journal article·2005-02

The processing phenomena of semisolid Mg–9% Al–1% Zn alloy at ultra high contents of the unmelted phase

F. Czerwinski

Materials Science and Engineering: A· Volume 392· Issue 1-2
Publisher page

Abstract

Abstract A prototype system was used to process the semisolid Mg–9% Al–1% Zn alloy with a content of 75–85% of the unmelted phase. The influence of operating parameters on mold filling characteristics, integrity and microstructure of the component with a weight of 0.5 kg, varying geometry and wall thickness, was examined. The mold filling time was found to be the primary factor controlling the process. Although the turbulent flow created porosity at intermediate stages of mold filling, highly dense structures were obtained unless the injection velocity was high enough to preserve the semisolid state until the final densification. A laminar flow of the slurry, observed for lower injection velocities, resulted in a low porosity at all stages of the mold filling. The final microstructure was dominated by near globular primary α-Mg particles with a size of 40 μm which, for thicker walls, evolved into equiaxed grains. For high injection velocities and large distances from the gate, an inhomogeneity in distribution of α-Mg was detected. The eutectics of the secondary α-Mg and Mg 17 Al 12 with a volume fraction of 15–25%, existed as thin films at particle boundaries and islands at triple junctions. Some suggestions for the processing of magnesium alloys at ultra high solid contents are defined.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. N.L. Bradley, et al., Method and apparatus for the injection molding of metal alloys, US Patent US5040589 (1991).
2. Spencer · Metall. Trans. · 1972 · 3A · 192510.1007/BF02642580 ↗
3. Carnahan · 1999
4. Hartmann · 1999 · 7
5. Metz · Trans. Am. Foundrymen's Soc. · 1969 · 77 · 329
6. Decker · 1996 · 221
7. Czerwinski · Acta Mater. · 2002 · 50 · 326710.1016/S1359-6454(02)00148-9 ↗
8. Aghion · 1997 · 313
9. Wolfsdorf-Brenner · Metall. Mater. Trans. · 1999 · 30A · 195510.1007/s11661-999-0006-z ↗
10. Czerwinski · Acta Mater. · 2001 · 49 · 122510.1016/S1359-6454(01)00015-5 ↗
11. Underwood · 1970
12. Magnesium Die Casting Handbook, NADCA Publication, Rosemont, IL, 1998.
13. Flemings · Metall. Trans. · 1991 · A22 · 95710.1007/BF02661090 ↗
14. Roberts · 1960
15. Uggowitzer · 2000 · 429
16. Dieter · 1976
17. Yang · Scripta Metall. Mater. · 1994 · 30 · 154110.1016/0956-716X(94)90305-0 ↗
18. Basner · Metall. Mater. Trans. · 2000 · 31A · 5710.1007/s11661-000-0052-z ↗
19. M.T. Murray, M.A. Cope, Magnesium Pressure Casting, Patent PCT/AU98/00987 (1998).