Substructure heterogeneity during hot deformation of ferritic stainless steels - Experimental characterization and discussion assisted by a mean-field model
Source abstract
Abstract
International audience ; The microstructure evolution of ferritic stainless steels during hot deformation is complex and needs to be finely described. Quantifying the evolution of the misorientation of low-angle boundaries depending on the thermomechanical path is a key point in controlling the recrystallization of such steels. This paper proposes an experimental methodology based on large-scale electron back-scattered diffraction (EBSD) mapping characterization using a Symmetry 2 camera to track the low-angle boundary evolution. Different thermomechanical paths, from 900 to 1100 °C with strain from 0.3 to 0.9, were studied using uniaxial compression tests. Flow stress follows a usual hardening stage, followed by a slight softening regime, mostly attributed to continuous dynamic recrystallization. Distributions of low-angle boundary populations (density vs sub-grain size) are quantified by two populations either near grain boundaries or inside grain bulk; the proportion of sub-grains at grain boundaries increases with strain. This bimodal distribution is made with a probabilistic Gaussian mixture model. These results are discussed using a modified mean-field model of Gourdet-Montheillet. This model is insufficient to capture the transient stage of continuous dynamic recrystallization unless its set of parameters is adjusted to accommodate the saturation of the density of low-angle boundaries near grain boundaries. This saturation is a result of the low-angle boundary density gradients in the grains.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. A model of continuous dynamic recrystallization10.1016/S1359-6454(03)00078-8 ↗
2. Chapter 7 - recrystallization of single-phase alloys
3. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions10.1016/j.pmatsci.2013.09.002 ↗
4. Jacquet
5. A CDRX-based material model for hot deformation of aluminium alloys10.1016/j.ijplas.2020.102844 ↗
6. Modelling discontinuous dynamic recrystallization using a physically based model for nucleation10.1016/j.actamat.2009.07.024 ↗
7. Nucleation of recrystallization in fine-grained materials: an extension of the Bailey–Hirsch criterion10.1080/09500839.2013.833352 ↗
8. On the activation of recrystallization nucleation sites in Cu and Fe10.1016/j.msea.2008.10.015 ↗
9. Continuous dynamic recrystallization (CDRX) model for aluminum alloys10.1007/s10853-017-1845-4 ↗
10. A model of grain fragmentation based on lattice curvature10.1016/j.actamat.2009.11.020 ↗
11. Characterization of local texture in a moderately deformed polycrystalline AlSi-alloy10.1016/0956-7151(95)00008-J ↗
12. Analysis of local orientation gradients in deformed single crystals10.1016/j.ultramic.2004.11.016 ↗
13. Thomas
14. Poletti
15. Topological aspects in the microstructural evolution of AA6082 during hot plastic deformation
16. Modeling of continuous dynamic recrystallization of Al-Zn-Cu-Mg alloy during hot deformation based on the internal-state-variable (ISV) method10.1016/j.ijplas.2018.03.002 ↗
17. Topological aspects in the microstructural evolution of AA6082 during hot plastic deformation
18. The adiabatic correction factor for deformation heating during the uniaxial compression test10.1361/105994901770344593 ↗
19. Basin hopping as a general and versatile optimization framework for the characterization of biological macromolecules
20. Scikit-learn: Machine Learning in Python
21. DeHoff
22. Prediction of steel flow stresses at high temperatures and strain rates10.1007/BF02667368 ↗
23. On the application of some plasticity laws10.4028/p-SXs81M ↗
24. A grain scale approach for modeling steady-state discontinuous dynamic recrystallization10.1016/j.actamat.2008.11.044 ↗
25. A compilation and analysis of data for the stress dependence of the subgrain size10.1016/0025-5416(86)90265-X ↗
26. S. Gourdet, « Étude des mécanismes de recristallisation au cours de la déformation a chaud de l’aluminium ».
27. Thermally activated glide in face-centred cubic metals and its application to the theory of strain hardening10.1080/14786435908233412 ↗
28. Deformation Microstructure and Recovery