Development of a novel heat treatment in L-PBF fabricated high strength A205 Al alloy: Impact on microstructure-mechanical properties
Source abstract
Abstract
Recent advances in the additive manufacturing of high-strength aluminium alloys have enabled the replacement of cast components in the aerospace and automotive sectors. However, a major challenge facing additively manufactured alloys is the lack of standardised heat treatments (HT) to optimise mechanical properties. This study investigates the development of a novel Rapid HT and its influence on the microstructure and mechanical properties of the A205 aluminium alloy (A20X™) fabricated by Laser-Powder Bed Fusion (L-PBF). The alloy was subjected to three HTs: Standard T7 HT, Commercial HT, and Rapid HT. Microstructural analysis, using Scanning electron microscopy (SEM) and Electron backscatter diffraction (EBSD), revealed a finer grain size for Commercial HT and Rapid HT, with average grain sizes of 2.4 μm and 2.3 μm, respectively, compared to the average 3.2 μm of the Standard T7. STEM analysis revealed a higher volume fraction and finer Ω-AlCuAgMg and ϑ'-Al 2 Cu precipitates in the Rapid HT compared to the other HTs. Mechanical tests highlighted superior performance for the Rapid HT, achieving a UTS of 465 MPa, compared to the values of 422 MPa and 449 MPa for Standard T7 HT and Commercial HT, respectively. Additionally, the Rapid HT showed an increase in fatigue life of around 189 % and 125 % and in creep life of around 33 % and 80 % compared to Standard T7 HT and Commercial HT, respectively. These findings highlight the novelty of the Rapid HT in refining microstructure and enhancing mechanical properties beyond conventional HTs, paving the way for more efficient and sustainable HT strategies for L-PBF manufactured high-strength Al alloys. • A Rapid Heat Treatment was successfully developed for the L-PBF manufactured A205. • A comparison between, Standard T7 HT, a Commercial HT, and Rapid HT was performed. • Tensile, fatigue and creep tests were performed to compare the studied HTs. • The Rapid HT offered a combination of strength and ductility, compared to other HTs. • Strengthening mechanisms were evaluated to analyse material-properties correlations.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Review of high-strength aluminium alloys for additive manufacturing by laser powder bed fusion10.1016/j.matdes.2022.110779 ↗
2. Additive manufacturing of heat exchangers in aerospace applications: a review10.1016/j.applthermaleng.2023.121387 ↗
3. Challenges in additive manufacturing of high-strength aluminium alloys and current developments in hybrid additive manufacturing10.1016/j.ijlmm.2020.12.004 ↗
4. Additive manufacturing of aluminum alloys for aeronautic applications: advantages and problems10.3390/met13040716 ↗
5. Synchrotron characterisation of ultra-fine grain TiB2/Al-Cu composite fabricated by laser powder bed fusion10.1007/s40195-021-01317-y ↗
6. Fiocchi · 2021 · 204
7. Additive manufacturing: a review of the influence of building orientation and post heat treatment on the mechanical properties of aluminium alloys
8. Heat treatment for metal additive manufacturing10.1016/j.pmatsci.2022.101051 ↗
9. Microstructural-micromechanical correlation in an Al–Cu–Mg–Ag–TiB2 (A205) alloy: additively manufactured and cast10.1016/j.msea.2021.142453 ↗
10. Correlation between tensile properties, microstructure, and processing routes of an Al–Cu–Mg–Ag–TiB2 (A205) alloy: additive manufacturing and casting10.1016/j.msea.2022.142989 ↗
11. The effect of heat treatment on fatigue response of laser powder bed fused Al-Cu-Mg-Ag-TiB2 (A20X) alloy
12. Very high cycle fatigue of laser powder bed fused Al-Cu-Mg-Ag-TiB2 (A20X) Alloy: stress relief and aging treatments10.1016/j.ijfatigue.2024.108281 ↗
13. Ambient-temperature time-dependent deformation of cast and additive manufactured Al-Cu-Mg-Ag-TiB2 (A205)10.1016/j.micron.2022.103246 ↗
14. Creep behavior of additively manufactured high strength A205 aluminum alloy10.1016/j.addlet.2023.100142 ↗
15. Precipitate evolution and thermal stability of A205 fabricated using laser powder bed fusion10.1007/s10853-023-08163-6 ↗
16. Revisiting heat treatments for additive manufactured parts: a case study of A20X alloy10.1016/j.matdes.2022.111566 ↗
17. 2017
18. Natural and artificial aging behaviour of Al-Cu-Mg-Ag-Ti-B (A205) alloy processed by laser powder bed fusion: strengthening mechanisms and failure analysis
19. Heat treating of aluminum and its alloys
20. Aeromet
21. 2017
22. Beausir
23. 2023
24. 2022
25. 2021
26. 2018
27. Processability and characterization of A20X aluminum alloy fabricated by laser powder bed fusion
28. The nano-structural characterization of Ω and S phases in Al-5.1Cu-1.0 Mg-(0.4Ag) AA2024 aluminum alloys10.1016/j.msea.2023.145361 ↗
29. Subtle atomistic processes of S-phase formation in Al-Cu-Mg alloys10.1016/j.jallcom.2020.155677 ↗
30. Precipitation structure and strengthening mechanisms in an Al-Cu-Mg-Ag alloy10.1016/j.msea.2017.06.110 ↗
31. Selective laser melting of AlSi10Mg alloy: process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
32. Insight into the recrystallization behavior and precipitation reaction of in-situ nano TiB2/AlCuMg composite during heat treatment10.1016/j.matchar.2021.111458 ↗
33. In situ detection of thermally induced porosity in additively manufactured and sintered objects10.1007/s10853-019-03452-5 ↗
34. Effects of porosity on the mechanical properties of additively manufactured components: a critical review10.1088/2053-1591/abcc5d ↗
35. Metal powders in additive manufacturing: a review on reusability and recyclability of common titanium, nickel and aluminum alloys
36. Direct aging of additively manufactured A20X aluminum alloy10.1016/j.jallcom.2023.172071 ↗
37. Achieving strength-ductility balance in a laser powder bed fusion fabricated TiB2/Al–Cu-Mg-Ag alloy10.1016/j.jallcom.2023.169311 ↗
38. Aging behavior and strengthening mechanisms of coarsening resistant metastable θ' precipitates in an Al–Cu alloy10.1016/j.matdes.2020.109378 ↗
39. Effect of laser contour scan parameters on fatigue performance of A20X fabricated by laser powder bed fusion10.1016/j.ijfatigue.2023.107775 ↗
40. Comparison of grain size dependence on the creep performance of a Mg–Y alloy along different loading directions10.1016/j.msea.2024.146155 ↗
41. Enhanced creep performance in an Al–Cu–Mg–Ag alloy through underageing10.1016/S1359-6454(02)00164-7 ↗
42. Microstructural consistency in the additive manufactured metallic materials: a study on the laser powder bed fusion of AlSi10Mg
43. Understanding the mechanism of columnar–to-equiaxed transition and grain refinement in additively manufactured steel during laser powder bed fusion
44. Correlation of microstructure to creep response of hot isostatically pressed and aged electron Beam melted inconel 71810.1007/s11661-018-4812-z ↗