Energy- and material-efficient Ti-6Al-4V sheet part fabrication by the novel TISTRAQ-process, including resistance heating and tool-based quenching: Insights into test stand design and material potential
Source abstract
Abstract
Sustainable and lightweight manufacturing processes are essential for reducing greenhouse gas emissions and conserving resources. The novel TISTRAQ-process combines a two-stage, short-time heat treatment with an advanced heating and non-isothermal hot forming strategy, thereby ensuring high material and energy efficiency. In this work, a simplified laboratory-scale test stand was developed, enabling direct electric resistance heating and subsequent tool-based quenching of Ti-6Al-4V sheet strips under near-process conditions, but without the complexity of simultaneous forming. The setup allows systematic variation of key process parameters with minimal material consumption, an approach applied in this study to investigate their influence on material properties. Finite element simulations supported the test stand design and provided a valuable understanding of temperature inhomogeneities and their relevance for microstructural evolution and process control. The paper provides detailed insights into (i) the design and capabilities of the test stand, (ii) simulation-based evaluation of temperature homogeneity, (iii) the TISTRAQ process route -including resistance heating, tool-based quenching, and additional short-time annealing, (iv) the resulting microstructural and mechanical properties, and (v) the material response to critical parameters. Experimental results confirm the high potential of the TISTRAQ process to enhance the tensile strength of Ti-6Al-4V. The solution heat treatment temperature and time delay prior to quenching were identified as critical parameters due to their strong influence on microstructure and mechanical behavior. Overall, the study demonstrates how tailored process control can unlock the material potential of Ti-6Al-4V. It also indicates a good scalability of the TISTRAQ-process for lightweight, resource-efficient production of next-generation titanium alloy sheet parts.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Study of the dynamic bauschinger effect in Ti6Al4V by torsion experiments10.1051/epjconf/20122601023 ↗
2. Lütjering · 2007
3. Forming of high strength titanium sheet at room temperature10.1016/j.matdes.2014.03.008 ↗
4. Hoffmann · 2012
5. Sheet metal forming at elevated temperatures10.1016/j.cirp.2006.10.008 ↗
6. Mechanical and microstructural evaluations of hot formed titanium sheets by electrical resistance heating process10.1016/j.msea.2013.04.079 ↗
7. A review of super plastic forming10.1016/j.matpr.2017.12.014 ↗
8. A review on superplastic forming of Ti-6Al-4V and other titanium alloys, mater
9. Odenberger · 2009
10. Formability and microstructure evolution mechanisms of Ti6Al4V alloy during a novel hot stamping process10.1016/j.msea.2018.02.038 ↗
11. Development of Ti–6Al–4V sheet with low temperature superplastic properties10.1016/S0924-0136(01)01037-8 ↗
12. On the mechanistic basis of deformation at the microscale in hexagonal close-packed metals
13. A unified model to predict the hot stamping and subsequent stress-relaxation process of a Ti-6Al-4V alloy10.1088/1757-899X/1270/1/012098 ↗
14. Springback evaluation in hot v-bending of Ti-6Al-4V alloy sheets10.1007/s00170-014-6190-z ↗
15. Thermo-mechanical material response and hot sheet metal forming of Ti-624210.1016/j.msea.2007.12.047 ↗
16. Characterisation of the interfacial heat transfer coefficient in hot stamping of titanium alloys10.1016/j.icheatmasstransfer.2020.104535 ↗
17. Hot stamping of titanium alloy sheet using resistance heating
18. Assessment of electrical resistance heating for hot formability of Ti-6Al-4V alloy sheet10.4028/www.scientific.net/KEM.473.130 ↗
19. Application of electric resistance heating method on titanium hot forming at industrial scale10.1007/s13369-016-2159-6 ↗
20. Strength enhancement of AlMg sheet metal parts by rapid heating and subsequent cold die stamping of severely cold-rolled blanks10.1016/j.msea.2021.142312 ↗
21. Investigation on inductive heating of sheet metal for an industrial hot stamping process
22. Marten · 2017
23. Enhancing mechanical strength of Ti-6Al-4V sheet material by short-time sub-β-transus solution heat treatment and additional short-time annealing
24. Factors determining room temperature mechanical properties of bimodal microstructures in Ti-6Al-4V alloy10.1016/j.msea.2018.06.019 ↗
25. Deformation mechanism of bimodal microstructure in Ti-6Al-4V alloy: the effects of intercritical annealing temperature and constituent hardness10.1016/j.jmst.2020.08.057 ↗
26. A strategy to improve the work-hardening behavior of Ti–6Al–4V parts produced by additive manufacturing10.1080/21663831.2016.1245681 ↗
27. Crystallography and reorientation mechanism upon deformation in the martensite of an α-α’ Ti-6Al-4V dual-phase microstructure exhibiting high work-hardening rate10.1016/j.actamat.2020.116530 ↗
28. Martensite crystal lattice, mechanism of austenite-martensite transformation and behavior of carbon atoms in martensite10.1007/BF02644066 ↗
29. Über den Zusammenhang zwischen dem Kohlenstoffgehalt in Stählen und der Härte des Martensits10.1002/mawe.200390022 ↗
30. On tetragonality of the martensite crystal lattice in steels10.1007/s11661-018-4999-z ↗
31. Fopiano · 1968
32. Strengthening of Ti-6Al-4V alloy by short-time duplex heat treatment10.2320/matertrans.46.1681 ↗
33. Effects of short-time duplex heat treatment on microstructure and fatigue strength of Ti-6Al-4V alloy
34. Exploring the strength-ductility space of Ti-6Al-4V through a quenching and partitioning approach10.1016/j.msea.2025.147859 ↗
35. ANSYS: LS-DYNA Keyword User's Manual R15.0: Volume vol. I, (2024). https://lsdyna.ansys.com/manuals/(accessed April 15, 2025).
36. The new TISTRAQ process: solution treatment with rapid quenching and annealing for Ti-6Al-4V sheet metal part forming-investigation on heat transfer coefficient and influence on cooling rates
37. The new TISTRAQ process: solution treatment with rapid quenching and annealing for Ti-6Al-4V sheet metal part forming-the effect of processing parameters on microstructure and mechanical properties
38. 2013
39. A
40. A direct resistance heating method for shaped blank10.1016/j.jmapro.2020.12.056 ↗
41. Blanking immediately after heating and ultrasonic cleaning for compact hot-stamping systems using rapid resistance heating10.1007/s00170-018-2232-2 ↗
42. Hot stamping of titanium alloy sheets into U shape with concave bottom and joggle using resistance heating10.4028/www.scientific.net/KEM.716.915 ↗
43. Untersuchung energieeffizienter und serientauglicher Erwärmungsstrategien mittels resistiver Erwärmung für den Prässhärteprozess
44. Zwicker · 2014
45. Martensite formation in titanium alloys: crystallographic and compositional effects10.1016/j.jallcom.2021.159636 ↗
46. Phase transformations in the Ti-V system under high pressure up to 25 GPa10.1016/0001-6160(81)90071-7 ↗
47. Fiji: an open-source platform for biological-image analysis10.1038/nmeth.2019 ↗
48. Trainable weka segmentation: a machine learning tool for microscopy pixel classification10.1093/bioinformatics/btx180 ↗