journal article·2022-05Open access

Creep deformation phenomena in near-surface carburised layers of 316H stainless steels

J. Eaton-Mckay, K. Yan, M.D. Callaghan, E. Jimenez-Melero

Abstract

The local creep-induced phenomena occurring within the near-surface carburised layer in two pre-carburised type 316H austenitic stainless steels, containing 0.98 or 1.52 wt% Mn, was assessed at 550 °C. The pre-carburisation exposed both steel grades at either 550 °C (8000 h) or 600 °C (3000 h) to simulated CO2-rich gas environment of UK Advanced Gas-cooled Reactors. The local properties within the carburised layer causes a reduction in minimum creep rate as compared to the non-carburised condition. In both steels carburised at 600 °C, ferrite is observed to form in the most heavily carburised regions, including slip bands, during the initial plastic deformation to the target applied stress. The ferrite area fraction further increases with creep strain. Within the ferritic areas, new fine grains are observed in the creep tested specimens and the fraction of high angle grain boundaries is >60%. Those fine grains have a lower degree of lattice strain compared to the surrounding ferrite area and especially to the austenite matrix. The lattice strain localises within the carburised layer, and the formation of ferrite from the strained austenite, and potentially a dynamic recrystallization within the ferrite regions, pinpoints to a dominant strain relief-driven mechanism. Lattice strain localises primarily in the pre-carburised austenite grains and its carbide-decorated boundaries, and induces the continuous formation and refinement of ferrite grains, and the development of intergranular cracks that evolve further into the bulk structure. These results emphasise the necessity to account for environmental-creep interactions at elevated temperatures in structural assessment procedures, in the current gas-cooled fission reactor fleet and beyond into (very) high-temperature Gen IV and advanced modular reactor designs.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Bhadeshia · 2006
2. Chevalier · 2015
3. Chevalier · 2018
4. Dean · 2015
5. The multiaxial and uniaxial creep ductility of Type 304 steel as a function of stress and strain rate10.1179/mht.2004.007 ↗
6. Abe · 2008
7. Kassner · 2015
8. Hyde · 2013
9. A comprising steady-state creep model for the austenitic AISI 316 L(N) steel10.1016/j.jnucmat.2007.03.062 ↗
10. Creep modelling of 316H stainless steel over a wide range of stress10.1016/j.prostr.2016.06.119 ↗
11. Creep and rupture in Type 316 stainless steel at temperatures between 525 and 900°C Part I: creep rate10.1179/msc.1978.12.11.525 ↗
12. Creep and rupture in Type 316 stainless steel at temperatures between 525 and 900°C Part II: rupture and ductility10.1179/msc.1978.12.11.532 ↗
13. Precipitation in AISI 316L(N) during creep tests at 550 and 600°C up to 10 years10.1016/j.jnucmat.2006.12.027 ↗
14. Creep and rupture in Type 316 stainless steel at temperatures between 525 and 900°C Part III: precipitation behaviour10.1179/msc.1978.12.11.542 ↗
15. A review of precipitation behaviour in AISI type 316 stainless steel10.1016/0025-5416(83)90191-X ↗
16. Microstructure and intergranular corrosion of the austenitic stainless steel 1.497010.1016/j.jnucmat.2006.06.010 ↗
17. Factors influencing long-term creep of type 316 steel at 600°C10.1179/mst.1986.2.11.1123 ↗
18. Characterization of the cavity nucleation factor for life prediction under creep-fatigue interaction10.1007/BF00355887 ↗
19. Improvement of creep-fatigue life by the modification of carbide characteristics through grain boundary serration in an AISI 304 stainless steel10.1023/A:1022989002179 ↗
20. The role of ferrite in Type 316H austenitic stainless steels on the susceptibility to creep cavitation10.1016/j.msea.2015.03.048 ↗
21. Precipitation within localised chromium-enriched regions in a Type 316H austenitic stainless steel10.1007/s10853-017-1748-4 ↗
22. The role of grain boundary ferrite evolution and thermal aging on creep cavitation of type 316H austenitic stainless steel10.1016/j.msea.2021.140859 ↗
23. Nasser · 2016
24. Oxidation and carburization behaviour of two type 316H stainless steel casts in simulated AGR gas environment at 550 and 600 °C10.1016/j.jnucmat.2021.152999 ↗
25. Creep performance of carburized 316H stainless steel at 550 °C10.1016/j.jnucmat.2021.153329 ↗
26. Quantitative metallography by electron backscattered diffraction10.1046/j.1365-2818.1999.00578.x ↗
27. Review Grain and subgrain characterisation by electron backscatter diffraction10.1023/A:1017973432592 ↗
28. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
29. Sequential activation of deformation modes in textured alloy AZ31B during tensile deformation10.1016/j.msea.2020.138921 ↗
30. Microstructure and texture of a lightly deformed TRIP-assisted steel characterized by means of the EBSD technique10.1016/j.msea.2006.10.023 ↗
31. Strain mapping near a triple junction in strained Ni-based alloy using EBSD and biaxial nanogauges10.1016/j.actamat.2011.01.051 ↗
32. In-situ EBSD study of deformation behavior of retained austenite in a low-carbon quenching and partitioning steel via uniaxial tensile tests10.1016/j.matchar.2016.06.020 ↗
33. Quantification of plastic strain of stainless steel and nickel alloy by electron backscatter diffraction10.1016/j.actamat.2005.08.046 ↗
34. High-resolution elastic strain measurement from electron backscatter diffraction patterns: new levels of sensitivity10.1016/j.ultramic.2005.10.001 ↗
35. Gaseous nitriding behaviour of 33CrMoV12-9 steel: evolution of the grain boundaries precipitation and influence on residual stress development10.1016/j.surfcoat.2018.01.068 ↗
36. Chen · 2015
37. Fundamentals of ferrite formation in steels
38. Anomalous creep behaviour of 316 stainless steel at 550°C10.1080/02619180.1986.11753312 ↗
39. Mechanisms of strain accumulation and damage development during creep of prestrained 316 stainless steels10.1007/s11661-004-0367-2 ↗
40. Flannagan · 2015
41. Current issues in recrystallization: a review10.1016/S0921-5093(97)00424-3 ↗
42. Effect of grain size on creep rate in type 316 stainless steel at 873 and 973 K10.1179/030634583790427595 ↗