Enhancing mechanical strength of Ti-6Al-4V sheet material by short-time sub-β-transus solution heat treatment and additional short-time annealing
Source abstract
Abstract
In the Ti-6Al-4V alloy, bimodal α+α' microstructures characterized by high work-hardening capability and high ductility can be obtained by solution heat treatment just below the β-transus temperature followed by quenching. In literature it is indicated that additional short-time annealing can significantly enhance the material’s strength. Based on these studies, this work aims to understand the influence of short-time solution heat treatment parameters and additional short-time annealing on the mechanical properties of Ti-6Al-4V sheet material, with a goal of evaluating the suitability of short-time heat treatments for implementation in processing techniques for sheet metal parts. A vertical furnace purged with Argon gas was employed to produce various materials states via short-time solution heat treatment and water quenching and additional short-time annealing. The solution heat treatment parameters were systematically varied as follows: (i) solution heat treatment temperature in the range of 875 °C - 955 °C and (ii) solution heat treatment time in the range of 70 s - 540 s. The effects of (i) and (ii) were investigated both without and with an additional short-time annealing at 570 °C for 180 s. Microstructural properties investigated by scanning electron microscopy combined with mechanical properties obtained by tensile and nanoindentation tests allow comprehensive evaluation of the different material conditions. It was observed that the application of an additional short-time annealing to the solution heat treated and quenched material resulted in a pronounced increase in strength, which was attributed to the hardening of the martensitically transformed prior β-grains, while maintaining moderate ductility. The solution heat treatment temperature is the crucial parameter influencing microstructure (e.g. phase fractions, interface characteristics, chemical phase composition) and, consequently, the deformation behavior within the solution heat treatment step. Increasing the solution heat treatment temperature resulted in higher strength and reduced ductility, allowing the mechanical properties to be tailored for specific future technological applications. In contrast, the solution heat treatment time in the range investigated did not have a substantial impact on mechanical properties.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Titanium Alloys Microstructure and Properties · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Titanium alloys for aerospace applications10.1002/adem.200310095 ↗
2. Materials considerations for aerospace applications10.1557/mrs.2015.278 ↗
3. High-efficiency forming processes for complex thin-walled titanium alloys components: state-of-the-art and perspectives10.1088/2631-7990/ab949b ↗
4. Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys10.1016/S0921-5093(97)00778-8 ↗
5. Phase transformations during cooling in α+β titanium alloys10.1016/S0921-5093(97)00802-2 ↗
6. Bi-lamellar microstructure in Ti–6Al–4V: microstructure evolution and mechanical properties10.1016/j.msea.2019.138077 ↗
7. Influence of thermal treatment on element partitioning in α+β titanium alloy10.1016/j.jallcom.2019.03.332 ↗
8. Effects of heating rate on the alloy element partitioning and mechanical properties in equiaxed α+β Ti-6Al-4V alloy10.1016/j.jmst.2021.02.061 ↗
9. Interactions of solutes with crystal defects: a new dynamic design parameter for advanced alloys10.1016/j.scriptamat.2020.11.011 ↗
10. Grain boundary segregation and its implications regarding the formation of the grain boundary α phase in the metastable β-Titanium Ti–5Al–5Mo–5V–3Cr alloy10.1016/j.scriptamat.2021.114320 ↗
11. Crystallography and reorientation mechanism upon deformation in the martensite of an α-α’ Ti-6Al-4V dual-phase microstructure exhibiting high work-hardening rate10.1016/j.actamat.2020.116530 ↗
12. Excellent balance of ultimate tensile strength and ductility in a Ti–6Al–2Sn–4Zr–2Mo–Si alloy having duplex α + α′ microstructure: effect of microstructural factors from experimental study and machine learning10.2320/matertrans.MT-MLA2022009 ↗
13. Micromechanical behavior and thermal stability of a dual-phase α+α’ titanium alloy produced by additive manufacturing10.1016/j.actamat.2018.09.050 ↗
14. Factors determining room temperature mechanical properties of bimodal microstructures in Ti-6Al-4V alloy10.1016/j.msea.2018.06.019 ↗
15. Reorientation Induced Plasticity (RIP) in high-strength titanium alloys: an insight into the underlying mechanisms and resulting mechanical properties10.1016/j.actamat.2023.118679 ↗
16. Strengthening of Ti-6Al-4V alloy by short-time duplex heat treatment10.2320/matertrans.46.1681 ↗
17. Effects of short-time duplex heat treatment on microstructure and fatigue strength of Ti-6Al-4V alloy
18. Forming of titanium and titanium alloys
19. Hot stamping of titanium alloy sheets using partial contact heating10.1016/j.promfg.2018.07.375 ↗
20. Assessment of electrical resistance heating for hot formability of Ti-6Al-4V alloy sheet10.4028/www.scientific.net/KEM.473.130 ↗
21. Fiji: an open-source platform for biological-image analysis10.1038/nmeth.2019 ↗
22. Trainable Weka Segmentation: a machine learning tool for microscopy pixel classification10.1093/bioinformatics/btx180 ↗
23. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
24. Yielding nature and Hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures10.1016/j.scriptamat.2019.07.015 ↗
25. Deformation mechanism of bimodal microstructure in Ti-6Al-4V alloy: the effects of intercritical annealing temperature and constituent hardness10.1016/j.jmst.2020.08.057 ↗
26. A strategy to improve the work-hardening behavior of Ti–6Al–4V parts produced by additive manufacturing10.1080/21663831.2016.1245681 ↗
27. Finite element modeling of the morphology of β to α phase transformation in Ti-6Al-4V alloy10.1007/s11661-002-0204-4 ↗
28. Effects of volume fraction of tempered martensite on dynamic deformation properties of a Ti-6Al-4V alloy having a bimodal microstructure10.1007/s11661-005-1005-3 ↗
29. Grain boundary segregation engineering in metallic alloys: a pathway to the design of interfaces10.1016/j.cossms.2014.06.002 ↗
30. Mechanisms of grain boundary α precipitation in the metastable β-titanium Ti-5Al-5Mo-5V-3Cr10.1016/j.actamat.2024.119955 ↗
31. Grain boundary discontinuity and performance improvement mechanism of wire arc additive manufactured Ti–6Al–4V10.1016/j.jallcom.2021.159287 ↗
32. On the strain hardening abilities of α+β titanium alloys: the roles of strain partitioning and interface length density10.1016/j.jallcom.2019.152040 ↗
33. Influence of alloy element partitioning on strength of primary α phase in Ti-6Al-4V alloy10.1016/j.jmst.2017.07.016 ↗
34. Towards work-hardenability of Ti-6Al-4V through a quenching and partitioning approach10.1051/matecconf/202032111062 ↗
35. Phase transformations in the Ti-V system under high pressure up to 25 GPa10.1016/0001-6160(81)90071-7 ↗