On the overlooked role of microstructure to explain post-punching fatigue performance of advanced high-strength steel
Source abstract
Abstract
This study compares the role of microstructure on post-punching fatigue properties in three advanced high-strength steels (AHSSs) with a high-strength low-alloy (HSLA) steel commonly used in heavy-duty truck chassis. Microstructure characterization, tensile testing, high cycle fatigue (HCF) testing, fatigue crack growth rate (FCGR) testing, and neutron residual stress measurements are conducted. Punching significantly alters the microstructure, causing microstructure refinement, sub-grain formation, defect creation, tensile residual stresses, and a work-hardened shear-affected zone (SAZ) around, and a rough fracture zone, inside the punched hole. At 10 5 cycles, the HCF performance is primarily governed by the fatigue crack growth resistance of the as-rolled microstructure, with minimal sensitivity to punching. However, near the fatigue limit, post-punching fatigue failure is strongly related to strain localization when significant strength difference exists between microconstituents (e.g., martensite and ferrite). Strain localization also promotes sub-grain formation, reducing the local threshold stress intensity factor range (ΔK th ), thus facilitating fatigue crack initiation. In microstructures with smaller strength differences (e.g., ferrite and bainite), sub-grains, together with surface roughness and residual stress, contribute significantly to the post-punching fatigue limit reduction. These findings provide insights into mechanisms of punching-induced fatigue performance degradation, offering potential strategies to optimize fatigue performance of AHSS for new applications. • Post-punching HCF performance around 10 5 cycles is controlled by FCGR behavior. • Post-punching fatigue limit is greatly influenced by punching-induced changes. • Large strength differences between constituents can govern post-punching fatigue crack initiation. • Reduced fatigue limit correlates to strain localization and sub-grain formation.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Fatigue and fracture mechanics · Fire effects on concrete materials · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. Fracture resistance of advanced high-strength steel sheets for automotive applications10.1007/s11661-020-06119-y ↗
2. Outstanding cracking resistance of fibrous dual phase steels10.1016/j.actamat.2021.116700 ↗
3. Microstructural effects on fracture toughness of ultra-high strength dual phase sheet steels10.1016/j.msea.2020.140631 ↗
4. Effect of residual stresses on fatigue strength of high strength steel sheets with punched holes10.1016/j.ijfatigue.2015.06.018 ↗
5. A review of fatigue failure properties from edge defects10.1007/s11668-017-0294-3 ↗
6. Influence of hole-making procedures on fatigue behaviour of high strength steel plates10.1016/j.jcsr.2019.03.005 ↗
7. Influence of processing factors on the sheared-edge formability of vanadium bearing dual-phase steels produced using continuous galvanizing line simulations10.1007/s10853-020-04385-0 ↗
8. Effect of shearing clearance on formability of sheared edge of the third-generation automotive medium-Mn steel with metastable austenite10.1016/j.jmatprotec.2018.04.038 ↗
9. Effects of size and distribution of spheroidized cementite on void initiation in the punched surface of medium-carbon steel10.1007/s11661-020-05854-6 ↗
10. Microstructure, crystallographic texture, and stretch‐flangeability of hot‐rolled multiphase steel10.1002/srin.201900591 ↗
11. Examining the microtexture evolution in a hole-edge punched into 780 MPa grade hot-rolled steel10.1016/j.matchar.2016.05.007 ↗
12. Ductile-to-brittle transition in tensile failure due to shear-affected zone with a stress-concentration source: a comparative study on punched-plate tensile-failure characteristics of precipitation-hardened and dual-phase steels10.1007/s10704-018-0304-9 ↗
13. Early crack initiation mode during tensile fracture process in a punch-processed precipitation-hardened steel plates and evaluation method to treat the crack as an equivalent pre-crack10.1016/j.msea.2022.143534 ↗
14. Microstructure and mechanical property connections for a punched non-oriented electrical steel lamination10.1016/j.msea.2018.04.054 ↗
15. Analyzing the impact of interlocking on non-oriented electrical steel (NOES) laminations: a microstructural and mechanical property perspective10.1016/j.msea.2024.146097 ↗
16. Investigation of the critical factors controlling sheared edge stretching of ultra-high strength dual-phase steels10.1016/j.msea.2021.142070 ↗
17. Investigation of effects of processing on stretch-flangeability of the ultra-high strength, vanadium-bearing dual-phase steels10.1016/j.msea.2020.140094 ↗
18. Improving the stretch flangeability of ultra-high strength TRIP-assisted steels by introducing banded structure10.1016/j.msea.2022.143722 ↗
19. Compositional heterogeneity in multiphase steels: characterization and influence on local properties10.1016/j.msea.2021.142078 ↗
20. Evaluation of factors affecting the edge formability of two hot rolled multiphase steels10.1007/s12613-018-1563-1 ↗
21. Design of cold rolled and continuous annealed carbide-free bainitic steels for automotive application10.1016/j.matdes.2013.02.046 ↗
22. Assessment of the critical parameters influencing the edge stretchability of advanced high-strength steel sheet10.1007/s11665-016-2316-9 ↗
23. The influence of mechanical and CO2 laser cut-edge characteristics on the fatigue life performance of high strength automotive steels10.1016/j.jmatprotec.2010.09.018 ↗
24. Effect of the cutting process on the fatigue behaviour of press hardened and high strength dual phase steels10.1016/j.jmatprotec.2013.05.003 ↗
25. Concurrent influence of an increase in tensile strength and thickness reduction on fatigue strength of hot rolled steel10.2355/isijinternational.34.285 ↗
26. Fatigue strength characterization of high and ultra-high-strength steel cut edges10.1016/j.engstruct.2020.111544 ↗
27. Effect of microstructure on the high cycle fatigue behaviour of DP 600 and SPFH 590 steels with and without a hole10.1080/02670836.2021.1991086 ↗
28. Effect of tensile strength and microstructure on notch-fatigue properties of ultrafine-grained steels10.2355/isijinternational.52.910 ↗
29. High cycle fatigue behavior of V-microalloyed medium carbon steels: a comparison between bainitic and ferritic-pearlitic microstructures10.1016/j.ijfatigue.2016.06.013 ↗
30. Effect of multiphase microstructure on fatigue crack propagation behavior in TRIP-assisted steels10.1016/j.ijfatigue.2019.105425 ↗
31. Effect of vanadium on fatigue performance of a bainitic forging steel10.1016/j.ijfatigue.2022.107398 ↗
32. Effect of microstructure on tensile and fatigue properties of laser-welded DP780 and DP980 high-strength steel joints10.1016/j.msea.2019.03.062 ↗
33. Effect of shear-affected zone on fatigue crack propagation mode10.1016/j.ijfatigue.2018.06.003 ↗
34. Significant reduction of fatigue crack non-propagation limit caused by damage accumulation mode fatigue crack propagation in a precipitation-hardened punched steel plate10.1016/j.msea.2023.144871 ↗
35. Influence of the cutting method on the fatigue life and crack initiation of non-oriented electrical steel sheets10.1016/j.ijfatigue.2023.108073 ↗
36. Simulation of metal punching and trimming using minimal experimental characterization10.1016/j.jmatprotec.2023.118148 ↗
37. Generation mechanism of residual stress at press-blanked and laser-blanking edges of 1.5 GPa ultra-high strength steel sheet10.1016/j.jmapro.2021.05.047 ↗
38. Experimental study of the impact of punching operations on the high cycle fatigue strength of Fe–Si thin sheets10.1016/j.ijfatigue.2015.09.030 ↗
39. High cycle fatigue life estimation of punched and trimmed specimens considering residual stresses and surface roughness10.1016/j.ijfatigue.2024.108384 ↗
40. Pilkey · 1997
41. Grain detection from 2d and 3d EBSD data—specification of the MTEX algorithm10.1016/j.ultramic.2011.08.002 ↗
42. Hedström
43. Neutron strain scanning using a radially collimated diffracted beam10.1016/S0921-4526(00)00481-6 ↗
44. Correlation between microstructure and fatigue properties of hot-rolled thick-plate complex-phase steel10.1016/j.msea.2023.145624 ↗
45. Dowling · 2013
46. Effect of microstructure on fatigue crack propagation and S–N fatigue behaviors of TMCP steels with yield strengths of approximately 450 MPa10.1007/s11661-010-0577-8 ↗
47. Microstructural influences on simultaneous strength and fatigue crack resistance in advanced high-strength steels10.1016/j.ijfatigue.2024.108278 ↗
48. Effect of surface roughness on step-wise S–N characteristics in high strength steel10.1016/S0142-1123(02)00166-4 ↗
49. On the reversibility of dislocation slip during cyclic deformation of Al alloys containing shear-resistant particles10.1016/j.actamat.2011.03.007 ↗
50. Key factors of stretch-flangeability of sheet materials10.1007/s10853-017-1012-y ↗
51. A comprehensive investigation on the damage induced by the shearing process in DP780 steel10.1016/j.jmatprotec.2021.117377 ↗
52. Mechanism of crack initiation and early growth of high strength steels in very high cycle fatigue regime10.1016/j.msea.2019.138648 ↗
53. Mechanism of fatigue crack initiation and propagation in the very high cycle fatigue regime of high-strength steels10.1016/j.scriptamat.2012.07.049 ↗
54. Fatigue life and mechanistic modeling of interior micro-defect induced cracking in high cycle and very high cycle regimes10.1016/j.actamat.2018.07.036 ↗
55. The role of local plasticity during very high cycle fatigue crack initiation in high-strength steels10.1016/j.ijfatigue.2018.02.008 ↗
56. The formation of discontinuous gradient regimes during crack initiation in high strength steels under very high cycle fatigue10.1016/j.ijfatigue.2019.03.026 ↗