journal article·2008-12Open access

Creep behavior of a dispersion-strengthened Cu–Ti–Al alloy obtained by reaction milling

Rodrigo G. Espinoza, Rodrigo H. Palma, Aquiles O. Sepúlveda, Alejandro Zúñiga

Materials Science and Engineering: A· Volume 498· Issue 1-2

Abstract

Abstract Creep results of a dispersion-strengthened nominal-composition Cu-2.5 vol.%Ti-2.5 vol.%Al alloy, and the adjustment of those results to existing creep models, are presented. The alloy was prepared by reaction milling; its microstructural characterization by transmission electron microscopy had been recently reported elsewhere. Creep tests were here performed at 773, 973 and 1123 K, under loads that produced steady-state creep rates between 9 × 10 −7 and 2 × 10 −4 s −1 . Two deformation models, available in the literature, were considered: dislocation creep, where the strain rate is controlled by the dislocation-particle interaction within the grains, and diffusional creep, controlled by the interaction between grain-boundary dislocations and particles. In all creep experiments the alloy exhibited high values of the apparent stress exponent, as typical for dispersion-strengthened alloys. Through model adjustment, the operating creep mechanisms where determined: at 773 and 1123 K, creep is controlled by dislocation/particle interactions taking place in the matrix and in grain boundaries, respectively, while at the intermediate temperature of 973 K, controlling dislocation-particle interactions would occur both in the matrix and in grain boundaries.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Groza · Mater. Sci. Eng. · 1993 · A171 · 11510.1016/0921-5093(93)90398-X ↗
2. Anzel · Z. Metalkd. · 1999 · 90 · 621
3. Palma · J. Mater. Proc. Technol. · 2005 · 169-1 · 6210.1016/j.jmatprotec.2005.02.260 ↗
4. Lü · 1998
5. Sauer · Z. Metallkd. · 1998 · 89 · 119
6. R. Palma, A. Sepúlveda, A. Zúñiga, R. Pérez., Molienda reactiva de aleaciones Cu–Ti–C, Anales de las Jornadas SAM-CONAMET-AAS 2001, Posadas, Argentina, Septiembre (2001) 317–324.
7. Rösler · Acta Metall. Mater. · 1990 · 38 · 67110.1016/0956-7151(90)90223-4 ↗
8. Rösler · Metall. Trans. · 1992 · 23A · 1251
9. Espinoza · Mater. Sci. Eng. A · 2007 · 454–455 · 18310.1016/j.msea.2006.11.042 ↗
10. Broyles · Metall. Trans. A · 1996 · 27A · 121710.1007/BF02649859 ↗
11. Arzt · Acta Metall. · 1983 · 31 · 197710.1016/0001-6160(83)90015-9 ↗
12. Kudashov · Mater. Sci. Eng. A · 2004 · 387–389 · 63910.1016/j.msea.2004.01.118 ↗
13. Williams · 1996
14. Le Roy · Acta Metall. · 1981 · 29 · 150910.1016/0001-6160(81)90185-1 ↗
15. Taylor · J. Inst. Met. · 1938 · 62 · 307
16. Frost · 1982
17. Besterci · Scripta Met. et Mater. · 1994 · 30-9 · 114510.1016/0956-716X(94)90329-8 ↗
18. Lloyd · Mater. Sci. Eng. · 1980 · 46 · 110.1016/0025-5416(80)90186-X ↗
19. Anderson · Met. Mater. Trans. A · 2001 · 32 · 121110.1007/s11661-001-0130-x ↗
20. Nagorka · Metall. Mater. Trans. A · 1995 · 26 · 87310.1007/BF02649084 ↗
21. Ballufi · Phys. Status Solidi · 1970 · 42 · 1110.1002/pssb.19700420102 ↗
22. Beeré · Met. Sci. J · 1971 · 5 · 10710.1179/030634571790439757 ↗
23. Kuchařová · Mater. Sci. Eng. A · 2003 · 348 · 17010.1016/S0921-5093(02)00631-7 ↗