journal article·2017-05

Microstructural characteristics and mechanical heterogeneity of underwater wet friction taper plug welded joints for low-alloy pipeline steel

Junzhen Xiong, Xinqi Yang, Wei Lin, Kaixuan Liu

Publisher page

Abstract

Abstract Underwater wet friction taper plug welding experiments have been performed on X52 pipeline steel with 6500–7500 rpm rotational speeds at 30–45 kN axial forces, and the microstructural characteristics and mechanical heterogeneity of defect-free friction taper plug welded joints are discussed thoroughly. It is found that the microstructure of welded joint is remarkably inhomogeneous and very different from the base metal. The welded joint has dramatically coarse grains and is dominantly characterized by a mixture of quenched martensite, upper bainite and various types of ferrites including Widmanstatten ferrite. Unlike the traditional solid-state friction welding processes, the relative homogeneous microstructure with fine and equiaxed grains cannot be obtained in the friction taper plug welding process. The axial force has a greater impact on microstructure of welded joint as compared to rotational speed. The hardness profiles measured in cross-section of welded joints are severely non-uniform, ranging from 200 to 400 HV1, due to the inhomogeneity of microstructure. The impact absorbed energy of welded joint with V-notch in the bonding zone was considerably lower than that of base material (about only 20% of parent metal) because of the local obviously coarse grain, Widmanstatten ferrite and banding ferrite defect. The microstructural inhomogeneity results in mechanical heterogeneity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Microstructure and Mechanical Properties of Steels · Mechanical stress and fatigue analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Nixon · 2000
2. Underwater welding – a review
3. Underwater wet welding for HSLA steels: chemical composition, defects, microstructures, and mechanical properties10.1007/s40195-015-0300-2 ↗
4. S. Karthik Remote operated underwater welding vehicle, in: Proceedings of the 21st Offshore Symposium 2016: Emerging Offshore Technology and Deepwater Trends, February 16, 2016, Society of Naval Architects and Marine Engineers (SNAME) Texas Section, Houston, TX, United States, 2016.
5. A study on the arc characteristics of underwater wet welding process
6. Diffusible hydrogen in underwater wet welding
7. W.C.D.D. Silva et al., Effect of the hydrostatic pressure in the diffusible hydrogen at the underwater wet welding, in: Proceedings of the International Conference on Ocean, Offshore and Arctic Engineering, ASME 2012, 2012, pp. 1–8.10.1115/OMAE2012-83002 ↗
8. R.E. Andrews, J.S. Mitchell, Underwater repair by friction stitch welding. Metals and Materials Bury St Edmunds, 6(12), 1990, pp. 796–797.
9. Friction stitch welding – a new kind of material forming technology
10. D.E. Gibson et al., Engineering applications of friction stitch welding, in: Proceedings of the 20th International Conference on Offshore Mechanics and Arctic Engineering; Materials, June 3, 2001–June 8, 2001, American Society of Mechanical Engineers, Rio de Janeiro, Brazil, 2001.
11. Friction hydro pillar process as an alternative repair technology for creep evaluation sites on thick-walled 10CrMo910 creep-resistant steel structures
12. Process parameter influence on performance of friction taper stud welds in AISI 4140 steel10.1016/j.matdes.2011.02.001 ↗
13. Evaluation of discontinuities in A36 steel repairs with friction hydro pillar processing using different axial forces10.2355/isijinternational.53.2269 ↗
14. Study of microstructural evolution of friction taper plug welded joints of C-Mn steels10.1179/136217110X12720264008556 ↗
15. Fracture toughness of friction hydro-pillar processing welding in C–Mn steel10.1016/j.matdes.2011.07.056 ↗
16. Perrett · 2007
17. Welding process and microstructure of weld for friction hydro pillar welded DH36 high strength steel
18. Experimental study of friction taper plug welding for low alloy structure steel: welding process, defects, microstructures and mechanical properties10.1016/j.matdes.2014.05.026 ↗
19. Microstructure and mechanical properties of underwater friction taper plug weld on X65 steel with carbon and stainless steel plugs10.1179/1362171815Y.0000000089 ↗
20. API Specification 5L, Specification for Line Pipe, American Petroleum Institute, 45th ed., 2012.
21. Thermal and gas analyses of the reaction between iron carbide and steam with hydrogen generation at 573K10.1016/j.ijhydene.2003.08.006 ↗
22. M. Liang et al., Thermodynamics study on solid phase decarbonization of high carbon ferrommanganese powder, FERRO-ALLOYS, (1), 2009, pp. 14–17.