A comparison between hot-rolling process and twin-screw rheo-extrusion process for fabrication of aluminum matrix nanocomposite
Source abstract
Abstract
Abstract Solid-state modification of SiC nanoparticles in a ball-mill is a known method for deagglomeration of as-received nanoparticles in a bed of metallic carriers that will also aid their better injection and releasing into the melt. The melt temperature and condition of the melt is very important for a better interaction of composite powders including ceramic nanoparticles and metallic carrier with the melt. In this study, aluminum A356 matrix nanocomposites were produced by liquid-state stir casting at 715 °C followed by twin-screw rheo-extrusion (TSRE) in the semi-solid state to enhance the produced composite properties. For this purpose, SiC nanocomposite superstructures were prepared using ball-milling of SiC nanopowders with micron-sized titanium and nickel (separately) as carrier agents. Also, hot-rolling (HR) process was applied on liquid-state stir cast nanocomposites to compare the mechanical properties of rolled sheets with TSRE-processed bars. The experimental results indicated that stir-cast samples before TSRE and HR consisted various types of defects with poor dispersion of nanoparticles in some areas. However, more improved dispersions for the nanoparticles were obtained after TSRE and HR and rolled sheets had considerable improved mechanical properties compared with TSRE bars. This latter improvement was determined to be mainly due to extensive fragmentation and dispersion of eutectic silicon, Ti-rich, and Ni-rich intermetallic phases.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Bauxite Residue and Utilization · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Effects of T6 heat treatment on the microstructure, tensile properties, and fracture behavior of the modified A356 alloys10.1016/j.matdes.2011.11.018 ↗
2. Comparison of the semi-solid constitutive behaviour of A356 and B206 aluminum foundry alloys10.1016/j.jmatprotec.2018.10.029 ↗
3. Bonding interfacial characterization of SiCp/8009Al composite and A356 aluminum alloy using compound casting10.1016/j.jmatprotec.2018.08.007 ↗
4. Development of high strength and toughness nano-SiCp/A356 composites with ultrasonic vibration and squeeze casting10.1016/j.jmatprotec.2019.01.021 ↗
5. Study on the incorporation of ceramic nanoparticles into the semi-solid A356 melt10.1016/j.matchemphys.2019.03.048 ↗
6. Al alloy metal matrix composites reinforced by WS2 inorganic nanomaterials10.1016/j.msea.2017.10.041 ↗
7. Fracture mechanism of nano- and submicron-SiCp/Mg composite during room temperature tensile test: interaction between double sized particles and dislocations10.1016/j.jallcom.2019.03.329 ↗
8. Effects of mechanical stirring and short heat treatment on thixoformed of carbon nanotube aluminium alloy composite10.1016/j.jallcom.2019.02.217 ↗
9. Wear properties of A356/Al 2 O 3 metal matrix composites produced by semisolid processing10.1016/j.proeng.2013.12.166 ↗
10. Fabrication of A356 composite reinforced with micro and nano Al 2 O 3 particles by a developed compocasting method and study of its properties10.1016/j.jallcom.2011.08.105 ↗
11. A novel graphene-stimulated semi-solid processing to fabricate advanced aluminium matrix nanocomposites10.1016/j.msea.2018.09.001 ↗
12. Effects of Mg content on microstructure and mechanical properties of SiCp/Al-Mg composites fabricated by semi-solid stirring technique10.1016/S1003-6326(09)60385-X ↗
13. Effects of nanosized TiCp on the microstructure evolution and tensile properties of an Al-Mg-Si alloy during cold rolling10.1016/j.msea.2018.11.078 ↗
14. Enhanced strength and ductility of A356 alloy due to composite effect of near-rapid solidification and thermo-mechanical treatment10.1016/j.msea.2019.03.039 ↗
15. Thixoforming of a high performance HP9/4/30 steel10.1016/j.msea.2004.12.013 ↗
16. Thermodynamic simulation on thixoformability of aluminium alloys for semisolid metal processing
17. A novel (AlN+ Si3N4)/Al composite with well-balanced strength and ductility10.1016/j.msea.2018.04.053 ↗
18. Effect of solid fraction on microstructures and mechanical properties of a Mg-Al-La-Ca alloy processed by rheocasting10.1016/j.jallcom.2018.10.292 ↗
19. Effects of casting temperature on the microstructure and wear resistance of compocast A356/SiCp composites: a comparison between SS and SL routes10.1016/j.jmatprotec.2004.04.328 ↗
20. Nano-sized aluminum oxide reinforced commercial casting A356 alloy matrix: evaluation of hardness, wear resistance and compressive strength focusing on particle distribution in aluminum matrix10.1016/j.compositesb.2013.04.038 ↗
21. Manufacturing of cast A356 matrix composite reinforced with nano-to micrometer-sized SiC particles10.1007/s12598-015-0689-9 ↗
22. Fabrication of aluminum matrix composites reinforced with nano-to micrometer-sized SiC particles10.1016/j.matdes.2015.09.130 ↗
23. Influence of modification, solidification conditions and heat treatment on the microstructure and mechanical properties of A356 aluminum alloy10.1023/B:JMSC.0000017764.20609.0d ↗
24. Microstructure and mechanical properties of rheo-diecast (RDC) aluminium alloys10.1016/j.msea.2005.09.001 ↗
25. Processing of advanced Al/SiC particulate metal matrix composites under intensive shearing – a novel Rheo-process10.1016/j.compositesa.2008.10.017 ↗
26. Reinforcement coatings and interfaces in aluminium metal matrix composites10.1023/A:1004674822751 ↗
27. Microstructural characterization of ball-milled metal matrix nanocomposites (Cr, Ni, Ti)-25 wt%(Al2O3np, SiCnp)10.1080/02726351.2016.1211778 ↗
28. Fabrication of in-situ intermetallic compound dispersed aluminum matrix composites by addition of metal powders10.2320/matertrans.47.2972 ↗
29. The effect of Ni and V trace elements on the mechanical properties of A356 aluminium foundry alloy in as-cast and T6 heat treated conditions10.1016/j.msea.2014.05.059 ↗
30. Effects of the addition of Ti powders on the microstructure and mechanical properties of A356 alloy10.1016/j.powtec.2013.12.052 ↗