Microstructure of dense thin sheets of γ-TiAl fabricated by hot isostatic pressing of tape-cast monotapes
Source abstract
Abstract
Abstract A powder metallurgy route based on hot isostatic pressing (HIP) of tape-cast monotapes was used for the direct fabrication of dense thin sheets (250–300 μm thick) of gamma titanium aluminide (γ-TiAl). Polarized light microscopy revealed a fine-grained microstructure (average grain size ∼3 μm) but a few isolated larger grains (∼20 μm) were also present. The primarily metastable α 2 microstructure of the rapidly solidified starting powder transformed to the equilibrium near-γ microstructure during HIP at 1100 °C. Chemical analysis revealed that the dense sheet had a carbon content of 0.13 wt.%, which was only 0.04 wt.% higher than that of the starting powder, but the oxygen content was significantly higher, presumably introduced during the decanning step. The hardness measured using Vickers microindentation technique was 384 ± 9 HV. Manipulation of the as-HIPed microstructure was performed by heating for up to 1 h in flowing argon at temperatures (1170–1385 °C) below and above the alpha transus (1355 °C). Below 1250 °C, limited grain growth and no discernable change in the as-HIPed (near-γ) microstructure occurred. Sheets heated to 1320 °C and 1365 °C had a duplex microstructure of γ and α 2 grains, with some lamellar grains. Except for a thin surface layer (20–30 μm thick), the microstructure of the heat-treated sheet was uniform, but a fully lamellar microstructure was not achieved even after heating for 1 h at 1385 °C.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Kim · JOM · 1989 · 41 · 2410.1007/BF03220267 ↗
2. Kim · JOM · 1991 · 43 · 4010.1007/BF03221103 ↗
3. Froes · J. Mater. Sci. · 1992 · 27 · 511310.1007/BF02403806 ↗
4. The development of sheet gamma TiAl technology under the enabling propulsion materials/high speed civil transport (EPM/HSCT) program
5. Wrought processing of ingot metallurgy gamma titanium aluminide alloys
6. S.L. Semiatin, S.M. El-Soudani, D.C. Vollmer, C.R. Thompson, Thermomechanical processing of ingot metallurgy near gamma titanium aluminides to refine grain size and optimize mechanical properties, US Patent 5,442, 847, (August 1995).
7. Processing and mechanical properties of γ-TiAl based alloy sheet material
8. Koeppe · Mater. Sci. Eng. · 1995 · A201 · 18210.1016/0921-5093(94)09754-2 ↗
9. Clemens · Z. Metallkd. · 1995 · 86 · 814
10. Moll · Met. Powder Rep. · 2000 · 55 · 1810.1016/S0026-0657(00)87337-3 ↗
11. Processing of intermetallic alloys
12. Semiatin · Mater. Sci. Eng. · 1994 · A185 · 4510.1016/0921-5093(94)90926-1 ↗
13. Semiatin · Metall. Trans. · 1992 · 23A · 14910.1007/BF02660861 ↗
14. Semiatin · Metall. Trans. · 1993 · 24A · 129510.1007/BF02668198 ↗
15. Gas-atomized γ-titanium aluminide based alloys—processing, microstructure, and mechanical properties
16. Das · JOM · 2004 · 56 · 4210.1007/s11837-004-0251-y ↗
17. Effect of processing on properties of rolled gamma titanium aluminide sheet made from powder metallurgy plate
18. Rahaman · Mater. Sci. Eng. · 2003 · A360 · 16910.1016/S0921-5093(03)00436-2 ↗
19. Qualitative and quantitative surface microscopy
20. Processing, microstructure and tensile properties of γ-TiAl PM alloy 395MM
21. Powder metallurgy processing of gamma titanium aluminide
22. S.L. Semiatin, Private communication.