journal article·2002-07

Localized corrosion behavior of Al3Ti–Cr alloys in 3.5 wt.% NaCl solution

Yong-Jae Yu, Jung-Gu Kim

Materials Science and Engineering: A· Volume 332· Issue 1-2
Publisher page

Abstract

Abstract Al 3 Ti alloys have received a lot of attention as potential light materials because of their low density and high strength at elevated temperatures. The induction melting method followed by thermomechanical treatment was used for preparation of L1 2 -typed Al 3 Ti–Cr alloys, i.e. Al 67 Ti 25 Cr 8 , Al 66 Ti 24 Cr 10 and Al 59 Ti 26 Cr 15 . The corrosion behavior of Al 3 Ti–Cr alloys in deaerated 3.5 wt.% NaCl solution was investigated by electrochemical corrosion tests and surface analysis. Particular attention was paid to the effects of Cr addition on the surface film composition and its breakdown related to the corrosion behavior. The result of cyclic potentiodynamic polarization test showed that E pit and E prot increased with increasing Cr content. This indicates that Al 3 Ti–Cr alloys with higher Cr content are effective in improving relative resistance to pit initiation and propagation. In electrochemical impedance spectroscopy, an increase of Cr content increased polarization resistance ( R p ) and decreased the depressed angle, which is strongly related to pitting resistance. Auger electron spectroscopy analyses were performed in order to characterize in-depth distribution of constituents in the passive film. Cr was detected earlier from the outer surface with increasing Cr content. Energy dispersive X-ray spectroscopy techniques were used to examine the effect of alloying elements inside pit. The amount of Ti inside pit was enriched as increasing Cr content.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. Chen · Scr. Metall. Mater. · 1992 · 27 · 45510.1016/0956-716X(92)90210-6 ↗
2. Mabuchi · Mater. Trans. JIM · 1997 · 38 · 56010.2320/matertrans1989.38.560 ↗
3. Lee · Mater. Sci. Eng. · 2000 · A290 · 110.1016/S0921-5107(99)00524-3 ↗
4. Kogachi · Intermetallics · 1995 · 3 · 32710.1016/0966-9795(95)97293-A ↗
5. Mabuchi · Intermetallics · 1996 · 4 · 19310.1016/0966-9795(96)00005-2 ↗
6. Parfitt · Scr. Metall. Mater. · 1991 · 25 · 72710.1016/0956-716X(91)90123-I ↗
7. Mabuchi · Scr. Metall. Mater. · 1990 · 24 · 50510.1016/0956-716X(90)90191-I ↗
8. Kim · Scr. Mater. · 2000 · 43 · 57910.1016/S1359-6462(00)00485-1 ↗
9. ASTM G 61, Annual Book of ASTM Standards, ASTM, PA, 1995.
10. Frankel · J. Electrochem. Soc. · 1989 · 136 · 124310.1149/1.2096864 ↗
11. Akiyama · Mater. Sci. Eng. · 1997 · A226-228 · 92010.1016/S0921-5093(96)10819-4 ↗
12. EG&G Princeton Applied Research. Impedance Measurement, Application Note. EG&G Princeton Applied Research, Princeton, NJ, 1989, p. 1.
13. Cottis · 1999 · 36
14. J.R. Scully, D.C. Silverman, M.W. Kendig. Electrochemical Impedance — Analysis and Interpretation, ASTM STP 1188, Philadelphia, PA, ASTM, 1993, p. 54.10.1520/STP1188-EB ↗
15. Roberge · J. Appl. Electrochem. · 1990 · 20 · 100410.1007/BF01019580 ↗
16. Roberge · Corrosion · 1992 · 48 · 44710.5006/1.3315959 ↗