Synergistic effect of low heat input rotary friction welding and post-weld heat treatment on strength enhancement of AA6061-T6511 joints
Source abstract
Abstract
This study elucidates how the synergistic combination of a low heat input rotary friction welding (LHI RFW) process and post-weld heat treatment (PWHT) governs the microstructure and mechanical properties of AA6061-T6511 joints. Conventional RFWed (CON RFW) joints suffer from severe thermal softening due to high-temperature dislocation annihilation and precipitate dissolution, which drastically reduces the joint efficiency. In contrast, the developed LHI technique lowers the peak interfacial temperature by approximately 100 °C compared to CON RFW. This significant thermal reduction effectively preserves a greater fraction of strengthening β'' precipitates and dislocation networks in the as-welded state, thereby enhancing the initial joint integrity. Subsequent rapid PWHT at 210 °C for 10 min triggers markedly different strengthening pathways. CON RFWed joints show minimal improvement because the strength loss from GP zone dissolution is not adequately compensated by very limited new precipitation. Conversely, in LHI joints, the retained dislocations actively accelerate precipitation kinetics via dislocation-assisted diffusion and nucleation during ageing. This effective microstructural coupling between preserved dislocations and optimized precipitate formation enables the joint efficiency approaching 98.6%. A quantitative strengthening model confirms that in LHI joints after PWHT, dislocation hardening remains the dominant mechanism, while a substantial increase in precipitation hardening works synergistically to drive the superior, near-complete recovery of the joint strength.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Magnesium Alloys: Properties and Applications · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Environmentally responsible lightweight passenger vehicle design and manufacturing10.1007/s42154-023-00241-4 ↗
2. The use of aluminum alloys in structures: review and outlook10.1016/j.istruc.2023.105290 ↗
3. Recent developments in joining of aluminum alloys10.1007/s00170-016-9861-0 ↗
4. Optimization of continuous drive friction welding process for AA6061-T6 circular pipe and conical head10.1016/j.istruc.2021.12.065 ↗
5. Linear and rotary friction welding review10.1080/09506608.2015.1109214 ↗
6. Effect of rotation speed on friction behavior of rotary friction welding of AA6061-T6 aluminum alloy10.1007/s40194-018-0601-y ↗
7. Microstructural and mechanical properties of Al–Mg–Si–Cu joint fabricated by rotary friction welding10.1016/j.jmrt.2023.10.201 ↗
8. Statistical analysis of optimum friction welding conditions for 6061 aluminium alloy friction-welded joints10.1533/wint.2005.3349 ↗
9. Effect of friction welding conditions and aging treatment on mechanical properties of A7075-T6 aluminium alloy friction joints10.1179/174329305X44125 ↗
10. Effect of heat treatment on the microstructure and mechanical properties of rotary friction welded AA7075 and AA5083 dissimilar joint10.3390/ma16062464 ↗
11. Artificial ageing heat treatment post-effect on profile and mechanical properties of the AA 6061 friction welding joint10.1088/1757-899X/1034/1/012134 ↗
12. Effect of post-weld heat treatment on inhomogeneity of mechanical properties and corrosion behavior of rotary friction welded 2024 aluminum alloy joint10.1016/j.jmapro.2022.01.059 ↗
13. A study on optimizing the parameters of the heat treatment process on rotary friction welding of aluminum alloy A606110.4028/p-o0LhWr ↗
14. Effect of reheating after low temperature pre-ageing on microstructure of 6061 aluminum alloy10.2320/matertrans.MT-L2021014 ↗
15. Principle for obtaining high joint quality in dissimilar friction welding of Ti-6Al-4V alloy and SUS316L stainless steel10.1016/j.jmst.2019.10.037 ↗
16. A novel multi-stage pressuring strategy to fabricate sound high-carbon steel joints in rotary friction welding10.1016/j.jmapro.2024.11.101 ↗
17. Ultralow rotation speed produces high-quality joint in dissimilar friction welding of Ti–6Al–4V alloy and SUS316L stainless steel10.1016/j.msea.2020.140303 ↗
18. Material properties of normal and high strength aluminium alloys at elevated temperatures10.1016/j.tws.2019.01.012 ↗
19. Effects of plunge depth on macro-/microstructure and mechanical properties of refill friction stir spot welded 2195-T6 Al–Li alloy10.1016/j.jmrt.2025.02.046 ↗
20. High-strength and crack-free welding of 2024 aluminium alloy via Zr-core-Al-shell wire10.1038/s41467-024-45660-x ↗
21. Improving long-term thermal stability in twin-roll cast Al-Mg-Si-Cu alloys by optimizing Mg/Si ratios10.1016/j.jmst.2024.04.017 ↗
22. Perforation of AA6061-T651 plates by 4340 steel ogive-nose rods with normal impacts
23. Effect of different friction coefficient models on numerical simulation of inertia friction welding of 2219 Al alloy to 304 stainless steel10.1016/j.jmrt.2023.11.079 ↗
24. Analysis of transient temperature and residual thermal stresses in friction stir welding of aluminum alloy 6061-T6 via numerical simulation10.1007/s00170-010-3038-z ↗
25. Heat-pattern induced non-uniform radial microstructure and properties of Ti-6Al-4V joint prepared by rotary friction welding10.1016/j.matchar.2022.112536 ↗
26. Effects of the CFRP hole expansion on the fatigue performance and failure mechanism of CFRP/Ti single-lap bolted joints10.1016/j.compositesa.2026.109801 ↗
27. Transition of interfacial friction regime and its influence on thermal responses in rotary friction welding of SUS304 stainless steel: a fully coupled transient thermomechanical analysis10.1016/j.jmapro.2022.08.016 ↗
28. Experimental and analytical investigation on friction welding dissimilar joints for aerospace applications10.1016/j.asej.2022.101853 ↗
29. Enhancing the recrystallization resistance and strength-ductility trade-off of Al–Mg–Si–Cu–Mn alloys by three-step homogenization10.1016/j.msea.2024.146420 ↗
30. Screw extrusion-plasticizing friction stir deposition of pure aluminum: a novel solid-state additive manufacturing approach with particulate feedstock
31. A general mechanism of grain growth ─Ⅰ. Theory10.1016/j.jmat.2021.02.007 ↗
32. Study on the effect of aging heat treatment temperature on the microstructure and properties of soluble Al-Zn-Mg-Ga-In-Sn aluminum alloys in solid solution state10.1016/j.jallcom.2024.176048 ↗
33. Study of the precipitate evolution mechanism in an Al-Mg-Si-Cu alloy with Si-rich and low Cu composition10.1016/j.matchar.2022.112167 ↗
34. Understanding the precipitation mechanism of copper-bearing phases in Al-Mg-Si system during thermo-mechanical treatment10.1016/j.jmst.2021.04.026 ↗
35. Nano-phase transformation of composite precipitates in multicomponent Al-Mg-Si(-Sc) alloys10.1016/j.jmst.2021.09.037 ↗
36. Analysis of the evolution of Mg2 Si precipitates during continuous cooling and subsequent re-heating of a 6061 aluminum alloy with differential scanning calorimetry and a simple model10.1515/ijmr-2021-8443 ↗
37. A DSC study on the precipitation kinetics of cryorolled Al 6063 alloy10.1016/j.matchemphys.2010.02.032 ↗
38. Simultaneously enhanced strength and ductility of 6xxx Al alloys via manipulating meso-scale and nano-scale structures guided with phase equilibrium10.1016/j.jmst.2019.09.029 ↗
39. Atomic clusters induced rapid hardening behavior in an early stage of isothermal aging for a high-strength Al alloy produced by laser powder bed fusion additive manufacturing
40. Deformation-mediated cyclic evolution of precipitates in Al-Mg-Si-Cu alloy by multi-pass ECAP and thermal treatments10.1016/j.jmst.2024.05.075 ↗
41. Modelling of the age hardening behaviour of Al–Mg–Si alloys10.1016/S1359-6454(00)00301-3 ↗
42. Characterization of nanocrystalline materials by X-ray line profile analysis10.1007/s10853-006-0696-1 ↗
43. Dislocations, grain size and planar faults in nanostructured copper determined by high resolution X-ray diffraction and a new procedure of peak profile analysis10.1016/S1359-6454(98)00001-9 ↗
44. Self-healing of low angle grain boundaries by vacancy diffusion and dislocation climb10.1016/j.scriptamat.2018.06.035 ↗
45. Enhancing creep formability and comprehensive property in Al–Mg–Si alloy by combinatorial pre-ageing and large pre-deformation10.1016/j.msea.2021.141967 ↗
46. Understanding the role of short-range order in the nucleation and transformation of the B′/Q′ precipitates in Al-Mg-Si(-Cu) alloys10.1007/s11661-021-06309-2 ↗
47. Clustering and precipitation in Al-Mg-Si alloys during linear heating10.1016/j.jmst.2021.11.062 ↗
48. Similar and dissimilar rotary friction welding of steels: a review of microstructural evolution and mechanical properties10.1016/j.jmrt.2025.05.079 ↗
49. Large creep formability and strength–ductility synergy enabled by engineering dislocations in aluminum alloys10.1016/j.ijplas.2020.102774 ↗
50. Comparison between dislocation dynamics model predictions and experiments in precipitation-strengthened Al–Li–Sc alloys10.1016/j.actamat.2014.06.038 ↗
51. Microstructural modelling in friction stir welding of 2000 series aluminium alloys
52. The mechanism of plastic deformation of crystals. Part I.—Theoretical
53. Coupled precipitation and yield strength modelling for non-isothermal treatments of a 6061 aluminium alloy10.1016/j.actamat.2013.09.041 ↗
54. Solid-state bonding process induced highly synergistic mechanical properties of 6061 Al alloy joint by shear deformation10.1016/j.jmst.2023.04.056 ↗
55. The plastic deformation of polycrystalline aggregates