≤100 mm, length ≤150 mm and wall thickness ≤5 mm) were produced using plasma spray forming (PSF) covered in argon atmosphere at a pressure of 1.01 × 10 5 Pa followed by vacuum liquid phase sintering at 1465, 1485 and 1500 °C for 90 min, respectively. A lamellar structure consisting of vertical columnar grains and some fine particles was found in PSF deposits. Relative density of the deposits was about 87.70% with poor mechanical property. Upon vacuum liquid phase sintering, their density and property have been improved significantly. The microstructures of PSF deposits before and after vacuum sintering were found to consist with tungsten and (Ni, Fe)-rich phase. Volume fraction of (Ni, Fe)-rich phase was decreased due to vaporization that occurred in plasma spraying and vacuum liquid phase sintering. Their fracture surfaces were dominated by intergranular rupture. The lamellar structure remained in the deposits during early stages of sintering (solid state sintering and initial of liquid phase sintering). Particle rearrangement and rapid densification of the deposits did not occur until the surface of tungsten particles being modified and changed into spheroids by solution and precipitation. In the end, the PSF deposits have been transformed from lamellar structure into two phase composites with dispersed spheroidal tungsten grains embedded in a continuous network of (Ni, Fe)-rich phase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Fusion materials and technologies · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. German · Metall. Trans. A · 1984 · 15 · 74710.1007/BF02644206 ↗
2. Ariel · Powder Metall. Int. · 1973 · 5 · 126
3. German · 1996
4. Kang · Scripta Mater. · 2004 · 51 · 105110.1016/j.scriptamat.2004.08.008 ↗
5. V.M. Hovis, Kingston, Jr., W.G. Northcutt, O. Ridge, Jr., US Patent 4,332,617, June (1982).
6. Maneshian · J. Alloys Compd. · 2008 · 463 · 15310.1016/j.jallcom.2007.08.080 ↗
7. Mutasim · 1991 · 69
8. Samir · J. Eur. Ceram. Soc. · 2001 · 21 · 108710.1016/S0955-2219(00)00305-8 ↗
9. Owen · Int. J. Pharm. · 1997 · 159 · 6710.1016/S0378-5173(97)00272-X ↗
10. Pawlowsky · 1995
11. Jang · J. Alloys Compd. · 2007 · 434–435 · 36710.1016/j.jallcom.2006.08.215 ↗
12. Shunk · 1969
13. Elliott · 1965
14. Koch · Mater. Sci. Eng. A · 1998 · 244A · 3910.1016/S0921-5093(97)00824-1 ↗
15. Zhang · Rare Met. Mater. Eng. · 2005 · 34 · 1139
16. Vardelle · J. Therm. Spray Technol. · 1994 · 4 · 5010.1007/BF02648528 ↗
17. Vardelle · J. Therm. Spray Technol. · 2002 · 11 · 24410.1361/105996302770348907 ↗
18. Bose · Metall. Trans. A · 1988 · 19A · 246710.1007/BF02645474 ↗
19. C. Chausee, F. Nardou, PM’94, pp. 1545–1548.
20. Kingery · J. Appl. Phys. · 1959 · 30 · 30110.1063/1.1735155 ↗
21. Kingery · J. Appl. Phys. · 1959 · 30 · 30710.1063/1.1735156 ↗
22. Huppmann · Acta Metall. · 1960 · 30 · 307
23. Fan · Trans. Nonferrous Met. Soc. China · 1998 · 8 · 36
24. Toshihito · Int. J. Refract. Met. Hard Mater. · 1990 · 3 · 40
25. O’Donnell · J. Mater. Sci. · 1992 · 27 · 649010.1007/BF00576302 ↗
26. Li · Metall. Trans. A · 1984 · 20 · 149
27. Houben · 1983 · 66
28. Montanari · Mater. Lett. · 2002 · 52 · 10010.1016/S0167-577X(01)00375-5 ↗
29. Bemdt · 1980 · 310
30. McPherson · Thin Solid Films · 1982 · 97 · 20110.1016/0040-6090(82)90453-9 ↗
31. Zhang · Mater Heat Treat. · 1999 · 2 · 45