Combined effects of silicon content, prior deformation and partitioning conditions on retained austenite and mechanical properties of a quenched and partitioned 0.4% C advanced high-strength steel
Source abstract
Abstract
Quenching and Partitioning (Q&P) has become one of the established processing routes for producing advanced high-strength steels (AHSS), owing to its ability to engineer microstructures that balance between high strength and ductility through retained austenite (RA) stabilization. However, the alternative Deformation–Quenching and Partitioning (DQ&P) pathway remains relatively underexplored. This study investigates the combined effects of silicon content, prior deformation, and partitioning parameters on RA stabilization and mechanical behavior in two medium-carbon steels (0.4C–2Mn–XSi–1Cr–0.02Al–0.49Ni, wt.%) with Si contents of X=0.25 wt.% (L-Si) and X=1.5 wt.% (H-Si). Three deformation passes (true strain ≈ 0.2/pass) were applied at 850 °C prior to quenching. Partitioning was performed at 250 °C and 300 °C for 1000 s, with additional holding times (10–10000 s) examined for selected conditions. Microstructural evolution was characterized using dilatometry, electron microscopy, and X-ray diffraction; mechanical behavior was evaluated via tensile testing. The high Si content effectively suppressed cementite precipitation and bainite formation, enabling higher RA fractions of ∼20 vol.% at 300 °C and ∼17 vol.% at 250 °C, with 1000 s identified as the optimal partitioning time. In the low-Si steel, ∼14 vol.% RA was obtained at 250 °C after 1000 s, and 17 vol.% after 10000 s. Applied deformation resulted in higher RA fractions compared to non-deformed Q&P steels. However, up to 23 vol.% bainite formed in the low-Si steel at 300 °C, consuming the available austenite. Both steels exhibited pronounced TRIP behavior. The high-Si steel partitioned at 300 °C (1000 s) achieved an excellent strength–ductility balance (1822 MPa and 9.3% elongation), while the low-Si steel partitioned at 250 °C also demonstrated competitive performance, highlighting the positive role of deformation. • DQ&P processing increases retained austenite stability compared with Q&P • High Si (1.5 wt.%) suppresses cementite and bainite, stabilizing up to ∼20 vol.% RA • Prior deformation refines austenite grains and enhances RA stability in low-Si steel • Optimal properties achieved: UTS ≈ 1.8–2.0 GPa with ∼8–9% elongation
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. R Kuziak, R. Kawalla, S. Waengler, Advanced high strength steels for automotive industry, Arch. Civ. Mech. Eng. 8(2): 103–117 DOI:10.1016/S1644-9665(12)60197-6.10.1016/S1644-9665(12)60197-6 ↗
2. The “quenching and partitioning” process: background and recent progress10.1590/S1516-14392005000400010 ↗
3. Partitioning of carbon from supersaturated plates of ferrite, with application to steel processing and fundamentals of the bainite transformation10.1016/j.cossms.2004.09.003 ↗
4. Improved work hardening of a medium carbon-TRIP steel by partial decomposition of retained austenite10.1016/j.msea.2020.140504 ↗
5. Carbon partitioning to austenite from martensite or bainite during the quench and partition (Q&P) process: a critical assessment10.1016/j.actamat.2007.08.051 ↗
6. Carbon partitioning into austenite after martensite transformation10.1016/S1359-6454(03)00059-4 ↗
7. Impact of carbon segregation on transition carbides and cementite precipitation during tempering of low carbon steels: experiments and modeling10.1016/j.actamat.2024.119919 ↗
8. Competitive mechanisms occurring during quenching and partitioning of three silicon variants of 0.4 wt.% carbon steels10.1016/j.jmrt.2021.01.085 ↗
9. Influence of silicon contents on the microstructure and tensile properties of quenching and partitioning (Q&P) processed low carbon steel10.2355/isijinternational.ISIJINT-2023-113 ↗
10. The role of silicon in carbon partitioning processes in martensite/austenite microstructures10.1016/j.matdes.2017.04.080 ↗
11. Effect of silicon addition on carbide transition in tempered martensite of middle carbon steels10.2355/isijinternational.ISIJINT-2023-165 ↗
12. Carbon content evolution in austenite during austenitization studied by in situ synchrotron X-ray diffraction of a hypoeutectoid steel10.1016/j.mtla.2020.100664 ↗
13. Evolution of austenite lattice parameter during isothermal transformation in a 0.4 C low alloyed steel10.1016/j.mtla.2023.101685 ↗
14. Evaluation of the possibility to obtain nanostructured bainite in high-carbon and high-silicon 9XC bearing steel10.1007/s11665-020-05038-8 ↗
15. Effect of Si on bainitic transformation kinetics in steels explained by carbon partitioning, carbide formation, dislocation densities, and thermodynamic conditions10.1016/j.matchar.2022.111774 ↗
16. Effects of Q&P processing conditions on austenite carbon enrichment studied by in situ high-energy X-ray diffraction experiments10.3390/met7070232 ↗
17. The Effect of the Si Content on the Morphology and Amount of Fe2SiO4 in Low Carbon Steels10.3390/met6040094 ↗
18. Interaction of carbon partitioning, carbide precipitation and bainite formation during the Q&P process in a low C steel10.1016/j.actamat.2015.11.032 ↗
19. The role of the austenite grain size in the martensitic transformation in low carbon steels10.1016/j.matdes.2019.107625 ↗
20. Effect of prior austenite grain size on the tensile properties and fracture toughness of nano-structured bainite10.1016/j.matchar.2022.112214 ↗
21. Effect of prior austenite grain size on the morphology of nano-bainitic steels10.1007/s11661-018-4492-8 ↗
22. Thermal stability of retained austenite in TRIP steels studied by synchrotron X-ray diffraction during cooling10.1016/j.actamat.2005.08.017 ↗
23. Near-Ac3 austenitized ultra-fine-grained quenching and partitioning (Q&P) steel10.1016/j.scriptamat.2016.06.003 ↗
24. Designing a novel DQ&P process through physical simulation studies10.4028/www.scientific.net/MSF.762.83 ↗
25. Effect of deformation on microstructure and mechanical properties of medium carbon steel during heat treatment process10.1186/s10033-021-00634-8 ↗
26. Design of tough, ductile direct quenched and partitioned advanced high-strength steel with tailored silicon content10.1016/j.jmrt.2022.01.073 ↗
27. Effect of grain size on thermal and mechanical stability of austenite in metastable austenitic stainless steel10.2355/isijinternational.53.1224 ↗
28. The effect of prior ferrite formation on bainite and martensite transformation kinetics in advanced high-strength steels10.1016/j.actamat.2013.06.043 ↗
29. Evolution of Ms temperature as a function of composition and grain size10.1007/s11661-020-06022-6 ↗
30. Carbon partitioning during quenching and partitioning heat treatment accompanied by carbide precipitation10.1016/j.actamat.2014.11.049 ↗
31. Isothermal transformations in advanced high strength steels below martensite start temperature10.1179/1743284714Y.0000000719 ↗
32. On various aspects of decomposition of austenite in a high-silicon steel during quenching and partitioning10.1007/s11661-013-2053-8 ↗
33. Observation of an isothermal transformation during quenching and partitioning processing10.1007/s11661-009-9891-4 ↗
34. Austenite stabilization and precipitation of carbides during quenching and partitioning (Q&P) of low-alloyed Si–Mn steels with different carbon content10.1016/j.msea.2024.146212 ↗
35. Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: the significant impact on mechanical properties10.1016/j.msea.2019.04.099 ↗
36. A combined 3D-atomic/nanoscale comprehension and ab initio computation of iron carbide structures tailored in Q&P steels via Si alloying10.1039/D3NR00816A ↗
37. Bainitic transformation during the two-step quenching and partitioning process in a medium carbon steel containing silicon10.1016/j.msea.2010.06.045 ↗
38. In-situ EBSD study of deformation behavior of retained austenite in a low-carbon quenching and partitioning steel via uniaxial tensile tests10.1016/j.matchar.2016.06.020 ↗
39. The fracture toughness of TRIP-assisted multiphase steels10.1016/j.actamat.2008.04.035 ↗