journal article·2004-10

Overspray injection in spray forming of CuSn13.5 billets

Alexander Schneider, Volker Uhlenwinkel, Helmuth Harig, Klaus Bauckhage

Publisher page

Abstract

Abstract In the conventional spray forming process the yield, i.e. the ratio of the deposited material mass to the atomized melt mass, ranges from 50 to 80%. The feedback of overspray to the process by means of injection into the spray cone has several promising advantages, including increase of the overall yield, decrease of gas consumption, and reduction of segregation. However, overall porosity increases. Several CuSn13.5 billets were spray-formed with varied Powder to Melt mass flow Ratio (PMR) of 0, 0.1, 0.2 and 0.3, varied Gas to Melt mass flow Ratio (GMR) of 0.7 to 0.56 and varied particle sizes of the injected overspray powders (different sieving fractions from 0 to 300 μm). Analyses of the microstructure, porosity, radial segregation of Sn, and the yield were carried out and correlated with the process parameters.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Heat Transfer Mechanisms · High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. E. Lavernia, Y. Wu, Spray Atomization and Deposition, John Wiley & Sons, 1996.
2. A. Lawley, Proceedings of International Conference on Spray Deposition and Melt Atomization—SDMA, Bremen, 2000, p. 3.
3. Grant · Prog. Mater. Sci. · 1995 · 39 · 49710.1016/0079-6425(95)00004-6 ↗
4. K. Hummert, Spray Forming—Kolloquium des SFB 372, vol. 1, University of Bremen, 1996, p. 199.
5. K. Schimanski, A. Schulz, et al., Spray Forming—Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 193.
6. C. Kramer, Die Kompaktierungsrate beim Sprühkompaktieren von Gaußförmigen Depsotis, Ph.D. Thesis, University of Bremen, 1997.
7. M. Buchholz, Untersuchung des Kompaktierverhaltens an sprühkompaktierten Bolzen, Ph.D. Thesis, University of Bremen, 2002.
8. A. Schneider, O. Meyer, et al., Spray Forming—Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 155.
9. Convective heat transfer from a billet due to an oblique impinging circular jet within the spray forming process10.1016/S1290-0729(03)00022-X ↗
10. V. Uhlenwinkel, A. Schneider, et al., Effect of Particle Injection during Spray Forming of Cu–Sn Billets, PM2TEC, Orlando, 2002.
11. A. Schneider, R. Klein, V. Uhlenwinkel, H. Henein, Investigation of Local Particle Mass Flux in a Jet Stream with an Isokinetic Probe Symposium Spray Forming SFB 372, vol. 6, University of Bremen, 2002, p. 111.
12. H. Müller, S. Hansmann, K. Ohla, Proceedings of the International Conference on Spray Deposition and Melt Atomization—SDMA, Bremen, 2000, p. 205.
13. K. Ohla, H. Müller, M. Keppeler, Spray Forming of CuSn13–17, PM2TEC, New Orleans, 2001.
14. A. Schneider, V. Uhlenwinkel, K. Bauckhage, Spray Forming—Kolloquium des SFB 372, vol. 5, University of Bremen, 2001, p. 69.
15. A. Schneider, V. Uhlenwinkel, et al., Proceedings of the International Conference on Spray Deposition and Melt Atomization—SDMA, Bremen, 2000, p. 219.
16. A. Schneider, V. Uhlenwinkel, et al., Spray Forming of MMC—Study on the Particle Distribution in CuNi2Si Billets with Graphite, PM2TEC, New Orleans, 2001.
17. Mingard · Acta Mater. · 2000 · 48 · 243510.1016/S1359-6454(00)00075-6 ↗