Fatigue crack growth behavior of Alloy 247DS brazed joints at high temperatures
Source abstract
Abstract
Gas turbine components made of nickel-based alloys can be repaired through diffusion brazing. However, process-induced imperfections, defects within the brazing zone, and material property mismatches between the braze alloy and base material may facilitate crack initiation and propagation, ultimately leading to early component failure. To gain insight into the crack growth mechanism and quantitatively characterize fatigue crack growth behavior within brazing zones, fatigue crack growth (FCG) experiments were conducted on brazed joint specimens of nickel-based alloy Alloy 247DS at a temperature of 950 °C and a stress ratio R = 0.1. The FCG tests were complemented by fractographic and microstructural analyses, to elucidate the relationship between crack growth mechanisms and the microstructure of the brazed joint. The results demonstrate stable crack propagation within the brazing zone and the nickel-based braze alloy. The latter contains brittle eutectic boride phases and intermetallic phases that reduce the resistance to crack propagation compared to the parent material. This study demonstrates the applicability of standard FCG experimental procedures to fusion zones, thereby enabling a preliminary understanding of crack growth behavior in brazing zones.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Fatigue and fracture mechanics · Fire effects on concrete materials · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Donachie · 2002
2. Failure analysis of gas turbine first stage blade made of nickel-based superalloy10.1016/j.csefa.2017.04.002 ↗
3. Microstructure and high temperature tensile properties of narrow gap braze joint between X-40 and IN73810.1179/174328408X369401 ↗
4. Bradley · 1988
5. Prager · 1968 · 128
6. Evaluation of transient liquid phase bonding between nickel-based superalloys10.1023/A:1017513200502 ↗
7. Diffusion braze homogenisation and contraction during re-repair heat treatments of a single crystal nickel-based superalloy10.1016/j.jallcom.2020.157560 ↗
8. Cohesive zone modeling of fatigue crack growth in brazed joints10.1016/j.engfracmech.2014.03.014 ↗
9. Creep and fatigue lifetime analysis of directionally solidified superalloy and its brazed joints based on continuum damage mechanics at elevated temperature10.1016/j.matdes.2012.09.052 ↗
10. Coaxial control of aluminum and steel laser brazing processes10.1016/j.phpro.2011.03.094 ↗
11. Amorphous sputter coating of a multi-component Zr–Ti–Ni–Cu alloy as a filler for brazing Zircaloy-410.1016/j.jnucmat.2012.03.024 ↗
12. Messler · 2004
13. Transient liquid phase bonding10.1179/136217104225021724 ↗
14. Wide gap braze repair of gas turbine blades and vanes—a review10.1115/1.4003962 ↗
15. Joint characterisation for repair brazing of superalloys10.1007/BF03263404 ↗
16. Effect of tungsten addition on the nucleation of borides in wide gap brazed joint10.1115/1.4000136 ↗
17. Effects of gap filler and brazing temperature on fracture and fatigue of wide-gap brazed joints10.1007/BF00353041 ↗
18. Fast isothermal solidification during transient liquid phase bonding of a nickel alloy using pure copper filler metal: solubility vs diffusivity10.1007/s11661-019-05149-5 ↗
19. Influence of process parameters on microstructure of transient liquid phase bonded Inconel 738LC superalloy with Amdry DF-3 interlayer10.1016/j.msea.2005.10.056 ↗
20. Fatigue and cyclic deformation behavior of brazed steel joints10.1016/j.msea.2013.05.083 ↗
21. Fatigue properties of narrow and wide gap braze repaired joints10.1115/1.4002824 ↗
22. Experimental investigation on both low cycle fatigue and fracture behavior of DZ125 base metal and the brazed joint at elevated temperature10.1016/j.msea.2011.05.085 ↗
23. Effect of strain rate and temperature on yielding and fracture toughness of brazed joints of inconel 718
24. 2014 · 1
25. 2012
26. 2018
27. 2018
28. Calibration of the potential drop method for monitoring small crack growth from surface anomalies – crack front marking technique and finite element simulations10.1016/j.ijfatigue.2014.09.003 ↗
29. Johnson · 1965 · 442
30. ImageJ for microscopy
31. NIH Image to ImageJ: 25 years of image analysis10.1038/nmeth.2089 ↗
32. An assessment of different approaches for measuring crack sizes in fatigue and fracture mechanics specimens10.1016/j.tafmec.2021.103119 ↗
33. Tada · 2000
34. 2019
35. An overview of fracture mechanics with ANSYS10.30880/ijie.2018.10.05.010 ↗
36. 2021 · 10
37. 2018
38. Investigation of crack tunneling in ductile materials10.1016/j.engfracmech.2010.06.010 ↗
39. The influence of temperature and orientation on fatigue crack growth behavior of a directional solidification nickel-based superalloy: experimental investigation and modelling10.1016/j.ijfatigue.2019.04.024 ↗
40. Experimental investigation on high-cycle fatigue of inconel 625 superalloy brazed joints10.1007/s11661-018-4474-x ↗
41. Mechanical properties and structure of laser beam and wide gap brazed joints produced using mar m247–amdry DF3 powders10.1115/1.4041009 ↗
42. Intermetallic phase formation during brazing of a nickel alloy using a Ni–Cr–Si–Fe–B quinary filler alloy10.1080/13621718.2018.1553280 ↗
43. Microstructure and high temperature tensile properties of wide gap brazed cobalt based superalloy X-4010.1179/174328408X382217 ↗
44. Fatigue crack deflection and fracture surface contact: micromechanical models10.1007/BF02815306 ↗