Laser-directed energy deposition additive manufacturing of a lean hot work tool steel: Tempering behavior and impact toughness
Source abstract
Abstract
HWTS 50 is a Cr, Mo, V is a new lean hot work tool steel with ∼0.2 wt% carbon, designed with chemical composition modifications to achieve comparable properties and temper resistance to those of medium carbon hot work tool steels such as AISI H13 (∼0.4 % C in wt.), while offering improved processability in laser additive manufacturing (LAM) processes. This paper reports on the processing and properties of this tool steel by laser-directed energy deposition (L-DED). Results suggest achievement of near-fully dense and crack-free martensitic microstructure with up to 6 vol% retained austenite (RA), which is substantially lower than that typically found in laser AM-processed AISI H13 (i.e., up to 20 vol%). As-built (AB) material exhibits a hardness of ∼47 HRC and Charpy V-notch impact energy of ∼20 J. Hardness of 48–50 HRC can be achieved by tempering slightly above the secondary hardness peak of 575 °C, either through quenching and tempering or direct double tempering from AB condition. Direct tempering improves temper resistance due to higher dislocation density and higher matrix supersaturation in elements carbon, nitrogen, and vanadium in AB condition, leading to a higher number density of fine and stable secondary carbides through over-tempering. In the above hardness range, the impact toughness of quenched and tempered steel was substantially higher than that of directly tempered one (i.e., ∼18 J vs. ∼12 J). Increased impact energy by prior quenching could be ascribed to microstructural homogenization, removal of inter-dendritic micro-segregation, and columnar prior austenite grain boundaries, which act as preferential sites for chains of alloy carbides precipitation, serving as low energy preferential crack initiation and propagation path. The new steel grade showed enhanced tempering resistance compared to AISI H13, particularly at elevated temperatures (i.e., >600 °C). Enhanced AM processability, optimum balance of hardness-, impact toughness-, and tempering resistance suggest it can be used for the manufacturing and repair of hot work tool steels in laser AM processes.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. State-of-the-art laser additive manufacturing for hot-work tool steels10.1016/j.procir.2017.03.073 ↗
2. Laser Powder Bed Fusion printability of cobalt-free steel powders for manufacturing injection molds
3. A numerical and experimental investigation of the thermal behavior of a permanent metal mold with a conventional cooling channel and a new cooling channel design10.1007/s40962-021-00633-4 ↗
4. Thermal fatigue life prediction method for die casting mold steel based on the cooling cycle10.1016/j.jmatprotec.2023.118131 ↗
5. Simulation and evaluation of thermal fatigue cracking of hot work tool steels10.1016/j.ijfatigue.2004.03.005 ↗
6. Directed energy deposition (DED) additive manufacturing: physical characteristics, defects, challenges and applications10.1016/j.mattod.2021.03.020 ↗
7. Comparison of softening behavior and abrasive wear resistance between conventionally and additively manufactured tool steels10.1002/srin.202300577 ↗
8. Application of directed energy deposition-based additive manufacturing in repair10.3390/app9163316 ↗
9. Directed energy deposition (DED) process: state of the art10.1007/s40684-020-00302-7 ↗
10. In-situ preheating: novel insights into thermal history and microstructure of directed energy deposition-arc of hot-work tool steels10.1016/j.jmrt.2024.10.098 ↗
11. The effects of deposited layer thickness on the material and geometrical properties of L-DED processed AISI D2 tool steel
12. Microstructure and properties of a novel carbon-martensitic hot work tool steel processed by laser additive manufacturing without preheating10.1002/srin.202200439 ↗
13. Cracking mechanism in a laser powder bed fused cold-work tool steel: the role of residual stresses, microstructure and local elemental concentrations10.1016/j.actamat.2021.117570 ↗
14. Microstructural evolution and martensitic transformation in FeCrV alloy fabricated via additive manufacturing10.1016/j.msea.2021.140943 ↗
15. Solidification and microstructure evolution in additively manufactured H13 steel via directed energy deposition: integrated experimental and computational approach10.1016/j.jmapro.2021.06.009 ↗
16. Experimental study and modeling of H13 steel deposition using laser hot-wire additive manufacturing10.1016/j.jmatprotec.2016.04.006 ↗
17. Characterization of microstructure and residual stress in a 3D H13 tool steel component produced by additive manufacturing10.1557/jmr.2014.190 ↗
18. General investigations on processing tool steel X40CrMoV5-1 with selective laser melting10.1016/j.jmatprotec.2018.01.012 ↗
19. Influence of powder bed preheating on microstructure and mechanical properties of H13 tool steel SLM parts10.1016/j.phpro.2016.08.092 ↗
20. Influence of post treatment on microstructure, porosity and mechanical properties of additive manufactured H13 tool steel10.1016/j.msea.2018.08.046 ↗
21. A study of microstructure and cracking behavior of H13 tool steel produced by laser powder bed fusion using single-tracks, multi-track pads, and 3D cubes10.1016/j.jmatprotec.2020.116802 ↗
22. Influence of Cr3C2 additions to AISI H13 tool steel in the LPBF process10.1002/srin.202100454 ↗
23. Review on field assisted metal additive manufacturing10.1016/j.ijmachtools.2023.104032 ↗
24. Porosity, cracks, and mechanical properties of additively manufactured tooling alloys: a review
25. Combinatorial alloy design by laser additive manufacturing10.1002/srin.201600416 ↗
26. Alloy design and adaptation for additive manufacture10.1016/j.jmatprotec.2021.117358 ↗
27. Design and tailoring of alloys for additive manufacturing10.1007/s11661-020-06009-3 ↗
28. Additive manufacturing of tool steels10.1002/srin.202200372 ↗
29. Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing10.1016/j.jnucmat.2020.152742 ↗
30. Novel high alloying hot-work tool steel with enhanced wear resistance prepared by laser additive manufacturing10.1088/2053-1591/ab49d9 ↗
31. Investigation on microstructure, hardness and fracture energy of AISI H13 hot work tool steel by cyclic heat treatment10.1007/s11665-023-08439-7 ↗
32. Production and characterization of a modified hot work tool steel by laser powder bed fusion10.1007/s11661-022-06694-2 ↗
33. General investigations on the heat treatment and thermal fatigue behavior of an experimental hot work tool steel tailored for laser powder bed fusion10.1016/j.msea.2024.146554 ↗
34. Influence of silicon content on the precipitation of secondary carbides and fatigue properties of a 5%Cr tempered martensitic steel10.1016/j.msea.2004.11.050 ↗
35. Roberts · 1998
36. Tempering of steel10.1007/BF02642436 ↗
37. Feedback control effects on dimensions and defects of H13 tool steel by direct metal deposition process10.2351/1.1848530 ↗
38. Effect of heat treatment on microstructure and mechanical properties of laser additively manufactured AISI H13 tool steel10.1007/s11665-017-2992-0 ↗
39. Mechanical characteristics of a tool steel layer deposited by using direct energy deposition10.1007/s12540-017-6442-1 ↗
40. Effect of different post-processing thermal treatments on the fracture toughness and tempering resistance of additively manufactured H13 hot-work tool steel10.3390/met14010112 ↗
41. Assessment of geometrically necessary dislocation levels derived by 3D EBSD10.1016/j.actamat.2015.06.051 ↗
42. Abnormal martensitic transformation and morphology induced by chemical heterogeneity in additively manufactured maraging steel10.1016/j.scriptamat.2024.116313 ↗
43. Effects of powder atomization route and post-processing thermal treatments on the mechanical properties and fatigue resistance of additively manufactured 18Ni300 maraging steel10.1002/adem.202101011 ↗
44. The morphology and crystallography of lath martensite in Fe-C alloys10.1016/S1359-6454(02)00577-3 ↗
45. Laser powder bed fusion and directed energy deposition of A novel hot work tool steel: a comparative study10.59499/EP246282485 ↗
46. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
47. Stabilisation of retained austenite in laser surface melted tool steels10.1016/j.msea.2004.06.069 ↗
48. Achieving ultrahigh yield strength and decent toughness in an in-situ alloyed H13 steel via laser powder bed fusion
49. Heat treatment and properties of a hot work tool steel fabricated by additive manufacturing10.1016/j.msea.2019.03.027 ↗
50. Description of a new concept for the development of adapted hot-work tool steels for laser-powder bed fusion
51. Tempering behavior of a direct laser deposited hot work tool steel: influence of quenching on secondary hardening and microstructure10.1016/j.msea.2021.141126 ↗
52. Effect of intrinsic heat treatment on the precipitate formation of X40CrMoV5–1 tool steel during laser-directed energy deposition: a coupled study of atom probe tomography and in situ synchrotron X-ray diffraction10.1016/j.actamat.2024.120488 ↗
53. Microstructure evolution during laser-directed energy deposition of tool steel by in situ synchrotron X-ray diffraction
54. Martensite in steel: strength and structure10.1016/S0921-5093(99)00288-9 ↗
55. Bhadeshia
56. Image processing tool quantifying auto-tempered carbides in as-quenched low carbon martensitic steels10.3390/met10020171 ↗
57. Thermal fatigue testing of chromium martensitic hot-work tool steel after different austenitizing treatments10.1016/j.jmatprotec.2004.04.158 ↗
58. On the origin of enhanced tempering resistance of the laser additively manufactured hot work tool steel in the as-built condition
59. Silicon in die steels
60. Kinetics of precipitation in a complex hot-work tool steel10.1002/srin.200900069 ↗
61. Comparative study of the tempering behavior of different martensitic steels by means of in-situ diffractometry and dilatometry10.3390/ma13225058 ↗
62. Tempering of iron-carbon martensite; dilatometric and calorimetric analysis, Metallurgical Transactions
63. Modern prehardened tool steels in die-casting applications10.1080/10426910902841753 ↗
64. Correlation between the KIc, the HRc and the Charpy V-notch test results for H11/H13 hot-work tool steels at room temperature10.1002/srin.200806355 ↗
65. Osprey® HWTS 50 hot-work tool steel metal powder — Metal powder | Sandvik, (n.d.). https://www.metalpowder.sandvik/en/products/metal-powder-alloys/tool-and-high-speed-steel/osprey-hwts-50/(accessed December 7, 2024).
66. Uddeholm Orvar Supreme, (n.d.). https://www.uddeholm.com/sweden/sv/products/uddeholm-orvar-supreme/(accessed December 9, 2024).
67. Post-process heat treatment of tool steel dies repaired by Laser Direct Energy Deposition