Fatigue crack growth behavior of a type of novel advanced high-strength steel in a FeCrNiBSi alloy system: A comparison between heat-treated cast and hot-rolled specimens
Source abstract
Abstract
Abstract The fatigue crack growth (FCG) behavior of a type of novel advanced high-strength steel in a FeCrNiBSi alloy system was investigated at room temperature. Two heat-treated cast and hot-rolled specimens were used to compare their FCG rate results obtained at a load ratio of 0.2 and at a frequency of 5 Hz. FCG paths and fracture surfaces of the specimens in the Paris regime, as well as unstable fracture surfaces, were observed by field emission gun scanning electron microscopy. The results showed that besides the dimension of matrix grains (austenite), the volume fraction, dimension, and morphology of second hard phases (boride phases) were also main factors in retarding crack propagation in the Paris regime. Fatigue striations and tearing ridges were observed in the fracture surfaces of both heat-treated cast and hot-rolled specimens, while quasi-cleavage facets and secondary cracks were only observed in the heat-treated cast and hot-rolled specimens, respectively. Roughness-induced, crack branching, and plasticity-induced crack closure mechanisms were more effective in retarding crack propagation in the heat-treated hot-rolled specimen than in the heat-treat cast specimen.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Demeri · 2013
2. Fatigue crack growth behavior of 316LN stainless steel with different nitrogen contents10.1016/j.proeng.2013.03.320 ↗
3. Microstructural effects on fatigue crack growth behavior of a microalloyed steel10.1016/j.proeng.2010.03.206 ↗
4. Effects of microstructure on fatigue crack growth behavior in cold-rolled dual phase steels10.1016/j.msea.2014.06.002 ↗
5. Fatigue crack growth behavior in ferritic–pearlitic steels with networked and distributed pearlite structures10.1016/j.ijfatigue.2006.09.008 ↗
6. Microstructural effects on fatigue crack growth in a low carbon steel10.1007/BF02697075 ↗
7. Fatigue crack growth behaviors in hot-rolled low carbon steels: a comparison between ferrite–pearlite and ferrite–bainite microstructures10.1016/j.msea.2012.09.036 ↗
8. Fatigue crack growth behavior of a coarse- and a fine- grained high manganese austenitic twin-induced plasticity steel10.1016/j.msea.2014.03.035 ↗
9. A study on fatigue crack growth in dual phase martensitic steel in air environment10.1007/BF02719909 ↗
10. Beraha · 1977
11. Fatigue crack closure under cyclic tension
12. Microstructural evolution and mechanical properties of a novel FeCrNiBSi advanced high-strength steel: Slow, accelerated and fast casting cooling rates10.1016/j.msea.2016.05.002 ↗
13. The effect of carbon content on fatigue strength of dual-phase steels10.1016/j.matdes.2006.04.016 ↗
14. Effect of liquid metal embrittlement on low cycle fatigue properties and fatigue crack propagation behavior of a modified 9Cr–1Mo ferritic–martensitic steel in an oxygen-controlled lead–bismuth eutectic environment at 350°C10.1016/j.msea.2014.09.003 ↗
15. Suresh · 1998
16. Influence of Al on the fatigue crack growth behavior of Fe–22Mn–(3Al)–0.6C TWIP steels10.1016/j.msea.2015.08.017 ↗
17. Fatigue crack growth of a metastable austenitic stainless steel10.1016/j.ijfatigue.2015.06.029 ↗
18. Fatigue crack growth rate of two pearlitic rail steels10.1016/j.engfracmech.2015.03.023 ↗
19. Effects of pearlite morphology and specimen thickness on fatigue crack growth resistance in ferritic–pearlitic steels10.1016/j.msea.2006.05.015 ↗
20. Alloying and aging effects on the fatigue crack growth of duplex stainless steels10.1016/S0921-5093(98)00587-5 ↗
21. Influence of ferrite fraction within martensite matrix on fatigue crack propagation: an experimental verification with dual phase steel10.1016/j.msea.2012.05.085 ↗