journal article·2005-10

Effect of mechanical properties on the wrinkling behaviour of three different commercially pure aluminium grades when drawn through conical and tractrix dies

C. Loganathan, R. Narayanasamy

Materials Science and Engineering: A· Volume 406· Issue 1-2
Publisher page

Abstract

Abstract Experiments have been carried out to evaluate the onset of wrinkling behaviour in three grades of annealed commercially pure aluminium sheets, namely ISS 19000, ISS 19600 and ISS 19660, having thickness 2.00 mm, while drawing them through conical and tractrix dies. The deep drawing of circular blanks of different diameters of the aforesaid sheet metals was carried out using flat bottom punch. The analysis of the experimental data has revealed that the onset of wrinkling takes place when the ratio of the plastic strain increments (dɛr/dɛθ) reached a critical value. It was further found that the measured strains followed non-linear paths in the wrinkling limit diagrams. Further it was observed that the aluminium grade having high strain hardening index value, low yield stress and high normalized hardening rate shows better resistance against wrinkling. Drawing with the tractrix die showed better resistance against wrinkling compared with drawing with the conical die.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Laser and Thermal Forming Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. Hutchinson · Adv. Appl. Mech. · 1974 · 14 · 6710.1016/S0065-2156(08)70031-0 ↗
2. Neale · Int. J. Methods Eng. · 1990 · 30 · 159510.1002/nme.1620300816 ↗
3. Kim · J. Mater. Process. Technol. · 2000 · 97 · 8810.1016/S0924-0136(99)00346-5 ↗
4. de Magalhaes · Int. J. Mech. Sci. · 2003 · 45 · 116710.1016/j.ijmecsci.2003.08.001 ↗
5. Ameziane-Hassani · Int. J. Mech. Sci. · 1991 · 33 · 1310.1016/0020-7403(91)90024-W ↗
6. T. Balun, P. Ling, M.M.K. Lou, S.C. Tang, Detection and elimination of wrinkles on an Auto-body Panel by the Binder Set Analysis, SAE Tech. Pap. Series 930515, 1993.10.4271/930515 ↗
7. Cao · Int. J. Struct. · 1997 · 34 · 15310.1016/S0020-7683(96)00008-X ↗
8. Gunasekara · 1982 · 173
9. S.P. Keelar, P.A. Stine, Simulation the sheet metal forming process—an optimization exercise on the PC or Engineering Work station, SAE Tech. Pap. Series 890345, pp. 25–36, 1989.10.4271/890345 ↗
10. Mazilu · 1987 · 263
11. Narayanasamy · J. Mater. Process. Technol. · 1995 · 49 · 19910.1016/0924-0136(94)01331-T ↗
12. Sobis · Int. J. Mater. Process. Technol. · 1992 · 7 · 273
13. Szacinzki · J. Mater. Process. Technol. · 1991 · 25 · 12510.1016/0924-0136(91)90085-S ↗
14. Szacinzki · J. Mater. Process. Technol. · 1991 · 7 · 224
15. Traversion · J. Mater. Process. Technol. · 1995 · 25 · 30610.1016/0924-0136(94)01389-I ↗
16. Thomson · 1987 · 61
17. Wang · Int. J. Mater. Process. Technol. Sci. · 1994 · 36 · 945
18. Wang · J. Eng. Mater. Technol. · 1989 · 111 · 23510.1115/1.3226460 ↗
19. M. Karima, R. Sowerby, Report No.144, Faculty of Engineering, McMaster Univ., 1980.
20. Narayanasamy · J. Mater. Process. Technol. · 1994 · 41 · 27510.1016/0924-0136(94)90166-X ↗
21. Di · J. Test. Eval. · 1997 · 25 · 7410.1520/JTE11327J ↗
22. Wang · J. Mater. Process. Technol. · 2000 · 105 · 21510.1016/S0924-0136(00)00534-3 ↗
23. M. Karima, Ph.D. Thesis, McMaster University, Canada, 1981.
24. Gall · 1967
25. R. Narayanasamy, Ph.D. Thesis, Regional Engineering College, Tiruchirappalli 620 015, India, 1992.