journal article·2024-06Open access

Controlling splat boundary network evolution towards the development of strong and ductile cold sprayed refractory metals: The role of powder characteristics

Mahsa Amiri, Kliah N. Soto Leytan, Diran Apelian, Daniel R. Mumm, Lorenzo Valdevit

Abstract

Feedstock powder characteristics such as composition (specific alloying elements and concentrations and impurity levels), microstructure, thickness/composition of surface oxide layers, and particle size distribution play a crucial role in determining the overall mechanical properties of cold sprayed deposits. Herein, we report on two deposits consolidated via cold spray processing from differently-sourced batches of nominally identical elemental refractory powders under identical spraying conditions, which exhibit bending strength and ductility values that differ by more than a factor of two – and with the weakest sample displaying negligible effective ductility. Through chemical, microstructural and micromechanical characterization of both the feedstock powders and cold sprayed deposits, we consider the possible influences of feedstock characteristics on the mechanical performance of cold spray consolidated deposits. It is shown that while differences in interstitial oxygen and hydrogen content may result in differences in the intrinsic yield characteristics of the feedstock material, both feedstocks maintain the ductile behavior required to induce good metallurgical bonding upon impact of optimally sized powder particles. We conclude that the deposits formed from the two feedstock powders are indistinguishable and exhibit high ductility when characterized locally within the relatively undeformed bulk of a single particle or splat. However, the two sprayed deposits show extremely low ductility or brittle behavior when loaded in tension across intersplat boundary domains comprising material that has undergone extensive deformation. In addition, one feedstock incorporates a broader particle size distribution, with a long tail of larger-than-optimal particles. These larger particles are accelerated below the critical impact velocity, resulting in observed imperfect metallurgical bonding at splat interfaces and higher porosity at such intersplat boundaries. This result, combined with the overall differences in the morphology of the intersplat boundary network between the two deposits, explains the difference in macroscopic mechanical behavior. We conclude that accurate control of the powder feedstock particle size distribution is essential for optimizing the mechanical integrity of cold sprayed refractory elements and alloys.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Cold spray coating: review of material systems and future perspectives10.1179/1743294414Y.0000000270 ↗
2. From particle acceleration to impact and bonding in cold spraying10.1007/s11666-009-9357-7 ↗
3. Review on cold spray process and technology: Part I - intellectual property10.1007/s11666-008-9203-3 ↗
4. Cold spray: over 30 Years of development toward a hot future10.1007/s11666-022-01366-4 ↗
5. Quantitative percussion diagnostics for evaluating porosity and surface roughness of cold sprayed and laser deposited materials10.1016/j.jmrt.2021.06.047 ↗
6. Surface oxide and hydroxide effects on aluminum microparticle impact bonding10.1016/j.actamat.2020.07.011 ↗
7. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗
8. Development of a generalized parameter window for cold spray deposition10.1016/j.actamat.2005.10.005 ↗
9. Factors governing static properties and fatigue, fatigue crack growth, and fracture mechanisms in cold spray alloys and coatings/repairs: a review
10. Cold spray deposition: significance of particle impact phenomena10.1016/j.ast.2005.03.005 ↗
11. Cold spray deposition of nanocrystalline aluminum alloys10.1007/s11661-005-0182-4 ↗
12. Influence of powder microstructure on the microstructural evolution of as-sprayed and heat treated cold-sprayed Ti-6Al-4V coatings10.1007/s11666-018-0812-1 ↗
13. Comparison of the mechanical and electrochemical properties of WC-17 and 12Co coatings onto Al7075-T6 obtained by high velocity oxy-fuel and cold gas spraying10.1016/j.surfcoat.2014.04.034 ↗
14. Influence of feedstock powder and cold spray processing parameters on microstructure and mechanical properties of Ti-6Al-4V cold spray depositions10.1016/j.surfcoat.2017.12.014 ↗
15. Study of Ti deposition onto Al alloy by cold gas spraying10.1016/j.surfcoat.2010.03.061 ↗
16. Effect of standoff distance on coating deposition characteristics in cold spraying10.1016/j.matdes.2007.02.005 ↗
17. Elimination of porosity in directly fabricated titanium via cold gas dynamic spraying10.1016/j.jmatprotec.2008.03.005 ↗
18. Production of titanium deposits by cold-gas dynamic spray: numerical modeling and experimental characterization10.1361/105996306X108219 ↗
19. Effect of particle morphology and size distribution on cold-sprayed pure titanium coatings10.1007/s11666-013-9951-6 ↗
20. Effect of processing conditions on porosity formation in cold gas dynamic spraying of copper10.1361/105996306X124437 ↗
21. Influence of feedstock powder on microstructure and mechanical properties of Ta cold spray depositions10.1016/j.surfcoat.2019.124903 ↗
22. Significant influence of particle surface oxidation on deposition efficiency, interface microstructure and adhesive strength of cold-sprayed copper coatings10.1016/j.apsusc.2010.03.008 ↗
23. The influence of process parameters and heat treatment on the properties of cold sprayed silver coatings10.1016/j.surfcoat.2011.04.063 ↗
24. Effects of working gas on wear and corrosion resistances of cold sprayed Ti-6Al-4V coatings10.1016/j.surfcoat.2016.05.052 ↗
25. Cold sprayed refractory metals for chrome reduction in gun barrel liners10.1016/j.ijrmhm.2015.07.007 ↗
26. Correlation of splat state with deposition characteristics of cold sprayed niobium coatings10.1016/j.actamat.2017.03.023 ↗
27. Superconducting niobium coating deposited using cold spray10.1016/j.matlet.2022.131715 ↗
28. Tungsten/copper composite deposits produced by a cold spray10.1016/j.scriptamat.2003.08.023 ↗
29. Cold-sprayed copper and tantalum coatings — detailed FESEM and TEM analysis10.1016/j.surfcoat.2010.01.001 ↗
30. Analysis of copper-tungsten cold spray coating: kinetics of coating formation and its thermal properties10.1016/j.surfcoat.2020.125376 ↗
31. The use of Al-Al2O3 cold spray coatings to improve the surface properties of magnesium alloys10.1016/j.surfcoat.2009.07.032 ↗
32. Structural repair using cold spray technology for enhanced sustainability of high value assets10.1016/j.promfg.2018.02.132 ↗
33. Three-dimensional modeling of cold spray for additive manufacturing10.1007/s11666-019-00928-3 ↗
34. Cold spray additive manufacturing and repair: fundamentals and applications
35. Depth-sensing indentation for assessing the mechanical properties of cold-sprayed Ta10.1016/j.surfcoat.2010.08.146 ↗
36. Multi-scale elastic behavior of cold sprayed refractory metal from splat to bulk deposit by integrated experimental and modeling approach10.1016/j.msea.2022.143751 ↗
37. Ta and Ti anti-passivation interlayers for oxygen-evolving anodes produced by cold gas spray10.1007/s11666-015-0219-1 ↗
38. Effect of heat treatment on mechanical properties and corrosion performance of cold-sprayed tantalum coatings10.1007/s11666-016-0388-6 ↗
39. Tantalum based high-pressure cold spray coatings on stainless steel substrate10.4028/www.scientific.net/KEM.813.429 ↗
40. Corrosion properties of cold-sprayed tantalum coatings10.1007/s11666-008-9281-2 ↗
41. Analysis of tantalum coatings produced by the kinetic spray process10.1361/10599630419418 ↗
42. Influence of coating defects on the corrosion behavior of cold sprayed refractory metals10.1016/j.apsusc.2016.11.022 ↗
43. Characteristics of kinetic sprayed Ta in terms of the deposition behavior, microstructural evolution and mechanical properties: effect of strain-rate-dependent response of Ta at high temperature10.1016/j.matchar.2018.04.023 ↗
44. The elastic modulus of cold spray coatings: influence of inter-splat boundary cracking10.1007/s11666-013-0034-5 ↗
45. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
46. Microstructure, deformation and cracking characteristics of thermal spray ferrous coatings10.1016/S0921-5093(99)00132-X ↗
47. A methodology to investigate size scale effects in crystalline plasticity using uniaxial compression testing10.1016/j.msea.2005.03.082 ↗
48. Amorphous complexions alter the tensile failure of nanocrystalline Cu-Zr alloys10.1016/j.mtla.2021.101134 ↗
49. The design of accurate micro-compression experiments10.1016/j.scriptamat.2005.06.043 ↗
50. Relation between hydrogen embrittlement and the formation of hydride in the group V transition metals10.1007/BF02642552 ↗
51. The effects of interstitials and hydrogen-interstitial interactions on low temperature hardening and embrittlement in V, Nb, and Ta10.1007/BF02665317 ↗
52. Effect of the nitrogen-to-hydrogen ratio on the mechanical behavior of vanadium, niobium and tantalum10.1016/0025-5416(87)90287-4 ↗
53. Plastic deformation of tantalum single crystals: II. The orientation dependence of yield10.1016/0022-5088(68)90115-X ↗
54. Uniaxial compression of single crystal and polycrystalline tantalum10.1016/j.msea.2019.05.006 ↗
55. Low energy cleavage fracture associated with the hydrogen embrittlement of refractory metal alloys10.1016/0921-5093(89)90322-5 ↗
56. Synchrotron X-ray diffraction studies of the phase-specific deformation in additively manufactured Ni–CrC composites10.1016/j.compositesb.2021.109086 ↗
57. A review of the mechanical and tribological behavior of cold spray metal matrix composites10.1007/s11666-020-01091-w ↗
58. Branch · 2020
59. In-situ mechanical investigation of the deformation of splat interfaces in cold-sprayed aluminum alloy10.1016/j.msea.2018.09.065 ↗
60. On parameter selection in cold spraying10.1007/s11666-011-9662-9 ↗