Predicting microstructure and strength for AISI 304L stainless steel forgings
Source abstract
Abstract
Abstract Specially designed billets of AISI 304L stainless steel were forged at two temperatures, 843 °C and 941 °C, and with varying transfer times. The machined 304L billets were thick near the center (51 mm) and thin near the periphery (10 mm) such that forging with a flat platen resulted in regions of high strain (center) and low strain (periphery). Multiple metallographic samples were extracted from one experimental forging for each temperature (water quenched forging with nominal transfer times). Microstructural analysis revealed that recrystallization initiated at about 1.4 plastic strain for forgings made at 843 °C and 1.1 plastic strain for 941 °C. Mechanical tests—performed using tensile bars from multiple locations from each forging—revealed that the resulting yield strength increased with strain up ~10–20% recrystallization, then decreased. Coupled thermo-mechanical simulations estimated a temperature increase of up to 162 °C in the center of the forging due to rapid deformation in the High Energy Rate Forging (HERF) press. Simulation using updated BCJ model parameters for 304L stainless steel predicted the strain distributions using the scalar value, equivalent plastic strain. The predicted trends for percent recrystallization and yield strength from this simulation (using the internal state variable BCJ model) agreed qualitatively with experimental tensile test results, but the quantitative comparison leaves room for improvement. Both the simulation and the experimental results clarify that the microstructure and strength of 304L forgings are difficult to control in a forging with excessive strain variation. It is recommended that strain variation be minimized and overall strain be kept under ~0.5 to best control the strength and grain structure of 304L stainless steel. Excessive transfer time appeared to have little effect on the forging yield strength, but air cooling and die cooling after forging indicated softening for the forgings made at 941 °C.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. Computer Simulation to Predict Load, Stress, and Metal Flow in an Axisymmetric Closed-Die Forging
2. Investigation of metal flow and preform optimization in flashless forging of a connecting rod10.1016/0924-0136(96)02290-X ↗
3. Determination of flow stress for sheet metal forming using the viscous pressure bulge (VPB) test10.1016/S0924-0136(03)00838-0 ↗
4. Effect of hot working on structure and strength of Type 304L austenitic stainless steel10.1007/BF02647245 ↗
5. Finite element simulation of carbide precipitation in austenitic stainless steel 304
6. Quantitative measurement of deformation-induced martensite in 304 stainless steel by X-ray diffraction10.1016/j.scriptamat.2004.03.011 ↗
7. V. Marlow, J. Astorian, M. Mataya, HERF Die Design and Metallurgy Handbook, Golden, CO, 1988.
8. Determination of the heat transfer coefficient at the workpiece-die interface for the forging process10.1243/095440502760272449 ↗
9. A state variable damage model for temperature and strain rate dependent materials
10. Effect of internal heating during hot compression10.1007/BF02649226 ↗
11. Experimental study of internal variable evolution in SS304L at multiple rates and temperatures10.1115/1.2812362 ↗
12. M. Chiesa et al., Prediction of final material state in multi-stage forging processes, in: Proceedings of the Nonuniform 2004, 8th International Conference on Numerical Methods in Industrial Forming Processes, 2004, pp. 510–515.10.1063/1.1766576 ↗
13. Validation of a model for static and dynamic recrystallization in metals
14. Effect of forging strain rate and deformation temperature on the mechanical properties of warm-worked 304L stainless steel10.1016/j.jmatprotec.2010.01.014 ↗
15. Sierra (engineering mechanics simulation code suite). (Online). Available: 〈https://sierradist.sandia.gov/〉.
16. Hot deformation behavior and microstructural evolution of a superaustenitic stainless steel10.1016/j.msea.2009.10.051 ↗
17. Flow stress and microstructural evolution during hot working of alloy 22Cr-13Ni-5Mn-0.3N austenitic stainless steel10.1007/BF02649862 ↗
18. A.A. Brown et al., Validation of thermal-mechanical modeling of stainless steel forgings, in: Proceedings of the XI Int. Conf. Comput. Plast. Fundam. Appl., 2011.
19. Recrystallization in AISI 304 austenitic stainless steel during and after hot deformation10.1016/j.msea.2007.08.026 ↗