journal article·2019-05Open access

Effects of alloying and processing modifications on precipitation behavior and elevated temperature strength in 9% Cr ferritic/martensitic steels

Kristin Tippey, Paul Jablonski, Ömer Doğan, Jonathan Almer, Robert Hackenberg, John Speer, Aaron Stebner, Kester Clarke, Amy Clarke, Kip Findley

Abstract

Abstract Two low-carbon 9-Cr ferritic-martensitic steels were designed with the aim of decreasing M23C6 and maintaining or increasing MX phase fraction. A low-carbon (LC) alloy and a low-carbon, zero-niobium (0Nb) alloy were fabricated, their designs based upon the P92 alloy system. Solutionizing temperatures to maximize V and Nb in solution while avoiding δ-ferrite were determined to be 1170 °C for the P92 alloy and 1050 °C for LC and 0Nb, significantly lower than predicted using ThermoCalc® modeling. As was intended, the M23C6 phase fraction was reduced for LC and 0Nb alloys after both heat treating and aging relative to the base P92 alloy, as determined by wide angle x-ray scattering (WAXS) analysis. Dislocation density measurements from x-ray line broadening in P92 and LC suggest these alloys had more stable dislocation substructures than 0Nb at lower temperature and shorter time aging conditions. While LC exhibited lower microhardness than P92 at room temperature, the tensile properties were comparable at 650 °C, suggesting that elevated temperature strength can be achieved with lower carbon contents. Aging studies showed that P92 had a more stable microstructure for higher temperature and longer time aging conditions. The P92 alloy also had a longer stress rupture life, implying that the M23C6 precipitate contribution to thermal stability is important. Evidence of Z-phase was discovered for the LC alloy aged 10,000 h at 650 °C, corresponding to decreased strength and increased ductility. Overall, the stress rupture lives of the modified heat-treatment variations of P92 and LC compare favorably to literature values for 9% Cr steels with conventional heat treatments.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Fusion materials and technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. 2014
2. Literature review: precipitation in creep resistant austenitic stainless steels10.1179/026708301101508972 ↗
3. Coarsening of precipitates and degradation of creep resistance in tempered martensite steels10.1016/j.msea.2008.04.088 ↗
4. Hardness variation in P92 heat-resistant steel based on microstructural evolution during creep10.1002/srin.201200265 ↗
5. Creep-strengthening of steel at high temperatures using nano-sized carbonitride dispersions10.1038/nature01740 ↗
6. Effect of carbon concentration on precipitation behavior of M23C6 carbides and MX carbonitrides in martensitic 9Cr steel during heat treatment10.1007/s11661-004-0299-x ↗
7. Concepts for the development of nanoscale stable precipitation-strengthened steels manufactured by conventional methods
8. Tippey · 2017
9. Standard specification for seamless ferritic alloy-steel pipe for high-temperature service
10. Development of high-strength, elevated-temperature, corrosion-resistant steel
11. Cipolla · 2010
12. The effect of delta-ferrite in P92 steel on the formation of Laves phase and cavities for the reduction of low cycle fatigue and creep-fatigue life10.4028/www.scientific.net/KEM.297-300.463 ↗
13. P. Jablonski and J. Hawk, Nitrogen Control in VIM Melts, in: Proceedings of the 2013 International Symposium on Liquid Metal Processing & Casting, 2013, pp. 315–319.10.1002/9781118830857.ch45 ↗
14. Homogenizing advanced alloys: thermodynamic and kinetic simulations followed by experimental results10.1007/s11665-016-2451-3 ↗
15. GSAS-II: the genesis of a modern open-source all purpose crystallography software package10.1107/S0021889813003531 ↗
16. K. Matsui, A. Ogawa, J. Kikuma, M. Tsunashima, T. Ishikawa, and S. Matsuno, Strain Broadening Caused by Dislocations, in: Proceedings of the Denver X-ray Conference on Applications of X-ray Analysis, 2009, vol. 16, no. 1, pp. 1–7.
17. Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
18. Standard test methods for tension testing of metallic materials
19. Prior austenite grain size and tempering effects on the dislocation density of low-C Nb–Ti microalloyed lath martensite10.1016/j.scriptamat.2015.05.036 ↗
20. New nanoparticle-strengthened ferritic/martensitic steels by conventional thermo-mechanical treatment
21. Effect of precipitates on long-term creep deformation properties of P92 and P122 type advanced ferritic steels for USC power plants10.1016/j.msea.2008.05.055 ↗
22. Effect of thermo-mechanical treatment on microstructure and mechanical properties of P92 heat resistant steel10.1016/j.msea.2012.09.040 ↗
23. Hardness variation in P92 heat-resistant steel based on microstructural evolution during creep10.1002/srin.201200265 ↗
24. Stabilization of martensitic microstructure in advanced 9Cr steel during creep at high temperature10.1016/j.msea.2003.11.073 ↗