journal article·2004-04

Analysis of the creep behavior and microstructure of PWHT steam piping exposed to service

Alfonso R. Fernández Fuentes, Nelson G. Alcântara

Materials Science and Engineering: A· Volume 371· Issue 1-2
Publisher page

Abstract

Abstract A comparative study was made of the material of a steam piping system (1.25Cr0.5Mo steel operating at 480 °C for over 20 years) and the areas affected by post-weld heat treatment (PWHT) applied during a simulated weld repair of this component in terms of its creep and microstructural behavior. This study was based on the results of a qualitative microstructural characterization by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and on constant load creep rupture tests. The PWHT caused precipitation of rod-shaped Fe 2 MoC carbide in the ferrite matrix, which, during service, had already undergone precipitation and coarsening of the M 2 C carbide, coupled with impoverishment of the matrix’s alloying element. From the standpoint of the stress and temperature values close to those specified for 1.25Cr0.5Mo steel, the creep strength of the material affected by PWHT decreased and creep rupture occurred approximately 30% sooner than in the material exposed to service and unaffected by the weld repair process.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Viswanathan · Power Eng. · 1996 · 100 · 38
2. Parker · Mater. Sci. Technol. · 1995 · 11 · 126710.1179/mst.1995.11.12.1267 ↗
3. ASME. Boiler and Pressure Vessels Code. Section I. Rules for Construction of Power Boilers, 1983.
4. R. Viswanathan, Damage mechanisms and life assessment of high temperature components, ASM International, Metals Park, OH, 1989, p. 497.10.31399/asm.tb.dmlahtc.9781627083409 ↗
5. R. Fernández, Ph.D. Thesis, Federal University of São Carlos, São Carlos, Brazil, 2000.
6. Norris · J. Pressure Vessels Piping · 1996 · 67 · 32910.1016/0308-0161(95)00057-7 ↗
7. Yang · Mater. Charact. · 1993 · 30 · 7510.1016/1044-5803(93)90011-J ↗
8. L. Toft, A. Mardsen, in: Conference on Structural Processes in Creep, Special Report No. 70, The Iron and Steel Institute, London, 1963, p. 276.
9. Baker · J. Iron Steel Inst. · 1959 · 192 · 257
10. Afrouz · Metals Technol. · 1983 · 10 · 46110.1179/030716983803291569 ↗
11. Woodhead · J. Iron Steel Inst. · 1965 · 203 · 605
12. I. Novikov, Teoria dos Tratamentos Térmicos dos Metais, UFRJ, Rio do Janeiro, 1994, p. 550.
13. R. Honeykombe, Aços, microestrutura e propriedades, Fundação Calouste Gulbenkian, Lisboa, 1985, 346 pp.
14. Tanino · J. Iron Steel Inst. · 1967 · 205 · 874
15. B. Cane, M. Askins, M. Shammas, Report on phase 1, task 1—Examination of CEGB header samples—Estimating the remanent life of boiler pressure parts—EPRI Contract 2253-1, Final Report, 1987.
16. Chaudhuri · Acta Metall. · 1993 · 41 · 27310.1016/0956-7151(93)90358-Y ↗
17. Robson · Mater. Sci. Technol. · 1997 · 13 · 63110.1179/mst.1997.13.8.631 ↗
18. Dyson · J. Iron Steel Inst. · 1964 · 202 · 325
19. Parker · J. Pressure Vessels Piping · 1995 · 63 · 4510.1016/0308-0161(94)00047-M ↗
20. Liaw · Mater. Sci. Technol. · 1991 · 131A · 187
21. Viswanathan · Metall. Trans. · 1977 · 8A · 87710.1007/BF02661568 ↗
22. M. Collins, in: Proceedings on a Meeting on Creep Strength IN Steel and High Temperature Alloys, 20–22 September 1972, The Iron and Steel Institute, London, 1972, p. 217.
23. F. Clauss, Engineer’s Guide to High Temperature Materials. Reading, Addisson-Wesley, Mass, 1969, p. 401.