journal article·2006-02

Microstructures and mechanical properties of spray-formed and squeeze-cast Al–25Si–0.89Cu–1.0Ni–0.84Mg alloys in solutionized and aged conditions

C.-H. Chiang, Chi Y.A. Tsao

Materials Science and Engineering: A· Volume 417· Issue 1-2
Publisher page

Abstract

Abstract The microstructures and mechanical properties of spray-formed and squeeze-cast Al–25Si–0.89Cu–1.0Ni–0.84Mg alloys in solutionized and aged conditions were compared. DSC analysis was used to study the degree of supersaturation between the spray-formed and squeeze-cast alloys, and the tensile properties of extruded spray-formed alloy in various heat treatment conditions were investigated. The as-spray-formed alloy exhibits more uniform and finer microstructures than the as-squeeze-cast alloy. The Al 2 Cu was the main phase involved in the solutionizing and aging heat treatment. DSC analysis showed the spray-formed alloy had higher degree of supersaturation than the squeeze-cast alloy. For the same heat treatment condition, the matrix microhardness of spray-formed alloy is higher than that of squeeze-cast alloy. The aging hardening curves reveal two peaks and the time to peaks for the spray-formed alloy is shorter than that for the squeeze-cast alloy. The peak-aged spray-formed alloy exhibits an ultimate strength of 366.0 MPa, a yield strength of 235.3 MPa and an elongation of about 3.4%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Bauxite Residue and Utilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Matsuura · Mater. Chem. Phys. · 2003 · 81 · 39310.1016/S0254-0584(03)00030-0 ↗
2. Li · J. Mater. Sci. Lett. · 2002 · 21 · 53710.1023/A:1015400820191 ↗
3. Zhou · J. Mater. Sci. · 1999 · 34 · 506710.1023/A:1004752815007 ↗
4. Timmermans · Wear · 1999 · 230 · 10510.1016/S0043-1648(98)00336-6 ↗
5. Chien · Mater. Lett. · 2002 · 52 · 33410.1016/S0167-577X(01)00418-9 ↗
6. Wang · J. Mater. Process. Technol. · 2003 · 137 · 19110.1016/S0924-0136(02)01074-9 ↗
7. Ha · J. Mater. Process. Technol. · 2002 · 130 · 69110.1016/S0924-0136(02)00750-1 ↗
8. Kim · J. Alloys Compd. · 2000 · 308 · 23710.1016/S0925-8388(00)00810-0 ↗
9. Wu · Metall. Mater. Trans. A · 1995 · 26A · 123510.1007/BF02670618 ↗
10. Estrada · J. Mater. Sci. · 1990 · 25 · 138110.1007/BF00585454 ↗
11. Su · Mater. Sci. Eng. A · 2004 · A364 · 30510.1016/j.msea.2003.08.043 ↗
12. Chiang · Key Eng. Mater. · 2003 · 249 · 18910.4028/www.scientific.net/KEM.249.189 ↗
13. Li · J. Mater. Sci. · 2003 · 38 · 120310.1023/A:1022857703995 ↗
14. Gupta · J. Mater. Process. Technol. · 1995 · 54 · 26110.1016/0924-0136(95)01797-6 ↗
15. Gomes · Mater. Trans., JIM · 1998 · 39 · 35710.2320/matertrans1989.39.357 ↗
16. Gupta · Mater. Sci. Technol. · 1989 · 5 · 5210.1179/mst.1989.5.1.52 ↗
17. Prasad · J. Mater. Sci. Lett. · 1991 · 10 · 141210.1007/BF00735694 ↗
18. Gupta · J. Alloys Compd. · 1999 · 287 · 28410.1016/S0925-8388(99)00062-6 ↗
19. Song · Mater. Sci. Eng. A · 1995 · A201 · 25110.1016/0921-5093(95)09781-3 ↗
20. John D. Verhoeven, Fundamentals of Physical Metallurgy, John Wiley & Sons, Inc., Singapore, pp. 373–381.
21. Starink · Metall. Mater. Trans. A · 1991 · 22A · 66510.1007/BF02670289 ↗
22. Takeda · Scripta Mater. · 1999 · 41 · 64310.1016/S1359-6462(99)00137-2 ↗
23. Mocellin · J. Mater. Sci. · 1993 · 28 · 485510.1007/BF00361147 ↗
24. Dieter · 1988