journal article·2018-08

Deformation characteristic of a Ti-based bulk metallic glass composite with fine microstructure

S. Yang, X.C. Li, R. Wei, M. Meng, L. He, S.F. Zhang

Publisher page

Abstract

Abstract A bulk metallic glass composite (BMGC) with a composition of Ti65.6Cu13.2Pd5.6Sn3.6Nb12 was prepared via suction casting. Microstructure mainly consisting of fine β-Ti dendrites sized about 5 µm and nano-scale interdendritic glassy matrix was obtained in the BMGC. The mechanical behavior was compared with that of the same alloy in a polycrystalline state under compressive and bending conditions. It was found that the nano-scale glassy matrix with limited volume fraction remarkably increased the yield strength of the BMGC, furthermore, plastic deformability of the corresponding polycrystalline alloy could be preserve by the BMGC. Upon loading, the nano-scale glassy matrix could exert a strong restriction effect on the slip deformation inside the micron-scale dendritic crystals; no obvious shear-banding was exhibited in the glassy matrix during the deformation. This deformation characteristic might be attributed to the possible homogeneous deformation mode of the glassy matrix at the nano-scale.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallic Glasses and Amorphous Alloys · Phase-change materials and chalcogenides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Bioactive titanate nanomesh layer on the Ti-based bulk metallic glass by hydrothermal–electrochemical technique10.1016/j.actbio.2008.10.014 ↗
2. Designing biocompatible Ti-based metallic glasses for implant applications10.1016/j.msec.2012.11.015 ↗
3. Biocompatibility study on Ni-free Ti-based and Zr-based bulk metallic glasses10.1016/j.msec.2017.02.006 ↗
4. Improved plasticity and corrosion behavior in Ti–Zr–Cu–Pd metallic glass with minor additions of Nb: an alloy composition intended for biomedical applications10.1016/j.msea.2012.08.058 ↗
5. Development of tough, low-density titanium-based bulk metallic glass matrix composites with tensile ductility10.1073/pnas.0809000106 ↗
6. In situ high-energy X-ray diffraction studies of deformation-induced phase transformation in Ti-based amorphous alloy composites containing ductile dendrites10.1016/j.actamat.2013.04.045 ↗
7. Tensile deformation micromechanisms for bulk metallic glass matrix composites: from work-hardening to softening10.1016/j.actamat.2011.03.036 ↗
8. Microstructure and tensile properties of high-strength high-ductility Ti-based amorphous matrix composites containing ductile dendrites10.1016/j.actamat.2011.08.006 ↗
9. Tensile deformation behavior of two Ti-based amorphous matrix composites containing ductile β dendrites10.1016/j.msea.2012.05.061 ↗
10. Deformation behavior of a Ti-based bulk metallic glass composite with excellent cryogenic mechanical properties10.1016/j.matdes.2013.07.076 ↗
11. Designing metallic glass matrix composites with high toughness and tensile ductility10.1038/nature06598 ↗
12. On the microstructure–tensile property correlations in bulk metallic glass matrix composites with crystalline dendrites10.1016/j.actamat.2012.06.032 ↗
13. Large-sized Zr-based bulk-metallic-glass composite with enhanced tensile properties10.1016/j.intermet.2012.03.054 ↗
14. Mechanical behavior and wear performance of a Ti-based bulk metallic glass composite containing dendritic and intermetallic phases10.1016/j.msea.2016.07.004 ↗
15. Composition dependence of the microstructure and mechanical behavior of Ti–Zr–Cu–Pd–Sn–Nb bulk metallic glass composites10.1016/j.intermet.2017.06.006 ↗
16. Fabrication of Ni-free Ti-based bulk-metallic glassy alloy having potential for application as biomaterial, and investigation of its mechanical properties, corrosion, and crystallization behavior10.1557/jmr.2007.0154 ↗
17. A new Ti-based bulk glassy alloy with potential for biomedical application10.1016/j.msea.2007.01.044 ↗
18. Glass-forming ability and mechanical properties of Ti-based bulk glassy alloys with large diameters of up to 1 cm10.1016/j.intermet.2008.05.006 ↗
19. Effects of Sn addition on mechanical properties of Ti-based bulk metallic glass composites10.1016/j.matdes.2016.08.051 ↗
20. A strategy for designing bulk metallic glass composites with excellent work-hardening and large tensile ductility10.1016/j.jallcom.2016.05.290 ↗
21. Formation of CuZr-based bulk metallic glass composites containing nanometer-scale B2-CuZr phase through sub-Tg annealing10.1016/j.jallcom.2014.08.045 ↗
22. New correction terms concerning three-point and four-point bending tests10.1016/j.polymertesting.2016.07.025 ↗
23. Solution to the problem of the poor cyclic fatigue resistance of bulk metallic glasses10.1073/pnas.0900740106 ↗
24. Microstructure controlled shear band pattern formation and enhanced plasticity of bulk metallic glasses containing in situ formed ductile phase dendrite dispersions10.1103/PhysRevLett.84.2901 ↗
25. Mechanical properties of Zr56.2Ti13.8Nb5.0Cu6.9Ni5.6Be12.5 ductile phase reinforced bulk metallic glass composite10.1016/S1359-6454(01)00068-4 ↗
26. Realization of high tensile ductility in a bulk metallic glass composite by the utilization of deformation-induced martensitic transformation10.1016/j.scriptamat.2011.04.037 ↗
27. Modeling deformation behavior of Cu–Zr–Al bulk metallic glass matrix composites10.1063/1.3222973 ↗
28. Microstructural heterogeneities governing the deformation of Cu47.5Zr47.5Al5 bulk metallic glass composites10.1016/j.actamat.2009.07.042 ↗
29. Significant tensile ductility and toughness in an ultrafine-structured Ti68.8Nb13.6Co6Cu5.1Al6.5 bi-modal alloy10.1016/j.msea.2014.07.108 ↗
30. High strength beta titanium alloys: new design approach10.1016/j.msea.2015.01.073 ↗
31. Size-independent strength and deformation mode in compression of a Pd-based metallic glass10.1016/j.actamat.2008.06.028 ↗
32. Compression testing of metallic glass at small length scales-Effects on deformation mode and stability10.1016/j.actamat.2010.06.054 ↗
33. Approaching the ideal elastic limit of metallic glasses10.1038/ncomms1619 ↗
34. Intrinsic and extrinsic size effects in the deformation of metallic glass nanopillars10.1016/j.actamat.2011.11.023 ↗
35. Transition from a strong-yet-brittle to a stronger-and-ductile state by size reduction of metallic glasses10.1038/nmat2622 ↗
36. Ductile necking behavior of nanoscale metallic glasses under uniaxial tension at room temperature10.1016/j.actamat.2013.05.001 ↗
37. Ductility and work hardening in nano-sized metallic glasses10.1063/1.4907773 ↗
38. Uniform tensile elongation in framed submicron metallic glass specimen in the limit of suppressed shear banding10.1016/j.actamat.2011.05.035 ↗
39. New compositional design for creating tough metallic glass composites with excellent work hardening10.1016/j.actamat.2014.11.055 ↗