journal article·2010-08

Indentation of power law creep solids by self-similar indenters

Wei-Min Chen, Yang-Tse Cheng, Min Li

Materials Science and Engineering: A· Volume 527· Issue 21-22
Publisher page

Abstract

For creep solids obeying the power law under tension proposed by Tabor, namely sigma = b(epsilon) over dot(m), it has been established through dimensional analysis that for self-similar indenters the load F versus indentation depth h can be expressed as F(t) = bh(2)(t)[(h) over dot(t)/h(t)](m)Pi(alpha) where the dimensionless factor Pi(alpha) depends on material parameters such as m and the indenter geometry. In this article, we show that by generalizing the Tabor power law to the general three dimensional case on the basis of isotropy, this factor can be calculated so that indentation test can be used to determine the material parameters b and m appearing in the original power law. Hence indentation test can replace tension test. This could be a distinct advantage for materials that come in the form of thin films, coatings or otherwise available only in small amounts. To facilitate application values of this constant are given in tabulated form for a range of material parameters. (C) 2010 Elsevier B.V. All rights reserved.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Force Microscopy Techniques and Applications · Tribology and Wear Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Lee · Q. Appl. Math. · 1955 · 13 · 18310.1090/qam/69741 ↗
2. Radok · Q. Appl. Math. · 1957 · 15 · 19810.1090/qam/92453 ↗
3. Lee · J. Appl. Mech. · 1960 · 27 · 43810.1115/1.3644020 ↗
4. Hunter · J. Mech. Phys. Solids · 1960 · 8 · 21910.1016/0022-5096(60)90028-4 ↗
5. Graham · Int. J. Eng. Sci. · 1965 · 3 · 2710.1016/0020-7225(65)90018-2 ↗
6. Graham · Int. J. Eng. Sci. · 1967 · 5 · 49510.1016/0020-7225(67)90037-7 ↗
7. Yang · J. Appl. Mech. · 1966 · 33 · 39510.1115/1.3625055 ↗
8. Ting · J. Appl. Mech. · 1966 · 33 · 84510.1115/1.3625192 ↗
9. Ting · J. Appl. Mech. · 1968 · 35 · 24810.1115/1.3601188 ↗
10. Cheng · J. Polym. Sci.: Part B: Polym. Phys. · 2001 · 38 · 1010.1002/(SICI)1099-0488(20000101)38:1<10::AID-POLB2>3.0.CO;2-6 ↗
11. Larrson · Polym. Test · 1998 · 17 · 4910.1016/S0142-9418(97)00038-X ↗
12. Shimizu · J. Mater. Res. · 1999 · 14 · 407510.1557/JMR.1999.0550 ↗
13. Sakai · Non-Cryst. Solids · 2001 · 282 · 23610.1016/S0022-3093(01)00316-7 ↗
14. Sakai · Philos. Mag. A · 2002 · 82 · 184110.1080/01418610208235695 ↗
15. Oyen · J. Mater. Res. · 2003 · 18 · 13910.1557/JMR.2003.0020 ↗
16. Cheng · Struct. Control Health Monitor. · 2006 · 13 · 56110.1002/stc.127 ↗
17. Cheng · Mater. Sci. Eng. A · 2005 · 409 · 9310.1016/j.msea.2005.05.118 ↗
18. Cheng · J. Mater. Res. · 2005 · 20 · 104610.1557/JMR.2005.0141 ↗
19. Mulhearn · J. Inst. Met. · 1960 · 89 · 7
20. Bower · Proc. R. Soc. Lond. Ser. A · 1993 · 441 · 9710.1098/rspa.1993.0050 ↗
21. Cheng · Philos. Mag. Lett. · 2001 · 81 · 910.1080/09500830010008457 ↗
22. Li · J. Mater. Res. · 2004 · 19 · 7310.1557/jmr.2004.19.1.73 ↗