Subsurface microstructure versus surface topography: Impact on the fatigue strength of stress-relieved Laser Powder Bed Fusion (L-PBF) 316L parts
Source abstract
Abstract
The Laser Powder Bed Fusion (L-PBF) process allows to manufacture parts with both a complex geometry and a high mechanical performance. The as-built and net-shape L-PBF 316L stainless steel parts - i.e. without any heat nor surface treatment, have tensile residual stresses, subsurface pores, a rough surface and a contourcore microstructure that synergistically lead to a low fatigue strength. Residual stresses can be relieved with a heat-treatment to enhance the fatigue properties, but the best performance is obtained after machining and polishing. The differences between the polished and the heat-treated net-shape conditions lie in the subsurface microstructure, the surface topography, and the population of subsurface pores. This study aims to quantify the impact of each of these subsurface parameters on the fatigue behaviour. To do so, the subsurface microstructure of the net-shape condition is characterised. Then, uni-axial fatigue tests are carried out on stress-relieved specimens with the following surface conditions: net-shape, partially polished, and ‘‘machined and polished’’. The Kitagawa-Takahashi representation shows that for defects smaller than 200 μm, the subsurface microstructure is the most influential parameter on the fatigue strength. Conversely, the surface topography has a limited influence. After examining the microstructure surrounding killer defects of both netshape and polished specimens, the grain size under the surface of all surface conditions is considered in the Kitagawa-Takahashi diagram relatively to the killer defect size: this allows to align the various batches’ results.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Advanced machining processes and optimization · Cellular and Composite Structures
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. A competition between the contour and hatching zones on the high cycle fatigue behaviour of a 316L stainless steel: Analyzed using X-ray computed tomography10.1016/j.msea.2019.04.101 ↗
2. Observations on the influence of process and corrosion related defects on the fatigue strength of 316L stainless steel manufactured by Laser Powder Bed Fusion (L-PBF)10.1016/j.ijfatigue.2021.106552 ↗
3. Rapid method for comparative studies on stress relief heat treatment of additively manufactured 316L10.1016/j.msea.2022.143313 ↗
4. Effects of heat treatment on residual stresses in the laser powder bed fusion of 316L stainless steel: Finite element predictions and neutron diffraction measurements10.1016/j.jmapro.2020.07.023 ↗
5. Fatigue behavior of additively manufactured 316L stainless steel: Competition between the effects of defects and microstructure10.1016/j.ijfatigue.2024.108658 ↗
6. Andreau · 2019
7. Effect of laser-scan strategy on microstructure and fatigue properties of 316L additively manufactured stainless steel10.1111/ffe.13845 ↗
8. Liang · 2020
9. High cycle fatigue behavior of 316L steel fabricated by laser powder bed fusion: Effects of surface defect and loading mode10.1016/j.ijfatigue.2022.106843 ↗
10. Corrosion and microstructural investigation on additively manufactured 316L stainless steel: Experimental and statistical approach10.3390/ma15041605 ↗
11. Size effect due to contour laser scanning in 316L stainless steel produced by laser powder bed fusion10.1016/j.jmrt.2021.11.034 ↗
12. Fatigue strength of 316 L stainless steel manufactured by selective laser melting10.1007/s11665-020-04859-x ↗
13. Investigation of porosity, texture, and deformation behavior using high energy X-rays during in-situ tensile loading in additively manufactured 316L stainless steel10.1016/j.msea.2021.141034 ↗
14. Prevailing effect of residual stresses and defects on the fatigue strength of net-shape parts produced with laser powder bed fusion (L-PBF) 316L stainless steel10.1016/j.ijfatigue.2025.109107 ↗
15. On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting10.1016/j.engfracmech.2014.03.008 ↗
16. Residual stress measurements on AISI 316L samples manufactured by selective laser melting10.1016/j.addma.2017.07.007 ↗
17. Fatigue strength and life assessment of L-PBF 316L stainless steel showing process and corrosion related defects10.1016/j.engfracmech.2022.108883 ↗
18. Roirand · 2023
19. Fatigue strength of PBF-LB/M and wrought 316L stainless steel: Effect of post-treatment and cyclic mean stress10.1111/ffe.13552 ↗
20. Effects of manufacturing parameters and mechanical post-processing on stainless steel 316L processed by laser powder bed fusion10.1016/j.msea.2020.140660 ↗
21. Influences of horizontal and vertical build orientations and post-fabrication processes on the fatigue behavior of stainless steel 316L produced by selective laser melting10.3390/ma12244203 ↗
22. The effect of post-processing heat treatment on the microstructure, residual stress and mechanical properties of selective laser melted 316L stainless steel10.1016/j.msea.2021.141611 ↗
23. New insights on cellular structures strengthening mechanisms and thermal stability of an austenitic stainless steel fabricated by laser powder-bed-fusion10.1016/j.actamat.2020.11.018 ↗
24. Mechanical behavior of additive manufactured, powder-bed laser-fused materials10.1016/j.msea.2015.10.068 ↗
25. High-cycle fatigue behavior of austenitic steel and pure copper under uniaxial, proportional and non-proportional loading10.5545/sv-jme.2013.1600 ↗
26. Effect of re-lasing on the fatigue properties of 316L stainless steel produced by laser powder bed fusion10.1016/j.prostr.2024.03.011 ↗
27. Effect of post-treatments on the fatigue behaviour of 316L stainless steel manufactured by laser powder bed fusion10.1016/j.ijfatigue.2019.01.013 ↗
28. Enhancement and underlying fatigue mechanisms of laser powder bed fusion additive-manufactured 316L stainless steel10.1016/j.msea.2023.145021 ↗
29. Effect of density and surface quality on fatigue behavior of LPBF 316L steel10.1007/978-3-031-32927-2_22 ↗
30. Fatigue behavior of additive manufactured 316L stainless steel parts: Effects of layer orientation and surface roughness10.1016/j.addma.2019.04.011 ↗
31. Applicability of fracture mechanics to very small cracks or the cracks in the early stage
32. Towards the optimization of post-laser powder bed fusion stress-relieve treatments of stainless steel 316L10.1007/s11661-021-06472-6 ↗
33. Determination of the influence of a stress-relief heat treatment and additively manufactured surface on the fatigue behavior of selectively laser melted AISI 316L by using efficient short-time procedures10.1016/j.ijfatigue.2019.105301 ↗
34. Superior low cycle fatigue property from cell structures in additively manufactured 316L stainless steel10.1016/j.jmst.2021.10.006 ↗
35. Influence of laser power and scanning strategy on residual stress distribution in additively manufactured 316L steel10.1016/j.optlastec.2020.106477 ↗
36. Comparative study of additively manufactured and reference 316 L stainless steel samples – Effect of severe shot peening on microstructure and residual stresses10.1016/j.matchar.2022.112162 ↗
37. Comparison of machining performance of stainless steel 316L produced by selective laser melting and electron beam melting10.1016/j.procir.2022.10.052 ↗
38. Separation of the formation mechanisms of residual stresses in LPBF 316L10.3390/met10091234 ↗
39. Microstructural analysis and fatigue crack initiation modelling of additively manufactured 316L after different heat treatments10.1016/j.matdes.2020.108962 ↗
40. Fatigue behavior of additive manufactured 316L stainless steel under axial versus rotating-bending loading: Synergistic effects of stress gradient, surface roughness, and volumetric defects10.1016/j.ijfatigue.2020.106063 ↗
41. Standard practice for determining average grain size using electron backscatter diffraction (EBSD) in fully recrystallized polycrystalline materials, https://www.astm.org/e2627-13r19.html.
42. Strength properties of 316L and 17-4 PH stainless steel produced with additive manufacturing10.3390/ma15186278 ↗
43. Maxwell · 1999
44. 2 - Stress concentration10.1016/B978-0-12-813876-2.00002-9 ↗
45. Surface, microstructure, and tensile deformation characterization of LPBF SS316L microstruts micromachined with femtosecond laser10.1016/j.matdes.2021.110045 ↗
46. Study on mechanism of structure angle on microstructure and properties of SLM-fabricated 316L stainless steel10.3389/fbioe.2021.778332 ↗
47. Processing a non-weldable nickel-base superalloy by selective laser melting: Role of the shape and size of the melt pools on solidification cracking10.1016/j.mtla.2020.100686 ↗
48. Feature-based volumetric defect classification in metal additive manufacturing10.1038/s41467-022-34122-x ↗
49. Bootstrap confidence intervals10.1214/ss/1032280214 ↗
50. Interaction between a surface defect and grain size under high cycle fatigue loading: Experimental approach for armco iron10.1016/j.ijfatigue.2016.01.013 ↗
51. Influence of the position and size of various deterministic defects on the high cycle fatigue resistance of a 316L steel manufactured by laser powder bed fusion10.1016/j.ijfatigue.2020.105930 ↗
52. Beneficial effect of prestrain due to cold extrusion on the multiaxial fatigue strength of a 27MnCr5 steel10.1016/j.ijfatigue.2016.07.012 ↗
53. Artificial defects in 316L stainless steel produced by laser powder bed fusion: Printability, microstructure, and effects on the very-high-cycle fatigue behavior10.1002/adem.202200831 ↗
54. On the Hall-Petch relationship in type 316L stainless steel at room temperature10.1016/0956-716X(90)90545-R ↗
55. Microstructural crack tip plasticity controlling small fatigue crack growth10.1007/978-981-16-7715-1_10 ↗