journal article·2026-09Open access

Distinct creep behavior of martensite and ferrite in a Si-enriched heat resistance (SEHR) steel at 650/700°C

Jun Zhang, Fanao Meng, Xinhao Zhang, Hao Ren, Decang Zhang, Yingxue Chen, Xiaoxin Zhang, Feifei Zhang, Qingzhi Yan

Abstract

Si-enriched heat resistance (SEHR) steel with a high content of Si (≥1.0 wt%) exhibits excellent corrosion resistance in steam and liquid metal environments. This Si addition introduces high fraction of ferrite into the matrix. However, the insufficient understanding of the creep behavior of this dual phase material hinders further property optimization. Here, we investigate the creep behavior of a SEHR steel containing 17% ferrite at 650/700 °C under the same applied stress of 100 MPa. A similar slope is observed in both the 650 °C and 700 °C samples during the tertiary creep stage in the creep rate-strain relationship, indicating strain-controlled creep behavior. This similarity in tertiary creep slopes is related to the comparable evolution of grain boundary density with strain. The acceleration of creep rate in the tertiary stage is closely associated with sub-grain formation, which proceeds through distinct mechanisms in martensite and ferrite. In martensite, dislocations are intensively recovered, and bugle nucleation and growth occur during creep; consequently, the transformation from laths to sub-grains is a typical recrystallization process. In contrast, in ferrite, the geometrically necessary dislocation (GND) density progressively increases with increasing strain. These newly formed GNDs coalesce to form new sub-boundaries, subdividing the initial large sub-grains into finer ones. This mechanism is characteristic of continuous dynamic recrystallization (CDRX). The fewer large precipitates, lower initial dislocation density, and more severe deformation in ferrite compared to martensite provide favorable conditions for CRDX process. High creep strain promotes the formation of Si-layer around M 23 C 6 carbides which in turn suppresses the further growth of the carbides. These findings elucidate the key factors governing creep behavior in dual phase materials and offer a basis for the further optimization of SEHR steel.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Metallurgical and Alloy Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. Materials challenges in nuclear energy10.1016/j.actamat.2012.11.004 ↗
2. New martensitic steels for fossil power plant: creep resistance10.1134/S0031918X10020110 ↗
3. Modified Z-phase formation in a 12% Cr tempered martensite ferritic steel during long-term creep10.1016/j.msea.2022.143857 ↗
4. Zener pinning pressure in tempered martensite lath structure10.4028/www.scientific.net/MSF.715-716.745 ↗
5. Creep behavior of a 10%Cr heat-resistant martensitic steel with low nitrogen and high boron contents at 650 °C10.1016/j.msea.2019.138353 ↗
6. Creep strength breakdown and the change in back stress strengthening in 10 % Cr martensitic steels during creep at 923 K10.1016/j.msea.2024.146577 ↗
7. On the effect of tempering temperature on the long-term creep behavior of a 10% Cr steel with low nitrogen and high boron contents10.1016/j.msea.2023.145912 ↗
8. Evolution of microstructure and deformation resistance in creep of tempered martensitic 9–12%Cr–2%W–5%Co steels10.1016/j.actamat.2006.02.038 ↗
9. Analysis of creep rates of tempered martensitic 9%Cr steel based on microstructure evolution10.1016/j.msea.2008.04.118 ↗
10. Evolution of dislocation density, size of subgrains and MX-type precipitates in a P91 steel during creep and during thermal ageing at 600C for more than 100,000h10.1016/j.msea.2010.03.010 ↗
11. On the 650 °C thermostability of 9–12Cr heat resistant steels containing different precipitates10.1016/j.actamat.2017.05.069 ↗
12. On the origin of the superior long-term creep resistance of a 10% Cr steel10.1016/j.msea.2017.12.066 ↗
13. Laves-phase precipitates in a low-carbon 9% Cr martensitic steel during aging and creep at 923K10.1016/j.msea.2014.07.046 ↗
14. Improving toughness and strain-hardening of a silicon-enriched ferritic/martensitic (F/M) steel via an austenite isothermal hot-rolling (AIHR) process10.1016/j.msea.2023.145411 ↗
15. Synergistic toughening by a layered microstructure and texture of Si-enriched ferritic/martensitic(F/M) heat resistant steel10.1016/j.jmrt.2024.06.039 ↗
16. Effect of distinct ferrite structures on the crack propagation behavior in a Si-enriched ferritic/martensitic (F/M) steel under low-cycle fatigue (LCF) at 600 °C10.1016/j.ijfatigue.2026.109517 ↗
17. Microstructure and creep rupture of P92-grade weld metal10.1007/BF03321294 ↗
18. Effect of ferrite content on the creep strength of 12Cr-2Mo-0.08C boiler tubing steels10.1007/BF02833482 ↗
19. Brief study on δ-ferrite characterization: a review10.1016/j.matpr.2021.08.280 ↗
20. Effect of Delta ferrite on microstructure and mechanical properties of high-chromium martensitic steel10.1007/s11665-019-3862-8 ↗
21. On the formation and growth of Mo-rich laves phase particles during long-term creep of a 12% chromium tempered martensite ferritic steel10.1016/j.scriptamat.2009.08.031 ↗
22. On the nucleation of laves phase particles during high-temperature exposure and creep of tempered martensite ferritic steels10.1016/j.actamat.2014.08.008 ↗
23. On laves phase in a 9Cr3W3CoB martensitic heat resistant steel when aged at high temperatures10.1016/j.jmst.2020.12.062 ↗
24. Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues10.1016/S1359-6462(02)00335-4 ↗
25. Cyclic softening behavior of a Si-enriched ferritic/martensitic (F/M) steel10.1016/j.msea.2025.149264 ↗
26. Creep modeling and creep life estimation of Gr.9110.3139/146.110769 ↗
27. The microstructure evolution and its effect on creep behaviors in P92 steel under different stresses10.1016/j.matchar.2023.112744 ↗
28. Structural changes of tempered martensitic 9%Cr–2%W–3%Co steel during creep at 650°C10.1016/j.msea.2011.12.020 ↗
29. The formation of dislocation networks10.1016/0039-6028(72)90270-1 ↗
30. On the origin of high stresses in subboundaries during the creep of aluminium10.1016/0025-5416(86)90274-0 ↗
31. The production and utility of recovered dislocation substructures10.1007/BF02661562 ↗
32. Coarsening behavior of lath and its effect on creep rates in tempered martensitic 9Cr–W steels10.1016/j.msea.2004.01.057 ↗
33. In situ observation of recovery of lath structure in 9% chromium creep resistant steel10.1179/026708303225010696 ↗
34. Experimental measurement of dislocation density in metallic materials: a quantitative comparison between measurements techniques (XRD, R-ECCI, HR-EBSD, TEM)10.1016/j.matchar.2023.112842 ↗
35. Mechanism-based modeling of thermal and irradiation creep behavior: an application to ferritic/martensitic HT9 steel10.1016/j.ijplas.2019.11.012 ↗
36. The deformation of plastically non-homogeneous materials
37. Nano-sized MX carbonitrides contribute to the stability of mechanical properties of martensite ferritic steel in the later stages of long-term aging10.1016/j.actamat.2019.06.012 ↗
38. The nucleation of Mo-rich laves phase particles adjacent to M23C6 micrograin boundary carbides in 12% Cr tempered martensite ferritic steels10.1016/j.actamat.2015.01.027 ↗
39. The effect of phase parameter variation on hardness of P91 components after service exposures at 530–550 °C10.1016/j.actamat.2017.10.010 ↗
40. Effect of ferritic hot rolling process on microstructure and properties of IF steel10.4028/www.scientific.net/MSF.993.505 ↗
41. Effect of stored energy and recovery on the overall recrystallization kinetics of a cold rolled low carbon steel10.1016/j.msea.2007.07.077 ↗
42. On the effect of long-term creep on the microstructure of a 12% chromium tempered martensite ferritic steel10.1016/j.actamat.2009.07.010 ↗
43. Irradiation-induced segregation/desegregation at grain boundaries of a ferritic Fe-Mn-Si steel10.1016/j.actamat.2021.117297 ↗
44. Influence of Si on the microstructure and C redistribution in martensitic steels10.1016/j.matdes.2023.111875 ↗
45. Effect of thermal aging at 550 °C on microstructure and mechanical properties of a 9Cr martensitic steel with high silicon content10.1016/j.matchar.2023.113045 ↗
46. M23C6 precipitation and Si segregation promoted by deep cryogenic treatment aggravating pitting corrosion of supermartensitic stainless steel10.1007/s42243-020-00514-w ↗
47. Formation of delta-ferrite and its effect on impact toughness of GTAW weld metals in a 12 wt-% Cr steel10.1080/13621718.2022.2148063 ↗
48. Effect of thermal treatment on the evolution of delta ferrite in 11Cr–3Co–2.3W steel10.1080/02670836.2018.1510072 ↗
49. Kinetics modeling of delta-ferrite formation and retainment during casting of supermartensitic stainless steel10.1016/j.matdes.2017.01.026 ↗
50. Laves-phase evolution during aging in 9Cr-1.8W-0.5Mo-VNb steel for USC power plants10.1016/j.matchemphys.2015.07.032 ↗
51. Influence of laves phase on creep strength of modified 9Cr-1Mo steel10.1016/j.msea.2017.08.111 ↗
52. High stresses in subboundaries and unknitting of dislocations from subboundaries in creep10.1016/0025-5416(87)90586-6 ↗
53. Subgrain boundary migration during creep of lif: I. Recombination of subgrain boundaries10.1080/01418619208201548 ↗
54. Tempering of Lath martensite in low and medium carbon steels: assessment and challenges10.1002/srin.201700038 ↗
55. Recrystallization of Lath martensite with bulge nucleation and growth mechanism10.2355/isijinternational.41.1047 ↗
56. Influence of cold working on recovery and recrystallization of lath martensite in 0.2%C steel10.2320/matertrans1989.33.577 ↗
57. The nucleation of recrystallization at second phase particles in deformed aluminium10.1016/0001-6160(77)90109-2 ↗
58. Particle stimulated nucleation in coarse-grained ferritic stainless steel10.1007/s11661-012-1408-x ↗
59. Disparity in recrystallization of α- & γ-fibers and its impact on cube texture formation in non-oriented electrical steel10.1016/j.actamat.2021.117141 ↗
60. Hot ductility and microstructure in casted 2205 duplex stainless steels10.1016/j.msea.2009.02.022 ↗
61. A model of continuous dynamic recrystallization10.1016/S1359-6454(03)00078-8 ↗
62. Dynamic recrystallization behavior and interfacial bonding mechanism of 14Cr ferrite steel during hot deformation bonding10.1016/j.jmst.2020.01.010 ↗
63. Improved recrystallization resistance by ferrite and carbide in a ferritic/martensitic (F/M) steel10.1016/j.jmrt.2025.09.106 ↗