journal article·2025-06Open access

Dynamic recrystallization during microindentation: A site-specific study of indents using a novel LaserFIB method

Mina Dehghan, Travis Casagrande, Priti Wanjara, Javad Gholipour, Ahmed A. Tiamiyu

Abstract

Grain-refinement by continuous dynamic recrystallization (cDRX) is generally known to require extreme deformation conditions—high strain/strain rates—like those observed in extreme deformation processes, e.g., microparticle impact and high-energy ball milling. It is not clear whether cDRX steps can be interrupted to circumvent the requirement for such extreme conditions; a phenomenon we term two-step cDRX or interrupted cDRX (icDRX). We hypothesized that simple microindentation of a predeformed metal could result in grain refinement by icDRX mechanism without the need for post-process heat treatment, as conventionally done. Microindention of friction stir processed (FSP) aluminum is conducted to test this hypothesis. To circumvent the limitations involved in the characterization of a large indent size and the problem with conventional focused ion beam (FIB) methods of accessing deep regions of interest such as the apex of an indent, we use a custom FIB lift-out grid and LaserFIB-method to extract a large TEM lamella from microindents for scanning/transmission electron microscopy (S/TEM). The results show an unusually high hardness value for aluminum that is explained by the transformation of prior dislocation cells to bonafide cDRXed ultrafine grains during microindentation to establish an icDRX grain refinement mechanism: prior dislocation cells develop into partitioned elongated subgrains at the upper corner of the indent ; evidence of ultrafine near-equiaxed grains that indicates the onset of cDRX emerges midway down the indent ; and complete grain refinement by icDRX occur at the indent apex . Conclusively, the microstructural observations are also consistent with the deformation map for aluminum, while the hardness/yield strength is reasonably modeled. These findings are particularly interesting for metal additive manufacturing (and allied) processes that develop dislocation cell structures; an additional simple plastic deformation step on these manufactured parts can drive the dislocation cells to completely refined grains by icDRX , thereby improving materials’ mechanical properties.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Microstructure and mechanical properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (92)

Show source-provided references
1. Chapter 7-recrystallization of single-phase alloys
2. Review on modeling and simulation of dynamic recrystallization of martensitic stainless steels during bulk hot deformation10.1016/j.jmrt.2022.03.179 ↗
3. Effect of grain size on grain boundary strengthening of copper bicrystals under cyclic loading10.1179/026708300101507640 ↗
4. Dynamic recrystallization in lead10.1007/BF03037889 ↗
5. Geometric dynamic recrystallization in hot torsion of Al 5Mg 0.6 Mn (AA5083)10.1016/0921-5093(95)09990-5 ↗
6. Nanotwinning-assisted dynamic recrystallization at high strains and strain rates10.1038/s41563-022-01250-0 ↗
7. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
8. Humphreys · 2012
9. Modeling of continuous dynamic recrystallization in commercial-purity aluminum10.1016/j.msea.2009.09.043 ↗
10. Effect of pass strain on grain refinement in 7475 Al alloy during hot multidirectional forging10.2320/matertrans.45.2232 ↗
11. Modelling continuous dynamic recrystallization of aluminum alloys based on the polycrystal plasticity approach10.1016/j.ijplas.2020.102710 ↗
12. Continuous dynamic recrystallization (CDRX) model for aluminum alloys10.1007/s10853-017-1845-4 ↗
13. Continuous dynamic recrystallization in an Al–Li–Mg–Sc alloy during equal-channel angular extrusion10.1016/j.msea.2005.01.053 ↗
14. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
15. Microstructural evolution of 6061 aluminum gas-atomized powder and high-pressure cold-sprayed deposition10.1007/s11666-013-0049-y ↗
16. Heterogeneous microstructural evolution during hydrodynamic penetration of a high-velocity copper microparticle impacting copper10.1016/j.mattod.2023.11.015 ↗
17. Establishing the microstructure-strengthening correlation in severely deformed surface of titanium10.1080/14786435.2018.1478141 ↗
18. Nanostructure formation mechanism during in-situ consolidation of copper by room-temperature ball milling10.1016/j.matdes.2014.06.052 ↗
19. Texture evolution of an Al-8Zn alloy during ECAP and post-ECAP isothermal annealing10.1016/j.matchar.2019.109794 ↗
20. Effect of equal channel angular pressing (ECAP) on the evolution of texture, microstructure and mechanical properties in the al-cu-li alloy AA219510.1016/j.jallcom.2019.01.161 ↗
21. Microhardness testing of cementitious materials10.1016/S1065-7355(96)90051-6 ↗
22. Indentation fracture: principles and applications10.1007/BF00823224 ↗
23. Standard test methods for micro-hardness of materials (E384)
24. Effect of welding parameters on microstructure and mechanical properties of AA7075‐T6 friction stir welded joints10.1111/j.1460-2695.2011.01580.x ↗
25. Localised surface modification of high-strength aluminium–alumina metal matrix composite coatings using cold spraying and friction stir processing10.1080/17436753.2023.2227446 ↗
26. Review of tools for friction stir welding and processing10.1179/1879139512Y.0000000015 ↗
27. Relationship between grain size and zener–holloman parameter during friction stir processing in AZ31 Mg alloys10.1016/j.scriptamat.2004.05.043 ↗
28. 2007 · 12
29. Standard test methods for determining average grain size
30. NIH image to ImageJ: 25 years of image analysis10.1038/nmeth.2089 ↗
31. Hardness, K. & Machines, T. Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials BT—Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials, vol. iI (17AD), p 1.
32. Laser ablation for site-specific TEM sample preparation in a FIB-SEM
33. Analysis tools for electron and X-ray diffraction
34. An experimental study of the recrystallization mechanism during hot deformation of aluminium10.1016/S0921-5093(00)00733-4 ↗
35. Effect of strain rate upon plastic flow of steel10.1063/1.1707363 ↗
36. High strain rate superplasticity via friction stir processing (FSP): a review10.1016/j.msea.2021.141499 ↗
37. Large strain deformation and ultra-fine grained materials by machining10.1016/j.msea.2005.08.139 ↗
38. Dislocation cell formation in metals10.1063/1.1659399 ↗
39. Effect of the indenter size on the indentation of aluminum10.1016/j.matchar.2006.02.012 ↗
40. Dislocation density and internal stress in an Al-5.7 at% Mg alloy10.2320/matertrans1960.26.423 ↗
41. Plastic deformation at high strain rates10.1002/9780470172278.ch13 ↗
42. Experimental and numerical studies on the behavior of thin aluminum plates subjected to impact by blunt-and hemispherical-nosed projectiles10.1016/j.ijimpeng.2005.06.007 ↗
43. Numerical simulation of deformation behavior of Al particles impacting on Al substrate and effect of surface oxide films on interfacial bonding in cold spraying10.1016/j.apsusc.2006.11.020 ↗
44. Strengthening in Al alloy nano composites fabricated by ultrasound assisted solidification technique10.1016/j.msea.2015.10.118 ↗
45. Microstructural evolution in copper subjected to severe plastic deformation: experiments and analysis10.1016/j.actamat.2006.07.008 ↗
46. Dislocation density-based modeling of deformation behavior of aluminium under equal channel angular pressing10.1016/S0921-5093(02)00847-X ↗
47. Experimental evaluation of strain and strain rate during rapid cooling friction stir welding of pure copper10.1080/13621718.2018.1556436 ↗
48. On material flow in friction stir welded Al alloys10.1016/j.jmatprotec.2016.08.030 ↗
49. Influence of shear banding on the formation of brass-type textures in polycrystalline fcc metals with low stacking fault energy10.1016/j.jmst.2013.11.010 ↗
50. Electron backscatter diffraction and orientation imaging microscopy10.1179/mst.1997.13.1.69 ↗
51. A quantitative evaluation of microstructure by electron back-scattered diffraction pattern quality variations10.1017/S1431927613012397 ↗
52. Deformation-induced long-range internal stresses and lattice plane misorientations and the role of geometrically necessary dislocations10.1080/14786430500509054 ↗
53. The deformation of plastically non-homogeneous materials10.1080/14786437008238426 ↗
54. The microstructural origin of work hardening stages10.1016/j.actamat.2018.02.002 ↗
55. Dislocation boundaries and active slip systems10.1016/0956-7151(95)00097-F ↗
56. Geometrically necessary, incidental and subgrain boundaries10.1016/0956-716X(91)90451-6 ↗
57. Theory of plastic deformation:-properties of low energy dislocation structures10.1016/0921-5093(89)90290-6 ↗
58. Theory of dislocation cell sizes in deformed metals10.1016/0025-5416(82)90086-6 ↗
59. A thermodynamic theory for dislocation cell formation and misorientation in metals10.1016/j.actamat.2012.05.003 ↗
60. Modelling plastic deformation in BCC metals: dynamic recovery and cell formation effects10.1016/j.msea.2012.08.068 ↗
61. Smallman · 2016
62. Deformation-induced point defects in NiAl single crystals10.1016/S0966-9795(99)00045-X ↗
63. Extended expanding cavity model for measurement of flow properties using instrumented spherical indentation10.1016/j.ijplas.2013.02.014 ↗
64. Two new expanding cavity models for indentation deformations of elastic strain-hardening materials10.1016/j.ijsolstr.2005.03.062 ↗
65. An expanding cavity model incorporating strain-hardening and indentation size effects10.1016/j.ijsolstr.2006.01.008 ↗
66. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
67. Tabor · 1985
68. Multiplication processes for slow moving dislocations10.1103/PhysRev.79.722 ↗
69. Investigation of material properties of thin copper films through finite element modelling of microindentation test10.1016/j.apsusc.2008.02.101 ↗
70. Mechanics of plastic flow past a narrow-angle wedge indenter10.1080/14786435.2019.1644462 ↗
71. Crystallographic analysis of nucleation at hardness indentations in high-purity aluminum10.1007/s11661-016-3704-3 ↗
72. Fatigue-damage evaluation in aluminum heat-transfer tubes by measuring dislocation cell-wall thickness10.1016/S0921-5093(01)01156-X ↗
73. Ordinary dislocation configurations in high Nb-containing TiAl alloy deformed at high temperatures10.1080/14786435.2016.1267877 ↗
74. The geometry and nature of pinning points of ½⟨ 110] unit dislocations in binary TiAl alloys10.1080/01418619708200010 ↗
75. Interfacial dislocation networks around γ′ precipitates in nickel-base alloys10.1080/14786437508221665 ↗
76. Direct observation of nucleation in the bulk of an opaque sample
77. Selective growth of recrystallizing grains into well-characterized deformed aluminum at hardness indentation10.1016/j.actamat.2024.119862 ↗
78. Further understanding of metadynamic recrystallization through thermomechanical tests and EBSD characterization10.1016/j.jmatprotec.2021.117359 ↗
79. Experimental measurement of dislocation density in metallic materials: a quantitative comparison between measurements techniques (XRD, R-ECCI, HR-EBSD, TEM)10.1016/j.matchar.2023.112842 ↗
80. Quantitative analysis of dislocation distributions10.1016/0026-0800(70)90010-8 ↗
81. Effect of multi-pass friction stir processing on microstructures and mechanical behaviors of as-cast 2A14 aluminum alloy10.1007/s11665-021-05594-7 ↗
82. Grain size evolution during discontinuous dynamic recrystallization10.1016/j.scriptamat.2013.09.020 ↗
83. Physics and phenomenology of strain hardening: the FCC case10.1016/S0079-6425(02)00003-8 ↗
85. Effect of grain size reduction and geometrical confinement in fine grained copper: potential applications as a material for reversible electrical contacts10.1002/adem.200900346 ↗
86. 1951 · 747
87. The cleavage strength of polycrystals
88. Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L10.1016/j.actamat.2020.07.063 ↗
89. The origin of high-density dislocations in additively manufactured metals10.1080/21663831.2020.1751739 ↗
90. Role of hierarchical microstructure of additively manufactured AlSi10Mg on dynamic loading behavior
91. Dislocation cells in additively manufactured metallic alloys characterized by electron backscatter diffraction pattern sharpness10.1016/j.matchar.2023.112673 ↗
92. Dislocation structures formation induced by thermal stress in additive manufacturing: multiscale crystal plasticity modeling of dislocation transport10.1016/j.jmps.2023.105235 ↗