Synchrotron X-ray radiation study of retained austenite stability and the effect on fatigue behavior of bainitic railway steels
Source abstract
Abstract
The effect of retained austenite stability on the fatigue performance was studied in bainitic rail steel subjected to different heat treatments, including normalizing at 900 °C and normalizing at 900 °C combined with tempering at 320 °C. The normalized steel had yield strength of 851 MPa, tensile strength of 1131 MPa, uniform elongation 7.0 %, and total elongation 17.5 %. Tempering the steel at 320 °C resulted in similar strength and plasticity compared to the normalized condition. However, the fatigue performance of steel was improved significantly after tempering. The ultimate fatigue stress (endurance limit) after 1 × 10 7 cycles was 671 MPa, which was 38 MPa greater than the normalized steel. Microstructural analysis revealed similarities between normalized and tempered matrices at crystallographic interfaces and grain boundaries. Synchrotron X-ray radiation indicated that the initial retained austenite content was ∼15.5 % in both normalized and tempered conditions. However, at tensile stress of 800 MPa, the amount of retained austenite transformed in the normalized steel was ∼4 %, which was twice that of the tempered steel. The enhancement of retained austenite stability was an important aspect in improving the fatigue performance. The analysis of interphase spacing showed that the strain in the normalized matrix synchronized with the retained austenite, and the stress was concentrated in the retained austenite, which promoted transformation of retained austenite. The matrix of tempered steel was strained first, which prevented stress concentration in the retained austenite and rendered the retained austenite stable.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. Test and application of 60 kg·m−1 bainite rails for heavy-haul railway10.1108/RS-04-2023-0015 ↗
2. Mechanical properties and fracture toughness of rail steels and thermite welds at low temperature10.1007/s12613-012-0572-8 ↗
3. Effect of deformation parameters on the austenite dynamic recrystallization behavior of a eutectoid pearlite rail steel10.1007/s12613-023-2805-4 ↗
4. Microstructure and mechanical properties of a low carbon carbide-free bainitic steel co-alloyed with Al and Si10.1016/j.matdes.2012.02.053 ↗
5. Design of novel high strength bainitic steels: Part 110.1179/026708301101510348 ↗
6. Design of high-strength and damage-resistant carbide-free fine bainitic steels for railway crossing applications10.1016/j.msea.2019.05.043 ↗
7. The bainitic steels for rails applications
8. Study on carbide-bearing and carbide-free bainitic steels and their wear resistance10.1080/02670836.2016.1242205 ↗
9. Unlubricated sliding and rolling/sliding wear behavior of continuously cooled, low/medium carbon bainitic steels10.1016/S0043-1648(96)07249-3 ↗
10. Stability of retained austenite in multi-phase microstructure during austempering and its effect on the ductility of a low carbon steel10.1016/j.msea.2014.02.059 ↗
11. Effects of austempering temperature on strength, ductility and toughness of low-C high-Al/Si carbide-free bainitic steel10.1007/s11665-015-1567-1 ↗
12. The role of retained austenite on tensile properties of steels with bainitic microstructures10.2320/matertrans.46.1839 ↗
13. Mechanical stability of retained austenite during plastic deformation of super high strength carbide free bainitic steels10.1007/s10853-009-3704-4 ↗
14. A mechanism for the formation of lower bainite10.1007/BF02672558 ↗
15. Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling10.1016/j.msea.2022.143904 ↗
16. Fatigue of extremely fine bainite10.1179/026708310X12688283410244 ↗
17. Rolling contact fatigue of wheel/rail and its advanced research progress
18. Failure mechanism and worn surface microstructure of high manganese steel and bainitic steel crossings10.3901/JME.2008.12.232 ↗
19. Microstructure of the worn surfaces of a bainitic steel railway crossing10.1016/j.wear.2010.01.016 ↗
20. Comparison of fatigue crack growth rate: pearlitic rail versus bainitic rail10.1016/j.ijfatigue.2021.106280 ↗
21. Research progress on rolling contact fatigue damage of bainitic rail steel
22. A novel microstructure of carbide-free bainitic medium carbon steel observed during rolling contact fatigue10.1016/j.scriptamat.2015.11.023 ↗
23. On the role of microstructure in governing the fatigue behaviour of nanostructured bainitic steels10.1016/j.msea.2015.02.016 ↗
24. Microstructural effects on the sub-critical fatigue crack growth in nano-bainite10.1016/j.msea.2018.11.114 ↗
25. Morphologies and characteristics of deformation induced martensite during low cycle fatigue behaviour of austenitic stainless steel10.1016/j.msea.2011.07.011 ↗
26. Mechanisms of fatigue crack propagation in a Q&P-processed steel10.1016/j.msea.2019.03.056 ↗
27. Roles of microstructure in fatigue crack initiation10.1016/j.ijfatigue.2009.10.005 ↗
28. The fatigue properties, microstructural evolution and crack behaviors of low-carbon carbide-free bainitic steel during low-cycle fatigue10.1016/j.msea.2021.141571 ↗
29. Role of retained austenite with different morphologies on sub-surface fatigue crack initiation in advanced bainitic steels10.1016/j.scriptamat.2020.03.036 ↗
30. Effect of tempering on the stability of retained austenite in carbide-free bainitic steel10.1016/j.msea.2022.143525 ↗
31. On the influence of interactions between phases on the mechanical stability of retained austenite in transformation-induced plasticity multiphase steels10.1007/s11661-001-1027-4 ↗
32. Effect of microstructure on the stability of retained austenite in transformation-induced-plasticity steels10.1007/s11661-006-0213-9 ↗
33. Recent progress in third-generation low alloy steels developed under M3 microstructure control10.1007/s12613-019-1939-x ↗
34. Machine learning guided automatic recognition of crystal boundaries in bainitic/martensitic alloy and relationship between boundary types and ductile-to-brittle transition behavior10.1016/j.jmst.2020.12.024 ↗
35. Study on microstructures and properties of carbide-free and carbide-bearing bainitic steels10.1016/j.msea.2017.12.108 ↗
36. Effect of substitution of Si by Al on the microstructure and mechanical properties of bainitic transformation-induced plasticity steels10.1016/j.jmst.2017.09.002 ↗
37. Effects of Al addition on bainite transformation and properties of high-strength carbide-free bainitic steels10.1007/s42243-019-00253-7 ↗
38. Retained austenite stabilisation in low carbon high silicon steel during isothermal holding10.1080/02670836.2018.1537224 ↗
39. Mechanism of subsurface microstructural fatigue crack initiation during high and very-high cycle fatigue of advanced bainitic steels10.1016/j.jmst.2021.08.060 ↗
40. Assessment of microstructure- and inclusion-induced fatigue crack initiation in bainitic/martensitic rail steels: competing and synergistic effects10.1016/j.ijfatigue.2023.107706 ↗
41. Characterization of microstructure obtained by quenching and partitioning process in low alloy martensitic steel10.1016/j.msea.2010.02.020 ↗
42. Effect of fresh martensite on the stability of retained austenite in quenching and partitioning steel10.1016/j.msea.2014.07.054 ↗
43. The relationship between austenite morphology and continuous TRIP effects in forged 4Mn steel10.1016/j.matchar.2022.112172 ↗
44. Transformation-induced plasticity (TRIP) in advanced steels: a review10.1016/j.msea.2020.140023 ↗
45. The effect of martensite content on the fatigue of a dual-phase steel10.1016/0142-1123(81)90047-5 ↗
46. Microstrain in nanostructured nickel oxide studied using isotropic and anisotropic models10.1016/j.physb.2013.04.028 ↗
47. Plasticity of hexagonal systems: split slip modes and inverse Peierls relation in α-Ti10.1103/PhysRevB.89.144105 ↗